Some of us are using a Student Version of SolidWorks, without the Toolbox add-ins. Would be nice if you can provide the Spur Gear dimensions so we can draw the gear(s).
1:16:43 the triangle cutter is under the fillet. This is not physically possible in the real world. Also, the cut does not extend clear of the end of the part.
You made a mistake when creating the Lag Sleeve. The 21.68 mm measurement below is incorrect. It should be 20.74 mm. When assembling the hydraulic pump at 1:21:44 you could already see the gap caused by the error at the top. You yourself noticed the error at 1:25:30 . You then worked with the movement lock, but that would not have been correct. Instead, you only should have changed the measurement to 20.74 mm at 54:50, not 21.68 mm. Then you wouldn't have had the assembly problems. 😉🙂 Anyway........awesome Video.
1:12:11 and 1:13:09 A hex is given by it's wrench size - the distance across flats, not across points. It would be impossible to hold manufacturing tolerance across points and is meaningless in reference to wrench tool size.
First of all, Thank you for your lessons. Its helps very much! One thing I didn't understand in this lesson, why did you insert new similar components instead of copying or mirroring it (e.g lag sleeves or housing seal)?
accept my apologies but i have a problem with inserting gears in solid works from the tool box : what even the module and the number of teeth the program only accepts a fixed number of teeth (which is 12 teeth no more or less). thank for the present respond :)
When you have made the sketch of the oil seal, the sketch isn't fully defined. May i ask why? Because i have learned that the sketch should be fully defined before you make an exctrude.
sketch should be fully defined before extruded because there will be chances of error but some time we confident that there is no error or we left some unwanted information which will not affect our geometry. due to time shortage some time i prefer to skip some unwanted dimensions.
How did you come up with 15.23" and 37" early on? Did you get this from a schematic you were following or do a bunch of pre-calculations to figure out how everything would fit together when you went to make your assembly etc?
Dear cad cam tutorial im watching yr precious videos years and years along and following with great pleasure will you pls open o blog or sth and share dimentions jpg or pdf for all yr workings..so we can do with you and we can check ourself from yr videos
you are awesome and the best in Solidworks tutorial. Personal question for you, dimensions in your tutorial is actually from real part or design by yourself?
please can i convert entities on a plan from one sketch to another in the same part or even to another part instead of repeating some sketches . Great work thanks
I tried making 2 set of spur gear. 1 with example 40 sets of teeth, 1 with 11. solidwork show same number of teeth. Tried with different setting in spur gear properties, same spur gear displayed
Could not get the motor to work for the life of me. I'm on SW 2016. Any ideas why it might not be working for me? Did it exactly like you instructed. Thanks for the great tutorial.
Thank you, professorial all these lessons learned, and this wonderful astronomical explanation is simple respect for me, and thank you very much and I wish I could explain to me how to print a drawing on paper after the completion of the design and the commands used and thank you for everything
There are two wrong measures in the beggining of the final assembly, the last part of the project. One of them is the pin hole in the lag sleeve, it must be 1.7mm length (without adding the milimeters provided by the chaffer), not 2mm, due to the chaffer applied to the 2x4pin which will reduce its useful length, since the chaffer will enter in the hole cone. The second is in the lag sleeve itself, in the sketch, it is NOT 21,68, the measure, it's 21mm. Hope this helps boys
Hi! i'm watching the video, and you are awesome! I'm almost finishing the hydraulic pump. But i have a problem. When I try to select the material for de pieces, all the materials show mate. Even if i choose polished iron, for example. How do i do to make them as the should? Thanks!
Thanks for watching. you need professional graphics card in your system like Nvidia quadro series or AMD Fire Pro series. normal graphics card will not support real view in any cad softwares, you must buy a professional graphics card for real view.
