I have one and I use a dewalt 12v lithium battery. I soak all of them in sea foam (in a jar) in my ultrasonic cleaner and I connect each one to the tool set on steady pulse for about 10 mins each. I take the o ring off each injector as I disconnect from the power so that I can keep tract of which ones have been run while soaking and cleaning the entire set. The jar allows me to fill the cleaner with only water and after I finish I simply remove the injectors and cover the jar and set it aside for the next time I need it.
Question. When you pulled the injector out, was the metal tip extremely gunked up with burnt oil and carbon? Mine look terrible, not sure if that is expected or if i have a failed seal somewhere
How much ohms does Siemens DEKA injectors supposed to be and question what you use to stop the fluid from coming out from the hose when u sprayed it with carb cleaner like how you sealed it so it won't leak
Why when I connect my injector or reconnect to battery it clicks?as if it engages. And when I spray the cleaner and active the tool it sprays very little as if it doesn’t engage it properly. What do you think is going on?
@@rafagas5150 Did you figure it out? Every time power is applied & removed the injector cycles or clicks. Power open and depowered closed. When power is applied, you should see the same spray as your can nozzle come through the injector. That has been my experience. If not the same spray, its clogged or not opening all the way? I had an injector that would work beautifully on the bench. When in the motor, would work on cold engine or on interstate driving. However, when I would stop for gas refill or a short period, the injector would get hot and not work? I pulled it back out, on my test stand worked great. Used a heat gun, heated it to 200 degrees, injector would not work till it was cool again. It was the #4 cyl misfire on a 4-cylinder motor so it got most of the heat I guess off the motor. Good Luck
in your video you should have stated number four mode something is wrong and explain do i throw away or using the cleaning works we the audience would understand much clearer
It does matter what connection is positive or negative. You are incorrect, Solenoids operate open or closed. Reversing the polarity with close the injector, therefore NO fuel flow. Read a wiring schematic. It is still Ohms Law.
I have one and I use a dewalt 12v lithium battery. I soak all of them in sea foam (in a jar) in my ultrasonic cleaner and I connect each one to the tool set on steady pulse for about 10 mins each. I take the o ring off each injector as I disconnect from the power so that I can keep tract of which ones have been run while soaking and cleaning the entire set. The jar allows me to fill the cleaner with only water and after I finish I simply remove the injectors and cover the jar and set it aside for the next time I need it.
Put an on/off switch on the positive side from battery to reset
Nice video! Straight forward without bs. Thank you!
Thanks
how did i not find this channel before, great work man
Thanks for your support, appreciate that
@@AliMECH you're welcome keep up the good work 👍👍👍👍
Question. When you pulled the injector out, was the metal tip extremely gunked up with burnt oil and carbon? Mine look terrible, not sure if that is expected or if i have a failed seal somewhere
you should install an ox/off switch so to don't disconnect the cable from battery. aniway good job
I did after this video
DIY adapter... how you make? I see hose and clamps... what is connected to red hose inside to seal? Thank you
Great job by the way.
He uses acidic silicone I'm sure.
What size rubber stopper did you use to attach the spary nozzle?
Thank you. Great video.
Thanks for watching
How much ohms does Siemens DEKA injectors supposed to be and question what you use to stop the fluid from coming out from the hose when u sprayed it with carb cleaner like how you sealed it so it won't leak
شكرا لك حقا استفدت من هذا الفيديو ❤
🙏🙏
may i use cleaning clean set and pulse device together in my workshop with ultrasonic cleaner ?
How can I buy one like this, thanks for helping...
O problem, I put the Amazon link in the description box of the video
Can I just tape down the cleaner nozzle to the open position? Will that be too much pressure?
siutable for DI injectors aswell
?
Very good
Thanks
Can i use continental diesel injector testing
Thank you Sir
Thanks for watching
👍
Can you use alcohol or peroxide to rest, instead of carb cleaner?
Fuel creates gum deposits, I'd stick with a carb cleaner, trust me, that shit cleans real well, real quick.
Can it be used for diesel crdi injector ?
to change the mode i believe you don't have to disconnect the battery.. there is a reset button, top left-hand side... at least mine has
Can you Tell me, If i can Clean my injectors with That Gadget without an Ultra Sonic cleaner?
Can I use it in the car?
❤
🙏
How do you get it? What is the price ?
s.click.aliexpress.com/e/_AMNAR7
Just use a momentary switch which is normally closed type, in other words when not pressed it's always on, when you press it switch off.
I like your steering wheel where do I get one like that and does it work also
Wait so how did you get the red tube clamped to the rubber hose?
I used glue
👍👍
Is it safe for motorcycle injector
Why when I connect my injector or reconnect to battery it clicks?as if it engages. And when I spray the cleaner and active the tool it sprays very little as if it doesn’t engage it properly. What do you think is going on?
I could really use the help thanks
@@rafagas5150 Did you figure it out? Every time power is applied & removed the injector cycles or clicks. Power open and depowered closed. When power is applied, you should see the same spray as your can nozzle come through the injector. That has been my experience. If not the same spray, its clogged or not opening all the way? I had an injector that would work beautifully on the bench. When in the motor, would work on cold engine or on interstate driving. However, when I would stop for gas refill or a short period, the injector would get hot and not work? I pulled it back out, on my test stand worked great. Used a heat gun, heated it to 200 degrees, injector would not work till it was cool again. It was the #4 cyl misfire on a 4-cylinder motor so it got most of the heat I guess off the motor.
Good Luck
Wowww nice
direct injected
?
in your video you should have stated number four mode something is wrong and explain do i throw away or using the cleaning works we the audience would understand much clearer
Does this work with delphi diesel common rail injector?
No
If i do nit have tester can i open it wuth a 12 volts
Where do you get the long straw?
It came with seafoam can
How much this is Electronic injector cleaner
You dont describe how we know that an injector is bad or good by testing with this machine ???
Need help,how we know the positive and negative connection of feul injector?
It's a coil, doesn't matter which one is a positive or negative, it will work however you connect it
How can j get this machine
How much cost
About $27 on amazon
@@AliMECH price increased now 😭
I paid £26 on UK Amazon. It's always more expensive than the USA Amazon.
Price
s.click.aliexpress.com/e/_AMNAR7
How much
Hi
Can you test a diesel common rail piezo injecter?
Witch company
Shit I just got it but didn’t realize I had to get a coupler for the injector. Thought it came with it. 🤔
IT s for Diesel ?
It does matter what connection is positive or negative. You are incorrect, Solenoids operate open or closed.
Reversing the polarity with close the injector, therefore NO fuel flow. Read a wiring schematic.
It is still Ohms Law.
👌
🙏🏻