Would you mind sharing how the winding of the ferrite is done? you r video shows but how do you connect the center tap? I noticed is 3 wires per turn but when you tap in the center is done with 2 wires.. how is that done? I just need to understand that part.. Hopefully you can PM me? I will appreciate it.
Segunda tentativa, não funcionou. Reduzi a bitola do fio, troquei resistores. Chega 12v na bobina mas não aquece. Estou usando fonte de 12v 3,3 A de notebook.
Hello! collected for sure. does not heat up at all, power supply 12 volts 3 amperes. the diode fr107 is heated. if you take this part in your hands and the transistors are on top, the lower diode fr107 heats up. why ?? I apologize if I wrote it wrong, translated it in Google. ))
Não consegui acompanhar o que você fez entre 3,40 e 3,43. Parece que você desenrolou uma das pontas e puxou-a de volta pela ponta da ferrita. Além disso, a conexão central ajustada magicamente para o meio da bobina. Você pode explicar isso, por favor?
Sir I'm an electronic hobbyist technician. I want to know wether could I print this circuit on a paper and look this diagram and do the same as you had made it. It's a very wonderful iron of 12 volts. IRF transistors are staying very cool not even need heat sink at all..im planning to assemble it in a PVC pipe. With a built in battery back up and also use a charger for it. So that even use it remote areas whare power supply is not in reach and also can be used during power failures.
take more than 2,5mm wire for secondary winding to get lower heating of this wire the temperature divides between cooper heater & secondary winding by difference of their thickness (or/and by difference of electrical resistance) thicker wire have lower resistance, so it heat lower than cooper heater
it's a trick to wind it more symmetrically and faster: you wind the doubled wire strand, which means 6 wires at a time, then you cut them in the middle and resolder on strand with one of the other. Just think it through with a single wire.
primary turns in core, connection didn't show what terminal to be solder together didn't show the polarity of diode, camera too far from components while solder
este video é montagem este circuito não funciona, primeiro motivo as resistência não tem especificação de watts, segundo o transformador primário tem uma união de espiras de fios, qual é esta divisão exata 3 volta da cada lado, terceiro qual a bitola do fio usada no filtro, quantas voltas, duvido muito que isto funcione
Não sabe oq é circuito ZVS? Isso é um inversor, só que abaixa a tensão de 12v para em torno de 1v com alta amperage, tem o primário e secundário e o transformador de ferrite...
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Would you mind sharing how the winding of the ferrite is done? you r video shows but how do you connect the center tap? I noticed is 3 wires per turn but when you tap in the center is done with 2 wires.. how is that done? I just need to understand that part..
Hopefully you can PM me? I will appreciate it.
Amazing for the sailboat, car, camping....
With short power cords, of course: 4 A....
Thanks a million for the beautiful circuit diagram for this simplistic , very useful tool.......
Хороший паяльничек. Надо будет попробовать повторить. Лайк
0:20, Con la polaridad invertida?, como es eso?
with the polarity reversed ?. how is that?
No le hagas caso, capas que soldo los cables al revés y lo uso así :)
So esqueceu de colocar onde fica o positivo no moste ou no resistor que eu nao localizei embora que nao tenha apresentado um esquema
Segunda tentativa, não funcionou. Reduzi a bitola do fio, troquei resistores.
Chega 12v na bobina mas não aquece. Estou usando fonte de 12v 3,3 A de notebook.
Hello!
collected for sure.
does not heat up at all, power supply 12 volts 3 amperes.
the diode fr107 is heated. if you take this part in your hands and the transistors are on top, the lower diode fr107 heats up.
why ??
I apologize if I wrote it wrong, translated it in Google. ))
I would extend the board to screw (insulated) the mosfets, so they would not "dance" and shoot the heat better ...
Não consegui acompanhar o que você fez entre 3,40 e 3,43.
Parece que você desenrolou uma das pontas e puxou-a de volta pela ponta da ferrita.
Além disso, a conexão central ajustada magicamente para o meio da bobina.
Você pode explicar isso, por favor?
Sir I'm an electronic hobbyist technician. I want to know wether could I print this circuit on a paper and look this diagram and do the same as you had made it. It's a very wonderful iron of 12 volts. IRF transistors are staying very cool not even need heat sink at all..im planning to assemble it in a PVC pipe. With a built in battery back up and also use a charger for it. So that even use it remote areas whare power supply is not in reach and also can be used during power failures.
