Hi RC lovers In my experience Before you drive make sure the tyre nut and all screws has been tight and avoid high speed hitting also clean your RC Car after drive & make ready for next drive & enjoy your RC..☺️
You have to let us all know if you do anything for the throttle delay. If you change your remote or your ESC. You have to keep us updated if you did anything like that. Cuz I really would love to know what would fix that throttle delay. Really nice video keep up the good work and I'll keep watching.😊
I actually noticed that the delay is much less if you play around with the throttle trim and when you run a lipo instead if the included lion batts. The best way to make this truck really perform is to change the esc receiver with standalone electronics. When I get back from California I will probably try and replace those. Use a 3s capable esc like a hobbywing esc and your own transmitter and receiver.
I needed a big parking lot , bigger than most seen on RUclips . Luckily there’s my church close by with no posts . I’m only rolling a hbx 16980SA with 3 s around 40 s mph maybe high 40 mph , prob mid . That sucker scoops with a 50c zeee 2200 11 volt. It s been $120 ish on Amazon and we ve all really been enjoying but this one shown is even more speed and has more things like the fans , metal chassis , extra arm pieces and 2 3s batteries ?
I am maybe a bit obsessed, but I go through everything on a RTR when I get it, I am glad I do because I even had to open up the upgraded differentials for my MJX 16207 I ordered, the grease the factory put in them was very sticky like syrup, so the differential had no free play, the other one was also very sticky but had almost no grease in it at all!!! So it would have been an expensive mistake to just have stuck those into the car and run them straight out of the package!
@@RunThatRC I tried to remove as much of the sticky stuff and added high temperature wheel bearing grease, so that should hopefully make those (quite expensive) upgraded differentials last a whole lot longer.
Looks more for dirt . From experiencing watching non RC people take the wheel with a small powerful RC on asphalt can be bad . I start them in the grass or dirt
I don't understand why peopl say it's not hobby grade when it's just not the big brand. It is like saying it's a not a smartphone if it's not Samsung or Apple or Xiaomi. People need to realize hobby grade is the practicality of the product, not the images and branding
To me if it has parts available to fix it then its hobby grade. Some people are just brand snobs. Took a cheap chinese 3s rc to a rc meet and I smoked half the big expensive rigs there. Specially if they ran stock RCs. I just Run That RC if its good no matter the brand.
As far as I can tell there is no 5 press hi speed mode on the one i got. It seems to be in high speed mode by factory. Could I have a newer/older model?
Hii... I recently thinking about to buy mjx 14210 v2...is there any big difference between mjx 14210 v2 and mjx h14bm? Am really confused... please answer me... 🙏🏼
Looks pretty nice, but beware of the Christmas garbage. After Christmas no follow up vids from others or parts available. Deerc 001e just up and completely gon and vids like this were everywhere. This channel Is great though!
Good luck buying parts off your parts list. They don't sell any. And I mean any. This is a 200 dollar throw away. Don't misunderstand, I bought one too. LOL It does seem pretty indestructible. I like the A-arm plastics. It's nylonized just like Black and Decker hand tools. I had an all plastic screw gun fall 30 feet on concrete and just bounced back up. Not a mark on it. Really. My Redcat TRMT10E basher is made out of the same stuff and I can't break it, even in the cold.
You can contact MJX on instagram I believe. They can help source parts if needed. Some parts are available on ebay and aliexpress. I dont think I can break this with the way I bash but I know some of you are big senders so damage is inevitable.
Don't misunderstand, I bought one too. The monster truck version. LOL It does seem pretty indestructible. I like the A-arm plastics. They're nylonized, just like the Black and Decker power hand tools. I had an all plastic screw gun fall 30 feet on concrete and just bounced back up. Not a mark on it. Really. My Redcat TRMT10E basher is made out of the same stuff and I can't break it, even in the cold. It's nice to see almost all the newer vehicles being made out of this stuff. Make sure you locktite all the set screws! @@RunThatRC
Hopefully they don't do a Wltoys & rest on their laurels.. Great video matr.. Stay safe out there & best wishes from Scotland 🏴 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️
@@RunThatRC Is it worth it overall? I feel like I need the on road mini infraction and I’m not gonna buy a bunch them so if you could only have one would you take this or the “Mini infraction?” Keep in mind I have a tone of large scale high end stuff and maybe 6 or 7 minis, including the Ho Bao Hyper tt 😉
@williamperri3437 if you own high end of road bashers then maybe the mini infraction might be the better choice. I really enjoy drifting that model. If off road is more your thing then this truck is what you will need. I think it's worth it specially if you can get it with the discount. Install the tx/rx you like and a hobbywing esc and that should bump performance and drivability.
