*Update* The depth for for "A" belts at 2:21, "AX" belts at 2:32 and "4L" belts at 3:24 belts is actually 5/16" (not the the 3/16" as mentioned). The width for Deep V 4:15 at 3V and 3VX belts are 3/8" or 9.5mm wide ( not 1/2" wide as mentioned) Unfortunately this can't be changed without deleting and re-uploading the video which is why this update is pinned here.
@@AmreSupply It was really perfect. I'm modifying the motor/machine arrangement on a fractional hp woodworking machine, and this made it easy to figure out the belt type and size I had, as well as pick the new required length.
@@nyw11 Glad that its helping your project come together. We also did a video on all motor types with some great animations if you're curious. Its a good video for general knowledge ruclips.net/video/vpspMVQQXRs/видео.html
Hi Phillip, thank you for watching. Sometimes its just easiest when there are some visuals to reinforce the principles. We're glad you found this video informative!
Thanks for watching. Using a string around a pulley will work and just keep in mind most pulleys can be adjusted, so measure with the pulleys set in the middle so you have room to adjust afterwards.
Thanks for watching Qamar, we're glad that you found the video helpful! For steps on the belt tension, there is some info in this video which shows how to replace a belt in a gas furnace. The relevant section is linked: ruclips.net/video/APqq4X_gjUU/видео.html
Thanks for watching. You could try entering the model number of your washer to try to find a parts list for an exact match: www.amresupply.com/lookup If you can't find the part number you can measure the belt and match it based on it's specs.
This was a very educational video. The belt I need replaced has the code O-448E . It's from a Giantex washing machine. Do you know where I could possibly get that one?. It looks like it is a V belt but it's code name begins with an O. 😳
Hi Delora, thank you for watching. The code is likely one specific to that manufacturer. There are a few things that you could do: You can enter your washing machine model number to try to see if the part shows up: www.amresupply.com/lookup As well there are a wide range of washing machine belts belts available that you can browse through: www.amresupply.com/catalog/Belts-Idler-Pulleys-637140-AI1H In your case if the belt is a V belt, you can simple measure the belt using the steps in this video and use generic V-belt as a replacement: www.amresupply.com/catalog/A-4L-Multi-Plus-V-Belts-HR2A
About the fractional L series of belts. A 3L belt for example. Some of them come in a kevlar wrapped variant (eg. 3L300K) commonly used on lawn equipment and snowblowers, I can't find any info anywhere on the max operating parameters of these belts. Any idea how much HP they can handle reliably?
Thanks for watching. This video was geared mostly towards HVAC applications but v-belts are also used for other lawn equipment and snow blowers. I don't have any specific information on the max HP rating of those belts. If you are buying a replacement belt intended for a snow blower then it likely should be fine to handle a range of snowblowers as long as the belt size is matched properly.
Thanks for that. In Australia a lot of our belts are done in metric lingo. e.g. 13A1350. '13' obviously is the top width but is '1350' the inside or outer circumference & are these classical?
Thanks for watching. These sorts of metric belts are not something we carry so I don't have a direct reference from our notes. According to this the 1350 denotes outside circumference: ca-vbeltguys.glopalstore.com/products/13a1350-metric-standard-oem-equivalent-cogged-automotive-v-belt
Does a B belt have more grip--less slippage--than an A belt? I have a wood splitter that slips on the pump pulley with a difficult split using an A belt and I'm wondering if changing to a B belt will improve the grip significantly.
Hi Don, thank you for watching. Overall its best to match the belt width to the intended design. Having an ideal tension (tight but not too tight) and a clean belt will help prevent slippage. If you're curious to learn more this video did a great job explaining how to address slippage. ruclips.net/video/syWiGYDOM70/видео.html
Valuable info ; for the garage ' nut '. Could you do one, on types/kinds of bolt fasteners : both english and metric ones. Same as ' screws '..../ And, the dozen or so different, types of ' threads '. ...../ There is a w h o l e world of ' shop ' and ' garage ' items, which usually GO UN KNOWN to the average user. Some, of us, need to understand, all the types / and therefore uses of them. Thanks again, Sir . (old retired guys_+) Even the types / kinds of 120 and 240 volt sockets, plugs, etc.
Thanks for watching. We'll keep those ideas in mind for future series! Our last series was a refrigerator troubleshooting series: ruclips.net/p/PLCo9SMjkdWBxXf2GEiSiunxAlN3ENxXGq and now we're currently working on some indoor air quality videos.
Great video!!! But i want to buy a belt for my lawn mower. They sais it is a 5/8 belt by 84 inch. But it said "B" and "5L" on the packaging. So it is not really a 5/8? A 5/8 is a 5v belt right?
Thank you, we're glad that you found it helpful! As you can see at 3:48 belts that are 4L will be the same as A. Belts that are 5L are also a B. The width on the B & 5L is 21/32 which is very close to 5/8 (which would be 20/32). So in this case 1/32" difference in width will not matter.
3:00 is the calculation of outer - inner circumference for the A/B/C/D/E belts of 2/3/4/5/6 inches an estimation for an approximate value? Are the belt thicknesses considered to be exact values?