@@CADCAMTUTORIALBYMAHTABALAM or modify the register in your version of windows and add your video card chipset onto it. that worked for me on a gaming laptop that I still use.
i am using. workstation laptop, Dell Precision M4800 you need professional graphics card in your system like Nvidia quadro series or AMD Fire Pro series. normal graphics card will not support real view in any cad softwares,
Thank you, you are a genius!. I am a teacher in a secundary technical school in Argentina, and this type of tutorial are very important for me and my teaching practice.. Thank you so much! i will waiting for it
sir maine 4 baar try kiya ye assembly pr ye har baar sleeve gatab honata hai bolts ke side 1 slleve gayab hojta hai upar wala esa kyo ..jab bhi me exploded view pe phocta hoo tbhi ye gayab hojata hai esa kyo sir
Paper sizes are written differently, you draw differently. While the intersection of the diameter circle is 51 mm, you get 51 mm from the center of the two diameters. what is the reason?
you could accomplish the same result in half the time... multyBody techniques, proper use of the sketch tools, and so on. this tutorial is really NOT FOR BEGINNERS, even though the geometry is not very complex
I'm from Türkiye, Bursa City. I'm a teacher. I like your videos. Soryy, my english very little. But, I understand your english. İf you come Turkey, I want know to you.... thank you veyr much for videos...
This was my final project. I had to recreate everything in AutoCad 2D.
Thank you for making it complicated yet very interesting
Sir u have best teaching skilled and u have best knowledge too sir
i have learn solidworks 40% coz of u in 4 days
Thanks for watching, i hope you enjoyed.
I AM STRICTLY FOLLOWING YOUR TUTORIALS SINCE WHEN I STARTED LEARNING SOLIDWORKS AWESOME KNOWLEDGE U HAVE
Thanks for watching.
Finally, this took me a little while to do but it was worth the effort. I learned a lot thanks man.
congrats, try to do Animation with Assembly .
you are a very hardworking person.. Hats off
Some of us are using a Student Version of SolidWorks, without the Toolbox add-ins. Would be nice if you can provide the Spur Gear dimensions so we can draw the gear(s).
thank you very much...you are best of best of teaching tutorial.
thanks,
1:16:43 the triangle cutter is under the fillet. This is not physically possible in the real world.
Also, the cut does not extend clear of the end of the part.
i cant make that thread maybe this is the issue
You made a mistake when creating the Lag Sleeve. The 21.68 mm measurement below is incorrect. It should be 20.74 mm.
When assembling the hydraulic pump at 1:21:44 you could already see the gap caused by the error at the top. You yourself noticed the error at 1:25:30 . You then worked with the movement lock, but that would not have been correct. Instead, you only should have changed the measurement to 20.74 mm at 54:50, not 21.68 mm. Then you wouldn't have had the assembly problems. 😉🙂
Anyway........awesome Video.
Excellent Tutorial.. learned bunch off stuffs
Gracias, eres el mejor. Me alegra que tengas este espíritu de compartir el conocimiento. MIL GRACIAS
made in GermOny 😀best regards from Germany
I a m very happy to see your video
thanks very match
Masya Allah...ilmu yang berguna sekali ini...👍
Great video! I learned a few new tricks. Cool animation.
Thanks.
truth all this group of wonderful video thanks
Thank you Sir, i wish to do better than this.
1:12:11 and 1:13:09
A hex is given by it's wrench size - the distance across flats, not across points.
It would be impossible to hold manufacturing tolerance across points and is meaningless in reference to wrench tool size.
damn this guys is genius
Professor MAHTABALAM always teaches based on good market practices. I would like to see a simulation of a 100 m2 metal warehouse. On 03/11/2023.
thankyou so much for the video.. great teaching!!!
thanks
First of all, Thank you for your lessons. Its helps very much! One thing I didn't understand in this lesson, why did you insert new similar components instead of copying or mirroring it (e.g lag sleeves or housing seal)?
Thank you very much, very helpful
U re the best dude
Thanks for watching, i hope you enjoyed.
wow great doing , can`t wait for more videos
Thanks,
accept my apologies but i have a problem with inserting gears in solid works from the tool box :
what even the module and the number of teeth the program only accepts a fixed number of teeth (which is 12 teeth no more or less).
thank for the present respond :)
very very good perfect pump
NICE VIDEO!!
Thanks for watching, i hope you enjoyed.
you are best in solidworks.keep it up.
thanks,
When you have made the sketch of the oil seal, the sketch isn't fully defined. May i ask why? Because i have learned that the sketch should be fully defined before you make an exctrude.
sketch should be fully defined before extruded because there will be chances of error but some time we confident that there is no error or we left some unwanted information which will not affect our geometry. due to time shortage some time i prefer to skip some unwanted dimensions.