If it isn't available for sale in your area you can ask a friend that lives in a area where its available. Maybe you can get them to buy one for you and send it to you. Might be cheaper that way if that's a possibility.
@RunThatRC Thats actually helpful, but i think i will go with buying the hypergo 14210 or 14209 and do the upgrades to telescopic driveshaft, pretty much the only difference besides the shell ive come to find out 🤔thanks again 🫡
How do you fix the throttle delay, is it the ESC or TX/RX causing the issue? On my 16207 this TX was very frustrating, it is the biggest let down on the MJX at present. Now I see they are using the same one on this RC.
I noticed with a 3s lipo instead of the lions included you get less delay and setting the throttle trim helps a little. this has the same transmitter but more options and light button moved to the now not fake button and throttletrim added.
@DeputyMikesRc you can squeeze a 2200mah 3s lipo in these but a 1800 to 2000mah fits better. Just make sure to check the measurements of the pack so it fits the battery tray. I usually buy the midrange priced packs vs the cheapest you can get.
depends on how you run it. I'm not always full throttle so I get about 10 mins. Get a decent charger and two extra batteries and you can keep going all day!
I keep seeing more and more review videos coming out on this model, hopefully banggood updated their stocks and i get mine soon as well. Placed my order about a month ago and it's still "Processing" fml
They updated the esc and motor also some updated stronger looking parts like axles. This model also comes stock with two 3s batteries and not 2s like the first version.
I've only had it for a couple months but the electronics seem to be built well so it should last. It is brushless so they typically last longer than brushed RCs. Now as for breaking it, I haven't done that yet, just had a screw come loose on the steering once but so far I can definitely recommend these MJX RCs for the price.
It's supposed to arrive tomorrow! Can't wait! I will always check out rtr ! I always t3ar down, &do a comprehensive inspection of the drive tran 11:34
your going to like this RC. Its a beast!
Hi RC lovers In my experience Before you drive make sure the tyre nut and all screws has been tight and avoid high speed hitting also clean your RC Car after drive & make ready for next drive & enjoy your RC..☺️
Great advice, especially for a new RC owner!
You have to let us all know if you do anything for the throttle delay. If you change your remote or your ESC. You have to keep us updated if you did anything like that. Cuz I really would love to know what would fix that throttle delay. Really nice video keep up the good work and I'll keep watching.😊
I actually noticed that the delay is much less if you play around with the throttle trim and when you run a lipo instead if the included lion batts. The best way to make this truck really perform is to change the esc receiver with standalone electronics. When I get back from California I will probably try and replace those. Use a 3s capable esc like a hobbywing esc and your own transmitter and receiver.
just ordered one just to mess around with great review
They are tiny beasts!
How was it ? Or is it ?
@@Hungrybird474 really easy to use super fast definitely recommend
I wish they would come out with a 10th scale RC car. You think that would be pretty cool?😊👍
A 10th scale of this would be nice for sure!
I needed a big parking lot , bigger than most seen on RUclips . Luckily there’s my church close by with no posts . I’m only rolling a hbx 16980SA with 3 s around 40 s mph maybe high 40 mph , prob mid . That sucker scoops with a 50c zeee 2200 11 volt. It s been $120 ish on Amazon and we ve all really been enjoying but this one shown is even more speed and has more things like the fans , metal chassis , extra arm pieces and 2 3s batteries ?
I am maybe a bit obsessed, but I go through everything on a RTR when I get it, I am glad I do because I even had to open up the upgraded differentials for my MJX 16207 I ordered, the grease the factory put in them was very sticky like syrup, so the differential had no free play, the other one was also very sticky but had almost no grease in it at all!!! So it would have been an expensive mistake to just have stuck those into the car and run them straight out of the package!
definitely a good idea to go thru your RTR rigs. mine had grease but it is that sticky stuff as well.
@@RunThatRC I tried to remove as much of the sticky stuff and added high temperature wheel bearing grease, so that should hopefully make those (quite expensive) upgraded differentials last a whole lot longer.
@philiprccars4340 that's all we can do is maintain and hope they take a bashing!
Not sure about using those drive shafts as dogbones? Those grub screws better be tight!😅
I hope so too. first tume I've seen these used as such but seems to work so far.
Great video man! Common mistake on the wheel nut lol. I’ve got mine on the way through a promo mjx was running can’t wait to check it out!