Thanks for watching. The belt thickness should be close however you might get some variation between manufacturers and there might be some warping over time with heavy use. The width and length is needed for matching.
For the cross-sectional dimension graphics, please check your "depth" dimension shown for "A" at 2:21, "AX" at 2:32 and "4L" at 3:24. For these 1/2" top-width belts, you show 3/16" as the specification depth, but it should be 5/16". (As a sanity check, in the graphic at 3:24, would it make sense that the 7/32" depth of a 3L belt would be *greater* than the stated 3/16" depth of a 4L belt?)
Thank you for watching! You are right that the depth mentioned for A, AX and 4L belts should be 5/16". and not 3/16" as shown in the video. Even though we have 5/16 written in the original script that is one typo that made it through. Unfortunately it can't be changed in the video without deleting and re-uploading which would lose all views, comments interactions. There is a pinned post and and update to the description to help clarify that for people.
Hi, can I use a A series belt to replace an 4L-340 belt? May I also know what exact code should I be looking for an A type of belt? I would use it on my old washing machine. I would be grateful if I get a free answer from you. TIA
Thanks for watching. If you have a 4L-340 belt that measures 34 inches from the outside circumference, then the matching A belt will be also have an outside circumference of 34, subtract 2 (as mentioned at 2:57) and you get an inside measurement of 32 inches. That would mean your replacement is an A32 www.amresupply.com/part/4L340-34-inch-X-50-V-BELT If you're replacing the belt on a washer you can also try to find an exact match. www.amresupply.com/catalog/Belts-Idler-Pulleys-637140-AI1H If you enter your washing machine model number in the search on our website it will likely bring up a parts breakdown with the parts listed on the side. Here's an example: www.amresupply.com/lookup/304244/2305336
Thanks. I have a Earthquake Rototiller # 6015v The belt is a cogged 31315 4XLA. I have found it impossible to cross reference. They designed it so you have to buy one of their 50$ belts. They could have put two of the regular belts on it. Never another Earthquake machine. I did order a AX24 - AX-Section Cogged V Belt. We will see if it works.
@@AmreSupply Do belts come in a designated list of sizes or are they available in a continuum of sizes at the whim of the manufacturers? Like is there a 3L366 belt or some such oddballs, or only in steps of 5?
@@hwingerrr5680 Thanks for watching. It depends on the manufacturer but often there are more sizes in the mid range where there are more uses. Since most motors can be adjust, this covers for slight variations in length. As you get into very long belts, there are less available due to it being more specialized.
Thanks for the video. Any idea what code "O-560" means? The number "29" also appears on the belt, about 1.5" away from the "O-560". It's a belt off of a cheap, imported drill press. The measurements are: 3/8" wide x 1/4" deep x 24" outside diameter.
Thank you for watching! It seems like the O-560 code is likely a manufactures internal number rather than a standard code, it doesn't line up with any codes or measurements that we know of. If you found another belt with a O-560 code or designation, it will likely be a direct replacement.
I know I'm late but better than never. There is, indeed, an O type V belt. At least my drill press from Taiwan is using this type of belt. Just like A, B, C, D... The number next to the designated letter is the inner length (millimeter). You can search for O type V belt on AliExpress.
Hi Barny, thank you for watching! We haven't done any videos for automotive parts as AMRE is more focused on the parts needed to keep one's property running effectively. To measure a serpentine belt you can take a piece of string, you'll need about 9 feet. Looking at your owners manual or any reference diagram for your vehicle, tightly wrap the string around the path of the serpentine belt and mark the point that the string overlaps with itself. Now measure the length of string it took to wrap around the path of the serpentine belt. Purchase a belt one size smaller than the size you measured. The actual belt will have tension on it, whereas the string doesn't. If you don't have a reference belt, you'll need the same width belt as what fits in the pulley's with the same number of grooves. Hopefully this helps. If you're curious you should check out more videos on our channel as they are just as detailed as this one. For example we have a whole series on water heaters maintenance and repair: ruclips.net/video/BHUPFLbb8NY/видео.html
Thanks for watching. A K belt will just be a specialty belt for the drill press. This is different than the standard naming but without more information from the manufacturer, can't be sure what other differences there are from standard belts. When it comes to cogged belts, they run cooler, last longer, and are a little bit more efficient.
Thanks for watching. To find a matching belt you can enter your model number for your washing machine into this tool: www.amresupply.com/lookuppart Or match based on outside circumference as M belts are designated by outside length.
I am trying to find a Gates Truflex 4LXA720 belt but cannot find it anywhere. Where can I get a similar belt and what size do I need based on the markings?
Thanks for watching. From the number it seems like it is a 4L with a length of 720. If the belt is cogged you'll want to match that. There can be some variation in how these are numbered and what extra letters and numbers are added depending on the application. In any case you can still doublecheck and measure the belt.
Sir,i am from India i have a wet grinder and that belt is broken difficult to find the same the belt number is poly V belt 4PJ 745 so what is the alternative i can buy please help me
Thanks for watching. I haven't seen YP in referenced to V-belts in general. The YP is likely just part of the manufactures internal system of naming. If you can find an exact replacement using that part number then that would be best as it would remove any doubt, but as long as you match the size and length of the belt then you'll be good to go.