Because he used the advance options. Eg: coincident, equall, parallel and others
How did you come up with 15.23" and 37" early on? Did you get this from a schematic you were following or do a bunch of pre-calculations to figure out how everything would fit together when you went to make your assembly etc?
muy bueno su TRABAJO. Esto es diseñar. gracias por subir videos con esta calidad.
Dear cad cam tutorial im watching yr precious videos years and years along and following with great pleasure will you pls open o blog or sth and share dimentions jpg or pdf for all yr workings..so we can do with you and we can check ourself from yr videos
very usful . thankyou.
Thanks for watching i hope you enjoyed.
good video, thank you for share
you are awesome and the best in Solidworks tutorial. Personal question for you, dimensions in your tutorial is actually from real part or design by yourself?
its non Standard dimension taken from Grabcad,
can you do fundamentals of engineering > cause it you do, I like to buy your tutorials..
well done techear and thanks for you for all the picese please can you teach us how we can make a mold injectin plastic?and again thanks
i have plan in future for mold injection tutorial.
Thanks . Very help tutorial.
please can i convert entities on a plan from one sketch to another in the same part or even to another part instead of repeating some sketches . Great work thanks
Thanks sir ❤❤❤❤❤❤❤
Could you make the 2D design of the hydraulic pump available?
Thanks for the video.
I have problems with spur gear. The display is the same. Although I make different number of teeth.
can you elaborate?
I tried making 2 set of spur gear. 1 with example 40 sets of teeth, 1 with 11. solidwork show same number of teeth.
Tried with different setting in spur gear properties, same spur gear displayed
Could not get the motor to work for the life of me. I'm on SW 2016. Any ideas why it might not be working for me? Did it exactly like you instructed. Thanks for the great tutorial.
Figured it out. Works great.
TABL3SIX let me check again,
شكرا استاذي أنت عبقري
welcome.
Thank you, professorial all these lessons learned, and this wonderful astronomical explanation is simple respect for me, and thank you very much and I wish I could explain to me how to print a drawing on paper after the completion of the design and the commands used and thank you for everything
Thank you very much!!!
thanks for watching.
There are two wrong measures in the beggining of the final assembly, the last part of the project.
One of them is the pin hole in the lag sleeve, it must be 1.7mm length (without adding the milimeters provided by the chaffer), not 2mm, due to the chaffer applied to the 2x4pin which will reduce its useful length, since the chaffer will enter in the hole cone.
The second is in the lag sleeve itself, in the sketch, it is NOT 21,68, the measure, it's 21mm. Hope this helps boys
Thanks mate, saved the day👍
Hi! i'm watching the video, and you are awesome! I'm almost finishing the hydraulic pump. But i have a problem. When I try to select the material for de pieces, all the materials show mate. Even if i choose polished iron, for example. How do i do to make them as the should? Thanks!
Thanks for watching. you need professional graphics card in your system like Nvidia quadro series or AMD Fire Pro series. normal graphics card will not support real view in any cad softwares, you must buy a professional graphics card for real view.
@@CADCAMTUTORIALBYMAHTABALAM or modify the register in your version of windows and add your video card chipset onto it. that worked for me on a gaming laptop that I still use.
1:17:07 why mine is not threaded the threaded is the TIP not the hole helix. I stopped here. Help sir
Parabéns pelo conteúdo, didática de muito fácil entendimento
Thanks,
Thank you for the nice tut. It would be great if you can upload drawing with dimensions for all the parts.
Manoj Randeni Thanks i will try my level best.
CAD CAM TUTORIAL look forward for that ☺️
Very nice sir
Use Warp instead of Extruded cut to get the correct symmetry
i really liked very nice pump ,can make air compressor thank you
Thanks for watching, i am planing to make air compressor but the video will be very lengthy anyways i will try in future.
Just love your videos! Pity that I could not use the gears from Toolbox, It's not working on my SW, so I had to delete my work :(
make gear mates it looks better while running the gears.
am glad you are here
very well done thank you
Which version of solid works is good ? And which version is he working with the tutorial ?