Yeah not sure why I forgot to give it a once over. Got it back together so I can run it again soon.
This has to be one of the fastest if not best basher in the 14 range . Seems like an uncommon size . This would be a some in 1/10 size imho .
Looks more for dirt . From experiencing watching non RC people take the wheel with a small powerful RC on asphalt can be bad . I start them in the grass or dirt
On part 14433B on H14BM since its metal the screw can break in half in get stuck in it which happened on mine I felt like it should of been plastic
I don't understand why peopl say it's not hobby grade when it's just not the big brand. It is like saying it's a not a smartphone if it's not Samsung or Apple or Xiaomi.
People need to realize hobby grade is the practicality of the product, not the images and branding
To me if it has parts available to fix it then its hobby grade. Some people are just brand snobs. Took a cheap chinese 3s rc to a rc meet and I smoked half the big expensive rigs there. Specially if they ran stock RCs. I just Run That RC if its good no matter the brand.
@@RunThatRC yes man. THAT IS THE WAY !!!@
I am sad that they did away with the side skirts that tucks the body in like on the 1/16 scale models.
those definitely help.
As far as I can tell there is no 5 press hi speed mode on the one i got. It seems to be in high speed mode by factory. Could I have a newer/older model?
I think its the older version because my older one doesn't have that feature either.
Hii...
I recently thinking about to buy mjx 14210 v2...is there any big difference between mjx 14210 v2 and mjx h14bm? Am really confused... please answer me... 🙏🏼
with the brushless you cant unlock it combine this with a 3s battery
Wow what is that dirt jump location? Looks amazing!
Its in Estrella Park southwest of Phoenix.
My friend gave me a 35c battery for this thing and its insane
Looks pretty nice, but beware of the Christmas garbage. After Christmas no follow up vids from others or parts available. Deerc 001e just up and completely gon and vids like this were everywhere. This channel Is great though!
These things need hex screws
definitely would but isn't a deal breaker for me. Still a great rc.
The pin that screw drive shaft into diff cup gets screwed out to and then the car would become like 2wd the pins need to get lock tight screwed on
Same thing happened to mine back left come off and lost wheel nut
This is really common unfortunately. I usually tighten them before I even run them but took a chance this time and it got me hahaha.
yeah i learnt that lesson. its my first rc since i was a kid so learning the ropes @@RunThatRC
Good luck buying parts off your parts list. They don't sell any. And I mean any. This is a 200 dollar throw away. Don't misunderstand, I bought one too. LOL It does seem pretty indestructible. I like the A-arm plastics. It's nylonized just like Black and Decker hand tools. I had an all plastic screw gun fall 30 feet on concrete and just bounced back up. Not a mark on it. Really. My Redcat TRMT10E basher is made out of the same stuff and I can't break it, even in the cold.
You can contact MJX on instagram I believe. They can help source parts if needed. Some parts are available on ebay and aliexpress. I dont think I can break this with the way I bash but I know some of you are big senders so damage is inevitable.
Don't misunderstand, I bought one too. The monster truck version. LOL It does seem pretty indestructible. I like the A-arm plastics. They're nylonized, just like the Black and Decker power hand tools. I had an all plastic screw gun fall 30 feet on concrete and just bounced back up. Not a mark on it. Really. My Redcat TRMT10E basher is made out of the same stuff and I can't break it, even in the cold. It's nice to see almost all the newer vehicles being made out of this stuff. Make sure you locktite all the set screws! @@RunThatRC
Hopefully they don't do a Wltoys & rest on their laurels..
Great video matr..
Stay safe out there & best wishes from Scotland 🏴 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️
I hope so too 🤞
Oh damn yours seems plastic mines came metal I must of got the upgraded version
maybe they updated some parts.
@@RunThatRC yea they did the update this year that’s what warranty company told me
I’ll be honest, it looked perfect at 100% on normal speed without the secret mode.
I agree with you. Don't know why everything has to be overpowered. I run it on the high speed mode but on 2s and its pretty good.
@@RunThatRC Is it worth it overall? I feel like I need the on road mini infraction and I’m not gonna buy a bunch them so if you could only have one would you take this or the “Mini infraction?” Keep in mind I have a tone of large scale high end stuff and maybe 6 or 7 minis, including the Ho Bao Hyper tt 😉
@williamperri3437 if you own high end of road bashers then maybe the mini infraction might be the better choice. I really enjoy drifting that model. If off road is more your thing then this truck is what you will need. I think it's worth it specially if you can get it with the discount. Install the tx/rx you like and a hobbywing esc and that should bump performance and drivability.