I have a belt that measures 35.3" outside circumference, with a width of 3/8", and height of 1/4". Would that be a FHP 3L belt, since the width is less than the smallest classical belt A size of 1/2"?
trying to piece together a shop fan, took a rope measured 44 inches around both pully's . bought a v-belt 9455 . Measured 1/2 "×46" still to tight. any recommendations. Thanks.
Thanks for watching. If you're able to get the belt over-top of the pulley's then it will stretch with use and will. If it is too tight and it won't mount or won't turn smoothly when installed, then you might need to get a larger belt. The 9455 has an effective length of 45", so the 9460 belt might be a better fit as it measures a bit over 46"
I have an old craftsman drill press. I need to change the belts and they have codes of sr 210 or 4l 210. And the other two are sr 170 4L 170. Any way I can find a replacement for those? Thank you!
Thanks for watching. At AMRE we carry a variety of belts including the 4L 210 www.amresupply.com/part/4L210-21-inch-X-50-V-BELT and the 4L 170 www.amresupply.com/part/4L170-17-inch-X-50-V-BELT
Thanks for watching we're just glad people are finding the video helpful! In the cases that we've seen X is added as a suffix to the belt size. BX is one example: www.amresupply.com/catalog/BX-Molded-Cogged-V-Belts-HR2F Do you have any examples of it shown as a prefix shown like XB?
I have a v- a-23 belt that I measured the outside to be 23 . Everything I find on line says it’s 25 inches long ! What did mean by subtracting 2 inches ? I’m not sure what I’m missing!
Hi Craig, thank you for watching. An classical A-23 belt should measure 25 inches in circumference on the outside and 23 inches on the inside. A 4L-250 FHP belt will have the same exact measurements. Its strange that a belt with A-23 printed to measure 23inches on the outside, but for getting a replacement as long as the measurements are the same then it will fit.
I’m looking at a pulley that says it accommodates “1/2” ABS belt style.” Does anyone know if that 1/2 inch would be referencing the top width, or the depth of the belt? Thx
Thanks for watching. If it only lists one number than that will be for the top width. You can see here on our website that Deep V belts are listed by top width as the main way of sorting: www.amresupply.com/catalog/3V-Deep-Wedge-V-Belts-HR2G
Thanks for watching. That is a hard question to answer as it depends on many factors. If the alignment and tension are right, then a belt can last years without too much wear. In other cases belts will wear down much sooner. If you notice that a belt is wearing down quickly then its often an alignment or tension issue.
2:40 So if a belt happens to be classified as a "classical" belt, then it's measured by the inside circumference rather than the outside, as is done for the FHP and deep Vee belts? That seems like a recipe for confusion... How do you know for sure if it's classical vs FHP? Are the size profiles unique in each type?
For the A belt with the 5/16" height, the calculation of 2*Pi*(5/16) is 1.96, which matches the -2 Delta of inside and outside circumference, but the C belt with 17/32" height is only 3.34", not a Delta of -4". Are those just supposed to be approximations for estimating the inside belt size based on the outside circumference measurement, rather than some exact cross-reference? These are the exact Delta values based on calculations: A 1.96" B 2.55" C 3.338" D 4.712" E 5.694" The C belt is only one that rounds off to a different number than the guidelines given; the other ones seem okay.
@@wingerrrrrrrrr Thanks for watching. When it comes to classical vs FHP, many belts will list both. www.amresupply.com/part/4L380-38-inch-X-50-V-BELT You can still match based on the width and depths, then use either inside or outside diameter to pick a belt. Belts will also stretch and warp over time so that should be factored in. A used belt will never have the same exact measurements as a brand new belt.
@@AmreSupply if the belts are consistently specified as inner or outer circumference it would be more certain. Does the way the part numbers are written clearly define whether they're using one or the other method?
@@wingerrrrrrrrr Classical and FHP belts are the same. They are just two different ways of describing the same belts. That's why many belts, such as the example link, list both numbers.
@@AmreSupply Okay, that clarifies it, in the description on the website, it mentions the dual branding: This classical belt is built to RMA engineering standard IP 20 and is dual branded with classical multiple size and FHP size. FHP designation denotes outside length. Classical designation denotes inside length. Inside length plus 2 inches equals outside length. (For that particular belt thickness) It would have been good if they stuck to one method; I guess the classical inside method was first, and the FHP came later, and became the preferred measurement.
Thank you for watching. The dimensions of a A-33 belt are listed here: www.amresupply.com/part/4L350-35-inch-X-50-V-BELT You can convert any measurement using an online converter or google.
Thanks for watching. That is not a belt that is in our system. You should be able to measure that belt using the steps in the video, or do a google search as it might be within other databases.
Hi Bappy, thank you for watching. All you need to do is convert to inches, and measure the depth of the belt then you should be able to calculate it using the examples in the video.
Thanks for watching. An M type seems to be more of an uncommon type. It's not one that AMRE carries and there is less information available about it. The M-type is likely shaped and can be measured as one of these classical shapes but might have extra properties such as long life, or extra strength for it's size.