AMAIZING !!!
Thanks for watching.
great job!!!
Thanks,
Za pocetnike je OK!!
what 's kind of computer or laptop did you use for compatible with Solidworks ? real view? thanks
i am using. workstation laptop,
Dell Precision M4800
you need professional graphics card in your system like Nvidia quadro series or AMD Fire Pro series. normal graphics card will not support real view in any cad softwares,
Hey, i would like you post a link with the plans in a PDF format like the ones you showed in the video please sir
Thanks sir❤
Hey bro, the "Design Library" feature doesn´t appear on my screen. I´ve looked everywhere and I can´t find it. HEEELP
Hi sir ur videos are very useful.Where can I get the dimensions(blue prints) which you used here.
Can you make a tutorial video on Axial piston pump
nice video... is it available 2d drawing for our practice... please sir provide a 2D drawing us...
Hola, muy buenos los tutoriales! Es posible conseguir los planos?. Gracias!
i will send you link soon, Diego Sebastian Saez
Thank you, you are a genius!. I am a teacher in a secundary technical school in Argentina, and this type of tutorial are very important for me and my teaching practice.. Thank you so much! i will waiting for it
Podrian pasarme los planos para este modelado? es para un proyecto me urge
Hi ... the tutorial is interesting, can you share the pump plane please ?.
thanks you !!!
best regards.
Thank you very much
How many individual parts make up this assembly? Thanks
total 11 parts.
Please can you help me in drawing control valve assembly for excavator or any heavy equipment... I wish to help me
Sir make a tutorial on centrifugal pump.......
Will you please send the link of this exercise?
Can you provide drawings of this part. i mean isometric and all the detail dimension.
Sir, my spur gear is coming too big and I am unable to modify it. Plz help
good job
Thanks bro i hope you enjoyed,
It would be good to put a website link to download the files to a flat or lower level, please.
no but jpg files attached with video.
Good
sir i can't understand how your select location in 2d in hole wizard position . please help me
where can I get the dimensions?
I can't find any jpg file attached with the video.
can you give me all the 2d pdf drawings, i am practicing the solidworks soft ware. thanks for your nice video
soon i will upload jpg file in my facebook page.
@@CADCAMTUTORIALBYMAHTABALAM sir where is it I did search but not there
sir maine 4 baar try kiya ye assembly pr ye har baar sleeve gatab honata hai bolts ke side 1 slleve gayab hojta hai upar wala esa kyo ..jab bhi me exploded view pe phocta hoo tbhi ye gayab hojata hai esa kyo sir
Ur use real pump dimensions or random dimensions??
My sir give the project on real dimensions mechanicsm.
Please give me ANS.
Do you have this CAD file saved somewhere?
Thank you
My Pleasure.
Sir Please, send me the detail of design, efficiency , estimation etc of hydraulic pump..
Paper sizes are written differently, you draw differently. While the intersection of the diameter circle is 51 mm, you get 51 mm from the center of the two diameters. what is the reason?
End plate at the video time 25 min 57 sec the distance 16.68 mm, how i find it in drawing?
Sir in the end when you select motor for the animation my motor is not moving
Do you have PDF files ?
no but jpg files attached with video.
Thanks
how i can download all this video to me pc
try youtube downloader.
Try internet download manager idl
HOW THE PUMP IS CALLED IN THE SPECIFIC?
you could accomplish the same result in half the time...
multyBody techniques, proper use of the sketch tools, and so on.
this tutorial is really NOT FOR BEGINNERS, even though the geometry is not very complex
gracias.
Pls share sketch download link
bravo
Thanks,
Germony
nice
hi , is it possible to gei the Solidwork file of this video ?
مشكور جداً
Yine yapmışsın yapacağını :)
what you want to say ?
I'm from Türkiye, Bursa City. I'm a teacher. I like your videos. Soryy, my english very little. But, I understand your english. İf you come Turkey, I want know to you.... thank you veyr much for videos...
Thanks for watching, i hope you enjoyed.
sure i will meet you if i visit turkey.
Ne öğretmenisin?