Anybody know where i can find this bad boy in CANADA???😢If i order from usa it costs $370 after import fees/shipping fees etc...😫
If it isn't available for sale in your area you can ask a friend that lives in a area where its available. Maybe you can get them to buy one for you and send it to you. Might be cheaper that way if that's a possibility.
@RunThatRC Thats actually helpful, but i think i will go with buying the hypergo 14210 or 14209 and do the upgrades to telescopic driveshaft, pretty much the only difference besides the shell ive come to find out 🤔thanks again 🫡
Seems like to much power for the small size low weight
on 3s with the gyro turned down like mine it definitely is a lot of power. Great runner on 2s as well.
Hey what's better mjx hyper go H14BM or the rlaarlo xdj 006 I need a RC that can go up to 80+ kmh and good for bashing
I would have to say the quality and hobby grade electronics in the MJX Hyper Go h14bm are way better. I'm a fan of MJX RC.
@@RunThatRC I'm hesitating tho, because they say the H14BM doesn't have oil springed shock
@@king_sentry the h14bm has oil filled shocks.
How can you fix the throttle delay?
unfortunately you need to replace the esc to get rid of it. I was hoping just switching to my radio would work but it only made it slightly better.
If this ever drops to $130 ish , I m getting it . Waiting in a. Rlaarlo cf terminator
How do you fix the throttle delay, is it the ESC or TX/RX causing the issue? On my 16207 this TX was very frustrating, it is the biggest let down on the MJX at present. Now I see they are using the same one on this RC.
I noticed with a 3s lipo instead of the lions included you get less delay and setting the throttle trim helps a little. this has the same transmitter but more options and light button moved to the now not fake button and throttletrim added.
@@RunThatRC It is good to know that actual throttle trim was added, thank you so much for this info.
@@RunThatRC what lipo do you recommend?
@DeputyMikesRc you can squeeze a 2200mah 3s lipo in these but a 1800 to 2000mah fits better. Just make sure to check the measurements of the pack so it fits the battery tray. I usually buy the midrange priced packs vs the cheapest you can get.
The first thing you're going to have to do is locktite all the set screws.,
I don’t like the fact how the servo mount was build cause if it breaks you have to get a whole new chassis tray that the u put the battery on and esc
could be an issue for sure.
@@RunThatRC yea I used a zip tie to keep it in hold for now till I wanna switch out the tray but I’ll wait till the tray really fucks up more
How long does the battery last
depends on how you run it. I'm not always full throttle so I get about 10 mins. Get a decent charger and two extra batteries and you can keep going all day!
I keep seeing more and more review videos coming out on this model, hopefully banggood updated their stocks and i get mine soon as well. Placed my order about a month ago and it's still "Processing" fml
if you're in the U.S. they have stock of these on Amazon.com. I believe it still has a discount at the moment.
@@RunThatRC thanks for taking the time to ease my troubled soul
Just ordered from Amazon. $200 minus a $40 coupon so $160 plus tax to my house. I had to order being so cheap.
all good, banggood's stock is up and mine is on it's way
also, guys, heads up: on banggood it's always been 160EUR (about 180$ish)
Any suggestions for a replacement servo?
I don't have one I know of but these seem to be mini servos. between a micro and a standard size.
Dude, that place was custom made for an outcast 6s….
Im looking into getting into my first AARMA possibly. Always interested in them but never pulled the trigger on one.
@@RunThatRC I really want an infraction 3s but spending 45 bucks on new rubber every 3 time out is a bit of a turnoff….
@Run That RC MJX what is the difference between the version 1 and the version 2 ?
They updated the esc and motor also some updated stronger looking parts like axles. This model also comes stock with two 3s batteries and not 2s like the first version.
How many years does this rc car last for?
I've only had it for a couple months but the electronics seem to be built well so it should last. It is brushless so they typically last longer than brushed RCs. Now as for breaking it, I haven't done that yet, just had a screw come loose on the steering once but so far I can definitely recommend these MJX RCs for the price.
lots of years if you never touch it, longevity is subject to use and abuse, as my late ex GF said, hahaha.
What caused the throttle delay?
when first hitting the throttle there is a slight delay. Not sure if its in the esc or transmitter. Might upgrade one with my own electronics.
@@RunThatRC is it the delay problems already solve?
is it servo size 's standard size??
it looks like a mini servo. between a micro and a standard.