Am currently making three 30 mile round trips for part runs because I keep getting the wrong size belt. I’ve never felt so dumb before. I deserve every bad thing that happens in my life. 😂
@@AmreSupply I see the W as a subtext. 4L 300 W. Some suppliers have the normal names and another set with the W at the end. So they must be different.
@@AmreSupply I really appreciate your replies and they have been helpful. The fellow at NAPA said the W means a higher quality belt .... So .... I purchased the $L300W and will try it out tomorrow. Again, thanks for your help.
Thanks for watching. It depends, there are cases where companies move portions of their manufacturing to other countries while maintaining the same testing and quality control while in other cases quality is lost when manufacturing is moved.
Thanks for watching. Z - section belts aren't as common in Canada, so its not one that we focused on in the video. There still should be some resources on the different sizes if you do a bit of searching. You should still be able to measure the width and depth to find a match.
Thanks for watching. We have posted the correction as a pinned comment so that it is visible. We can tell by the comments and likes on this video that many people are finding this video helpful even with a typo present. If we remove the video it would lose all views, comments and interactions. Re-uploading it would mean the new video would start from scratch and wouldn't show up in the search and is unlikely to generate the same kind of views. That would mean thousands of people would not see the new video and the net benefit to people would decrease.
@@AmreSupply I thought you could simply 'cut' out the erroneous audio and substitute correct stuff. I didn't realize it would sink the ship. Good info as is.
@@gordbaker896 It would be helpful to be able to swap out parts of videos but in a way having videos on RUclips unchangeable prevents deceptive practices. Content creators would game the system for viewership, post one thing then swap it. With it unchangeable It means that all comments and likes on a video refer to the same video even after 10 years you know that the video on RUclips was the same when it was originally released. We're glad that you found the video helpful though!
Thanks for watching. Since we are based in Canada we are first working to make translations into French to help our customers in Quebec. Given the amount of work its unlikely that we'll be doing any translations into other languages in the near future.
*Update* The depth for for "A" belts at 2:21, "AX" belts at 2:32 and "4L" belts at 3:24 belts is actually 5/16" (not the the 3/16" as mentioned).
The width for Deep V 4:15 at 3V and 3VX belts are 3/8" or 9.5mm wide ( not 1/2" wide as mentioned)
Unfortunately this can't be changed without deleting and re-uploading the video which is why this update is pinned here.
e6305-72531 can you decode this ?
This is the most clear and eloquent video about motor belts that's ever been made or ever will be made.
Thank you for you kind words! We're glad you found this video helpful!
@@AmreSupply It was really perfect. I'm modifying the motor/machine arrangement on a fractional hp woodworking machine, and this made it easy to figure out the belt type and size I had, as well as pick the new required length.
@@nyw11 Glad that its helping your project come together. We also did a video on all motor types with some great animations if you're curious. Its a good video for general knowledge ruclips.net/video/vpspMVQQXRs/видео.html
Thank you,its 3am and am
studying for my industrial
mechanic exam on belts.
Make me feel good about
futur belt encounters in my
carreer.Thank you AMRE
You're welcome Louis! Sometimes its helpful just to see it all summed up. We're glad you found this helpful in studying for your exam!
Hi brother how was your mechanic exam 2 years ago?
I nailed it,and now my job have nothing to do with belts and I forgot all about it
haha
@@louis-philippelavoie6929 It's crazy to see how our lives pass by so quickly, Didn't expect a reply after 2 years! thanks
thanks, did some belt changing today and my co-worker couldnt explain it well, this gave me a better understanding.
Hi Phillip, thank you for watching. Sometimes its just easiest when there are some visuals to reinforce the principles. We're glad you found this video informative!
How to measure a broken belt
Thank you. Very helpful to know how to get the proper measurements and what the codes mean.
You're welcome Keith! We're glad you found it helpful!
Perfect Explanation. You nailed it!
Thank you, we're just happy to help!
I'm Indian and I learn machnical work ,very helpful your video "Sir" heartly thanks
Thanks Reetesh, we're glad you found the video helpful!
WE HAVE ALOT OF INDIANS EVERYWHERE. WHY
Great explanation, just what I was looking for
Thank you Evan, we're glad you found it helpful!
Thank you! Very thorough. What about measuring when changing a pulley size? String or other material around both pulleys?
Thanks!
Thanks for watching. Using a string around a pulley will work and just keep in mind most pulleys can be adjusted, so measure with the pulleys set in the middle so you have room to adjust afterwards.
I found out the exact size of belt I been searching for
Glad to hear it!
Dear , very nice and informative video also your way of taking is very nice and simple. please tell about perfect measure tension of belt.
Thanks for watching Qamar, we're glad that you found the video helpful! For steps on the belt tension, there is some info in this video which shows how to replace a belt in a gas furnace. The relevant section is linked: ruclips.net/video/APqq4X_gjUU/видео.html
Great video!! Though my belts code shows Z-390E. Any idea where I can find a replacement? It’s for a portable washer.
Thanks for watching. You could try entering the model number of your washer to try to find a parts list for an exact match: www.amresupply.com/lookup
If you can't find the part number you can measure the belt and match it based on it's specs.
