This video proved invaluable when my Triton Rapide shower began leaking. Obtaining and fitting a new pressure seal as recommended got the job done…….many thanks!
Thank you so much for this video. I've had this exact problem on this model and didn't know where to start. I'm a basic diyer and managed to complete this with your help with minimal problems. My water pipe is in my wall so I had to turn the mains off. On the first try I couldn't get the valve out due to not being able to wiggle the solenoid and valve out of position as the water pipe was in the way, so I unscrewed the box above the valve to get space and went in from the top instead, just pulling the valve a few mm away from the wall to get enough access to the screws. This method didn't work as I couldn't screw the valve top back tight enough to keep it from leaking. So back in I went, and used a bit more force (and bravery) to get the valve out properly and complete the job. Thank you so much, no more leaking shower, no more worry, and all for less than a tenner. Tip for getting that difficult screw in on the left of the valve, put your screw on a magnet and put it in place by going in from the bottom and behind, then attack with a screwdriver from the front, worked like a dream!
Brilliant!... thanks for your comments, It’s always great when a video helps someone out, I’m far from expert, bravery is the word, have a go is my logic, kind regards
Update. 14 months after fitting I've had the same problem. After changing the stabiliser valve again, there's no leaks now but I was expecting it to last longer than 1 year as the previous one was over 10 years old with no problems. I haven't used silicone grease either time, do you think this would prolong the life? (the one I've just replaced was bought from a reputable supplier, and I did clean it and replace it first this time round, but it was still leaking (there was no signs of wear or dirt, just some limescale on the plastic outside of the valve cover that I cleaned off in case it was stopping the top from closing 100 %). Any thoughts anyone please?
I did it! and it worked, thanks for you video, very clear and helpful. I didn't have any silicone grease at hand so did without, hope it holds up, if not I know what to try next.
Sorry my question was not completed, I want to say that I have two units rated 230v and mains power supply available is 220v maximum, presently it is not getting hot and very low water flow hot or cold. Is there a possible way to make the units work.
This video proved invaluable when my Triton Rapide shower began leaking. Obtaining and fitting a new pressure seal as recommended got the job done…….many thanks!
Thank you so much for this video. I've had this exact problem on this model and didn't know where to start. I'm a basic diyer and managed to complete this with your help with minimal problems. My water pipe is in my wall so I had to turn the mains off. On the first try I couldn't get the valve out due to not being able to wiggle the solenoid and valve out of position as the water pipe was in the way, so I unscrewed the box above the valve to get space and went in from the top instead, just pulling the valve a few mm away from the wall to get enough access to the screws. This method didn't work as I couldn't screw the valve top back tight enough to keep it from leaking. So back in I went, and used a bit more force (and bravery) to get the valve out properly and complete the job. Thank you so much, no more leaking shower, no more worry, and all for less than a tenner. Tip for getting that difficult screw in on the left of the valve, put your screw on a magnet and put it in place by going in from the bottom and behind, then attack with a screwdriver from the front, worked like a dream!
Brilliant!... thanks for your comments, It’s always great when a video helps someone out, I’m far from expert, bravery is the word, have a go is my logic, kind regards
Update. 14 months after fitting I've had the same problem. After changing the stabiliser valve again, there's no leaks now but I was expecting it to last longer than 1 year as the previous one was over 10 years old with no problems. I haven't used silicone grease either time, do you think this would prolong the life? (the one I've just replaced was bought from a reputable supplier, and I did clean it and replace it first this time round, but it was still leaking (there was no signs of wear or dirt, just some limescale on the plastic outside of the valve cover that I cleaned off in case it was stopping the top from closing 100 %). Any thoughts anyone please?
Great video and thanks for sharing. I'm having the same model and facing the same issue.
Hi, hope it helps, good luck 😉
There’s a link to the diaphragm in a reply to a comment lower down
@@PitStakProductions Hi ! Thanks for your quick reply ! I realized that afterwards, that's why I edited my comment ! Thank you very much ! Take care !
I did it! and it worked, thanks for you video, very clear and helpful. I didn't have any silicone grease at hand so did without, hope it holds up, if not I know what to try next.
That’s brilliant, so glad it helped, kind regards
A tip : you can watch movies on flixzone. Been using them for watching loads of movies during the lockdown.
@Micah Ira Yea, been watching on Flixzone for months myself =)
@Micah Ira definitely, I've been watching on flixzone for since november myself :D
@Micah Ira Yea, I have been using flixzone for since november myself :D
Very good demonstration sir. Is this the only source of leakage please. Thanks.
Yes at the time, though I’ve fixed an O ring leak on the temperature dial in the past 😉
It worked! Thank you so much for this.
Your welcome, mine still fine
is the shower in the same place as the bath taps
No, opposite end
Great video, thanks.
Do you have link for the water pressure diaphragm?
Thanks, hope it helps, I’ll have a look 👀
www.ebay.co.uk/itm/SHOWER-LEAKING-STABILISER-VALVE-SEAL-PART-FITS-ALL-TRITON-SHOWERS-/170902688403?_trksid=p2349624.m46890.l49292
Many Thanks
Thanks for the vid.Was it leaking out of the bottom?I have water running out while the shower is still running out of the head.Cant locate its source.
Welcome, yes leaking from bottom right, usually the seal this video covers at fault
Hello is it ok to tile/clad around the shower instead of going behind it. Thanks
Hi, I don’t think it’s advisable but if sealed properly then I suppose it can be done
Sorry my question was not completed, I want to say that I have two units rated 230v and mains power supply available is 220v maximum, presently it is not getting hot and very low water flow hot or cold. Is there a possible way to make the units work.
I find in that situation, current is the problem not voltage, it needs to be a least a 30 amp circuit, Hope this helps
Great! What screwdriver do you use on the terminal block screws? They look like those plusminus type screws
I think they’re called positive drive, regards
@@PitStakProductions Wera calls them plusminus Wiha has a different name for them. I thought you knew if it was a Phillips version or Pozi
@@PitStakProductions 'Posidrive'
how to fix when the pressure of water is high the leak comes from thermostat
Not sure, sorry
@@PitStakProductions prd ???
What is the minimum power voltage to operate the shower
220v I think
@@PitStakProductions What is in the manual is "nominal power - rating at 230V
Good informative video. Thanks.
Your welcome, hope it helps, regards
Very helpful
Glad to hear that!
❤❤❤❤
Douche is niet lief
Douche is stoute
?