3V and 3VX belts are 3/8" or 9.5mm wide belts ( not 1/2" wide as mentioned )
You are right, thank you for spotting that. The pinned post has been updated.
This was a very educational video. The belt I need replaced has the code O-448E . It's from a Giantex washing machine. Do you know where I could possibly get that one?. It looks like it is a V belt but it's code name begins with an O. 😳
Hi Delora, thank you for watching. The code is likely one specific to that manufacturer.
There are a few things that you could do: You can enter your washing machine model number to try to see if the part shows up: www.amresupply.com/lookup
As well there are a wide range of washing machine belts belts available that you can browse through: www.amresupply.com/catalog/Belts-Idler-Pulleys-637140-AI1H
In your case if the belt is a V belt, you can simple measure the belt using the steps in this video and use generic V-belt as a replacement: www.amresupply.com/catalog/A-4L-Multi-Plus-V-Belts-HR2A
Outstanding video. Thank you so much
You're welcome! We're glad that you liked it!
I understand for your valuable knowledge
Thank you, we're just happy to help!
Very informative
Thank you!
About the fractional L series of belts. A 3L belt for example. Some of them come in a kevlar wrapped variant (eg. 3L300K) commonly used on lawn equipment and snowblowers, I can't find any info anywhere on the max operating parameters of these belts. Any idea how much HP they can handle reliably?
Thanks for watching. This video was geared mostly towards HVAC applications but v-belts are also used for other lawn equipment and snow blowers. I don't have any specific information on the max HP rating of those belts. If you are buying a replacement belt intended for a snow blower then it likely should be fine to handle a range of snowblowers as long as the belt size is matched properly.
Thanks for that. In Australia a lot of our belts are done in metric lingo. e.g. 13A1350. '13' obviously is the top width but is '1350' the inside or outer circumference & are these classical?
Thanks for watching. These sorts of metric belts are not something we carry so I don't have a direct reference from our notes. According to this the 1350 denotes outside circumference: ca-vbeltguys.glopalstore.com/products/13a1350-metric-standard-oem-equivalent-cogged-automotive-v-belt
Does a B belt have more grip--less slippage--than an A belt? I have a wood splitter that slips on the pump pulley with a difficult split using an A belt and I'm wondering if changing to a B belt will improve the grip significantly.
Hi Don, thank you for watching. Overall its best to match the belt width to the intended design. Having an ideal tension (tight but not too tight) and a clean belt will help prevent slippage. If you're curious to learn more this video did a great job explaining how to address slippage. ruclips.net/video/syWiGYDOM70/видео.html
Valuable info ; for the garage ' nut '. Could you do one, on types/kinds of bolt fasteners : both english and metric ones. Same as ' screws '..../ And, the dozen or so different, types of ' threads '. ...../ There is a w h o l e world of ' shop ' and ' garage ' items, which usually GO UN KNOWN to the average user. Some, of us, need to understand, all the types / and therefore uses of them.
Thanks again, Sir . (old retired guys_+) Even the types / kinds of 120 and 240 volt sockets, plugs, etc.
Thanks for watching. We'll keep those ideas in mind for future series! Our last series was a refrigerator troubleshooting series: ruclips.net/p/PLCo9SMjkdWBxXf2GEiSiunxAlN3ENxXGq and now we're currently working on some indoor air quality videos.
Great video!!! But i want to buy a belt for my lawn mower. They sais it is a 5/8 belt by 84 inch. But it said "B" and "5L" on the packaging. So it is not really a 5/8? A 5/8 is a 5v belt right?
Thank you, we're glad that you found it helpful! As you can see at 3:48 belts that are 4L will be the same as A. Belts that are 5L are also a B. The width on the B & 5L is 21/32 which is very close to 5/8 (which would be 20/32). So in this case 1/32" difference in width will not matter.
3:00 is the calculation of outer - inner circumference for the A/B/C/D/E belts of 2/3/4/5/6 inches an estimation for an approximate value?
Are the belt thicknesses considered to be exact values?
Thanks for watching. The belt thickness should be close however you might get some variation between manufacturers and there might be some warping over time with heavy use.
The width and length is needed for matching.
For the cross-sectional dimension graphics, please check your "depth" dimension shown for "A" at 2:21, "AX" at 2:32 and "4L" at 3:24. For these 1/2" top-width belts, you show 3/16" as the specification depth, but it should be 5/16".
(As a sanity check, in the graphic at 3:24, would it make sense that the 7/32" depth of a 3L belt would be *greater* than the stated 3/16" depth of a 4L belt?)
Thank you for watching! You are right that the depth mentioned for A, AX and 4L belts should be 5/16". and not 3/16" as shown in the video. Even though we have 5/16 written in the original script that is one typo that made it through. Unfortunately it can't be changed in the video without deleting and re-uploading which would lose all views, comments interactions. There is a pinned post and and update to the description to help clarify that for people.
@@AmreSupply Understood; thanks for confirming!
@@svyt You're welcome! Thanks for commenting and pointing that out!
Hi, can I use a A series belt to replace an 4L-340 belt? May I also know what exact code should I be looking for an A type of belt? I would use it on my old washing machine. I would be grateful if I get a free answer from you. TIA
Thanks for watching. If you have a 4L-340 belt that measures 34 inches from the outside circumference, then the matching A belt will be also have an outside circumference of 34, subtract 2 (as mentioned at 2:57) and you get an inside measurement of 32 inches. That would mean your replacement is an A32 www.amresupply.com/part/4L340-34-inch-X-50-V-BELT
If you're replacing the belt on a washer you can also try to find an exact match. www.amresupply.com/catalog/Belts-Idler-Pulleys-637140-AI1H If you enter your washing machine model number in the search on our website it will likely bring up a parts breakdown with the parts listed on the side. Here's an example: www.amresupply.com/lookup/304244/2305336
thank you for helping
You're welcome Dara!
Thanks. I have a Earthquake Rototiller # 6015v The belt is a cogged 31315 4XLA. I have found it impossible to cross reference. They designed it so you have to buy one of their 50$ belts. They could have put two of the regular belts on it. Never another Earthquake machine. I did order a AX24 - AX-Section Cogged V Belt. We will see if it works.
Thanks for sharing your experience. Keep us posted if it works!
@@AmreSupply
Do belts come in a designated list of sizes or are they available in a continuum of sizes at the whim of the manufacturers? Like is there a 3L366 belt or some such oddballs, or only in steps of 5?
@@hwingerrr5680 Thanks for watching. It depends on the manufacturer but often there are more sizes in the mid range where there are more uses. Since most motors can be adjust, this covers for slight variations in length. As you get into very long belts, there are less available due to it being more specialized.
Thanks for the video. Any idea what code "O-560" means? The number "29" also appears on the belt, about 1.5" away from the "O-560". It's a belt off of a cheap, imported drill press. The measurements are: 3/8" wide x 1/4" deep x 24" outside diameter.
Thank you for watching! It seems like the O-560 code is likely a manufactures internal number rather than a standard code, it doesn't line up with any codes or measurements that we know of. If you found another belt with a O-560 code or designation, it will likely be a direct replacement.
I know I'm late but better than never.
There is, indeed, an O type V belt. At least my drill press from Taiwan is using this type of belt.
Just like A, B, C, D... The number next to the designated letter is the inner length (millimeter).
You can search for O type V belt on AliExpress.
@@namtrieunguyen7630 Thanks for the information. It was helpful.
Great video thank you 🙏,
Please make more videos
You're welcome R. A. Stay tuned we're about to release a video series on water heaters!
Thanks for the video I have a belt marked ak 34 what is the k for
Thanks for watching. The K likely stands for kevlar.
I have a belt that is marked as L4 1177 K, what is the length of this belt? Is it 117.7” long?
Thanks for watching. There are a lot of different numbering that can appear on belts. It's best to measure the belt following the steps in this video.
So have you done a video on how to measure automotive belts (width and length) when all you got is the engine (old belt long disappeared).
Hi Barny, thank you for watching! We haven't done any videos for automotive parts as AMRE is more focused on the parts needed to keep one's property running effectively. To measure a serpentine belt you can take a piece of string, you'll need about 9 feet. Looking at your owners manual or any reference diagram for your vehicle, tightly wrap the string around the path of the serpentine belt and mark the point that the string overlaps with itself. Now measure the length of string it took to wrap around the path of the serpentine belt. Purchase a belt one size smaller than the size you measured. The actual belt will have tension on it, whereas the string doesn't. If you don't have a reference belt, you'll need the same width belt as what fits in the pulley's with the same number of grooves.
Hopefully this helps. If you're curious you should check out more videos on our channel as they are just as detailed as this one. For example we have a whole series on water heaters maintenance and repair: ruclips.net/video/BHUPFLbb8NY/видео.html
My drill press has a k26 belt. Looks like an a belt to me. What is a k belt? Also what are the plusses and minuses of a cogged belt?
Thanks for watching. A K belt will just be a specialty belt for the drill press. This is different than the standard naming but without more information from the manufacturer, can't be sure what other differences there are from standard belts.
When it comes to cogged belts, they run cooler, last longer, and are a little bit more efficient.
I need a washing machine belt M with an inner circumference of 25 inches. What belt should I buy, is it M 25, M 26 or M 27? Thanks for this video.
Thanks for watching. To find a matching belt you can enter your model number for your washing machine into this tool: www.amresupply.com/lookuppart
Or match based on outside circumference as M belts are designated by outside length.
Excellent
Thank you Redmi!
I am trying to find a Gates Truflex 4LXA720 belt but cannot find it anywhere. Where can I get a similar belt and what size do I need based on the markings?
Thanks for watching. From the number it seems like it is a 4L with a length of 720. If the belt is cogged you'll want to match that. There can be some variation in how these are numbered and what extra letters and numbers are added depending on the application. In any case you can still doublecheck and measure the belt.
Sir,i am from India i have a wet grinder and that belt is broken difficult to find the same the belt number is poly V belt 4PJ 745 so what is the alternative i can buy please help me
Thanks for watching. We don't have a parts list or cross reference with that particular number so we can't give you an alternative part.
Great Video :D Thank you
You're welcome Ervin, thanks for watching!
Very informative! BUT, my Snapper lawnmower uses a 7158101 YP belt. Do you have any idea what the YP means ?
Thanks for watching. I haven't seen YP in referenced to V-belts in general. The YP is likely just part of the manufactures internal system of naming. If you can find an exact replacement using that part number then that would be best as it would remove any doubt, but as long as you match the size and length of the belt then you'll be good to go.
Ok, thanks for the reply.
itaintmebabe99
most snapper blade belts are a six sided belt.
Randy Deskins OK, so you don’t know either !
I have a belt that measures 35.3" outside circumference, with a width of 3/8", and height of 1/4".
Would that be a FHP 3L belt, since the width is less than the smallest classical belt A size of 1/2"?
Yes that would be a FHP 3L belt as listed here: www.amresupply.com/catalog/3L-F-H-P-V-Belts-HR2
trying to piece together a shop fan, took a rope measured 44 inches around both pully's . bought a v-belt 9455 . Measured 1/2 "×46" still to tight. any recommendations. Thanks.
Thanks for watching. If you're able to get the belt over-top of the pulley's then it will stretch with use and will. If it is too tight and it won't mount or won't turn smoothly when installed, then you might need to get a larger belt. The 9455 has an effective length of 45", so the 9460 belt might be a better fit as it measures a bit over 46"
I have an old craftsman drill press. I need to change the belts and they have codes of sr 210 or 4l 210. And the other two are sr 170 4L 170. Any way I can find a replacement for those? Thank you!
Thanks for watching. At AMRE we carry a variety of belts including the 4L 210 www.amresupply.com/part/4L210-21-inch-X-50-V-BELT and the 4L 170 www.amresupply.com/part/4L170-17-inch-X-50-V-BELT
Great explanation. However, X is added as a prefix, not a suffix. :)
Thanks for watching we're just glad people are finding the video helpful! In the cases that we've seen X is added as a suffix to the belt size. BX is one example: www.amresupply.com/catalog/BX-Molded-Cogged-V-Belts-HR2F
Do you have any examples of it shown as a prefix shown like XB?
@@AmreSupply No I haven't! I guess I have to brush my English up a bit!!
I have a v- a-23 belt that I measured the outside to be 23 . Everything I find on line says it’s 25 inches long ! What did mean by subtracting 2 inches ? I’m not sure what I’m missing!
Hi Craig, thank you for watching. An classical A-23 belt should measure 25 inches in circumference on the outside and 23 inches on the inside. A 4L-250 FHP belt will have the same exact measurements. Its strange that a belt with A-23 printed to measure 23inches on the outside, but for getting a replacement as long as the measurements are the same then it will fit.
I’m looking at a pulley that says it accommodates “1/2” ABS belt style.” Does anyone know if that 1/2 inch would be referencing the top width, or the depth of the belt? Thx
Thanks for watching. If it only lists one number than that will be for the top width. You can see here on our website that Deep V belts are listed by top width as the main way of sorting: www.amresupply.com/catalog/3V-Deep-Wedge-V-Belts-HR2G
Good morning , i want to ask how long lifetime of vanbelt
Thanks for watching. That is a hard question to answer as it depends on many factors. If the alignment and tension are right, then a belt can last years without too much wear. In other cases belts will wear down much sooner. If you notice that a belt is wearing down quickly then its often an alignment or tension issue.
Why two v belt using some applications, for example lathe machine, can we use single belt
Thanks for watching. Using 2 v-belts is a way of transferring more power with common, less expensive belts rather than using a single larger belt.
2:40 So if a belt happens to be classified as a "classical" belt, then it's measured by the inside circumference rather than the outside, as is done for the FHP and deep Vee belts?
That seems like a recipe for confusion... How do you know for sure if it's classical vs FHP? Are the size profiles unique in each type?
For the A belt with the 5/16" height, the calculation of 2*Pi*(5/16) is 1.96, which matches the -2 Delta of inside and outside circumference, but the C belt with 17/32" height is only 3.34", not a Delta of -4".
Are those just supposed to be approximations for estimating the inside belt size based on the outside circumference measurement, rather than some exact cross-reference?
These are the exact Delta values based on calculations:
A 1.96"
B 2.55"
C 3.338"
D 4.712"
E 5.694"
The C belt is only one that rounds off to a different number than the guidelines given; the other ones seem okay.
@@wingerrrrrrrrr Thanks for watching. When it comes to classical vs FHP, many belts will list both. www.amresupply.com/part/4L380-38-inch-X-50-V-BELT
You can still match based on the width and depths, then use either inside or outside diameter to pick a belt.
Belts will also stretch and warp over time so that should be factored in. A used belt will never have the same exact measurements as a brand new belt.
@@AmreSupply if the belts are consistently specified as inner or outer circumference it would be more certain. Does the way the part numbers are written clearly define whether they're using one or the other method?
@@wingerrrrrrrrr Classical and FHP belts are the same. They are just two different ways of describing the same belts. That's why many belts, such as the example link, list both numbers.
@@AmreSupply
Okay, that clarifies it, in the description on the website, it mentions the dual branding:
This classical belt is built to RMA engineering standard IP 20 and is dual branded with classical multiple size and FHP size. FHP designation denotes outside length. Classical designation denotes inside length. Inside length plus 2 inches equals outside length.
(For that particular belt thickness)
It would have been good if they stuck to one method; I guess the classical inside method was first, and the FHP came later, and became the preferred measurement.
excellent
Thanks for watching!
Hey sir,, can i ask what is the centimeter of A-33??
Thank you for watching. The dimensions of a A-33 belt are listed here: www.amresupply.com/part/4L350-35-inch-X-50-V-BELT You can convert any measurement using an online converter or google.
What size belt. For 48"husqvarna
Thanks for watching. For that belt you should be able to measure it and determine the size based on the instructions in this video.
23100-GK1-0030-Bando do you know the standard size of it?
Thanks for watching. That is not a belt that is in our system. You should be able to measure that belt using the steps in the video, or do a google search as it might be within other databases.
Let, V -belt length 100" and width 13mm, what is belt number?
Hi Bappy, thank you for watching. All you need to do is convert to inches, and measure the depth of the belt then you should be able to calculate it using the examples in the video.
what are M belts like M-21?
Thanks for watching. An M type seems to be more of an uncommon type. It's not one that AMRE carries and there is less information available about it. The M-type is likely shaped and can be measured as one of these classical shapes but might have extra properties such as long life, or extra strength for it's size.
Lesson learned
Thank you for watching.
Am currently making three 30 mile round trips for part runs because I keep getting the wrong size belt. I’ve never felt so dumb before.
I deserve every bad thing that happens in my life. 😂
Thanks for watching. Hope you were able to find the right belt this time!
Sir please I want know how put tention for belt with least please reply to me
Thanks for watching. The only video that we have on adjusting the tension on a belt is for furnace motors: ruclips.net/video/APqq4X_gjUU/видео.html
some id's have a "W" at the end ... what does the "W" mean?
Thanks for watching. That isn't too common and might be just a manufacturer's addition. do you have an example of a code with a "W" at the end?
@@AmreSupply I see the W as a subtext. 4L 300 W. Some suppliers have the normal names and another set with the W at the end. So they must be different.
@@MrJazzohjazz The W likely refers to the belt being "Wrapped" meaning its made with an additional material that increases its strength.
@@AmreSupply I really appreciate your replies and they have been helpful. The fellow at NAPA said the W means a higher quality belt .... So .... I purchased the $L300W and will try it out tomorrow. Again, thanks for your help.
@@MrJazzohjazz You're welcome, we're just happy to help!
Well, aren't we just Mr. Perfect. LOL
Not quite, Mr. Perfect was a little taller www.imdb.com/name/nm0377344/bio
Thanks for watching though!
V belt kitni mm ki hoti h
Belt me spb ka kya Matlab hota hai
Thanks for watching.
❤
Thanks for watching.
I use 3v450 and it’s 3/8
Thanks for watching.
I want a slick belt that slides when I give my car gas but grabs when I'm just cruzing
Thanks for watching.
Brent Road
Thanks for watching.
Bealt joy
Thanks for watching.
way too many Chinese made belts sold that are passed off as quality belts by USA companies.
Thanks for watching. It depends, there are cases where companies move portions of their manufacturing to other countries while maintaining the same testing and quality control while in other cases quality is lost when manufacturing is moved.
my belt is a Z :(
Thanks for watching. Z - section belts aren't as common in Canada, so its not one that we focused on in the video. There still should be some resources on the different sizes if you do a bit of searching. You should still be able to measure the width and depth to find a match.
@@AmreSupply I'm in Scotland, god point :)
Pull this video and put out a New Correct one.
Thanks for watching. We have posted the correction as a pinned comment so that it is visible. We can tell by the comments and likes on this video that many people are finding this video helpful even with a typo present. If we remove the video it would lose all views, comments and interactions. Re-uploading it would mean the new video would start from scratch and wouldn't show up in the search and is unlikely to generate the same kind of views. That would mean thousands of people would not see the new video and the net benefit to people would decrease.
@@AmreSupply I thought you could simply 'cut' out the erroneous audio and substitute correct stuff. I didn't realize it would sink the ship. Good info as is.
@@gordbaker896 It would be helpful to be able to swap out parts of videos but in a way having videos on RUclips unchangeable prevents deceptive practices. Content creators would game the system for viewership, post one thing then swap it. With it unchangeable It means that all comments and likes on a video refer to the same video even after 10 years you know that the video on RUclips was the same when it was originally released.
We're glad that you found the video helpful though!
7.5.wf750b2bdwq model belt
Samasung
Thanks for watching. You can search by part number and model number on our website: www.amresupply.com/
Samsung washing mishin 7.5.wf750b2bdwq model belt
Thanks for watching. You can search by part number and model number on our website: www.amresupply.com/
Sir PL. Speak in hindi
Thanks for watching. Since we are based in Canada we are first working to make translations into French to help our customers in Quebec. Given the amount of work its unlikely that we'll be doing any translations into other languages in the near future.
Belt namber send me
Thanks for watching. You can search by part number and model number on our website: www.amresupply.com/
Mobile number chahie
Thanks for watching.
Excellent
Thank you!