Sr. Puede ayudarme con el proyecto? Deme su correo para escrivirle .. gracias
Can we use magnet of aquarium oxygen machine in place of core it's shape is similar to that
What ohmic resistor did you use in this project?
What material you used for the soldering tip.., Is it copper..?
Que tipo de material. Es el que sacas de jack....se consigue en otro lado..o a otra cosa me funciona
I realy like it.
Can you tell me all the component name that i can buy?
Here you connect red wire to black one.is it ok. Normally we are considering red is +ve & black is -ve
take more than 2,5mm wire for secondary winding to get lower heating of this wire
the temperature divides between cooper heater & secondary winding by difference of their thickness (or/and by difference of electrical resistance)
thicker wire have lower resistance, so it heat lower than cooper heater
Amigo ,boa tarde ! belos trabalhos os seus!!!gostaria quê se desse você montasse uma fonte de 12v 3amperes pra esses projetos aí
Bro try making a 3s bms battery pack
It should carry it well
I met a guy who didn't want others to use his power supply in the laboratory.
In a moment he came to reverse the polarity of the output .. hahaha
Hi, is there a way to increase current from 0.375A to 5A with 12v power supply?
Phiên bản của bạn rất gọn gàn hướng dẫn chi tiết dễ hiểu cảm ơn bạn nhé
Does the cores have to be ferrit
That's good but if that's the case a step up method , it's practical for me to use Glow plugs - direct 12vdc 4amps up, very hot ;
It be cheaper to buy a iron
Hi Bro I really liked it, I'm going to ride it, congratulations
thanks bro
Hey.. how did you make primary windings 3 inputs out of 2 input ? at 3:42 time
I have two ring core from old atx power supplys can i use that instead of this core?
Sir can I use atx inductor for winding the turns for soldering iron and how much turn is need for primary and secondary
Hello.. i have not been able to make it work.. i need help.. i only get one resistor hot..
please explain the pairing of primary wiring?
3 + 3 turn. Please review the video
it's a trick to wind it more symmetrically and faster: you wind the doubled wire strand, which means 6 wires at a time, then you cut them in the middle and resolder on strand with one of the other. Just think it through with a single wire.
Hello! Ring core-47uh, what material should be made of ferrite or atomized iron?
IRFZ44N or IRF 3205 mach.......?
How much Current it takes during heating
While giving 12v power supply Y u connected reverse connection🤔
:)
Very nice
thanks bro.
I want to say thumbs up for no music but come on. Say something please. Great idea
I'm not American, my English is bad
black (+) and red (-) ..GDS...mosfet ???
-12V to PIN S mosfet. +12v to choke
can i replace fr107 diode with in4007 diode?
Nope. Fr107 or UF4007 only
master excellent great job
Great Bro....Indeed excellent work. Thanks for sharing brother.
thanks bro, have a nice day
I thought that I needed two of these ferrite cores and turned them 90* - the soldering iron would become narrow and convenient
Turns and wire diameter for 47uh choke
10 > 15 turn
AMIGO LO PUEDO HACER UN IRF630M Y LA RSISTENCIA DICE VIDEO DE 47 OHMS O DE 100 OHMS
AC or DC voltage???
¿Cuantos watios da el soldador?
~ 40W
Is it corect Colour cord of power suplay? 😇
:)) black +12V . red GND
@@PhdHung you mean black to red & red to black?
12V+ to choke, GND to PIN S mosfet
Can use in 4007 dioda
Я такой же собрал супер, спасибо он уже давно работает!
saludo voy a rvisar si tngo sos componentes para hacerlo de vnezuela
Resitor 47ohm 1/4 or 1 watt ??
or 100 ohm 1/4 or 1 watt ??
Can i use 1n4007 instead of fr107
no, u need fast diode.
the reversed 12 volt supply colours trigger my OCD !
My iron not working mosfet heating too much
Mosfet is very cool.
Mosfet UTC 7809 được không ạ
primary turns in core, connection didn't show what terminal to be solder together
didn't show the polarity of diode, camera too far from components while solder
الله ينور
Sempre projetos icriveis!
thanks bro
Классно получилось!
Лайк 👍🏻
Thanks.
👍
How many current rating do is required for this 12 volts unit ?
u need 12V 3A
este video é montagem este circuito não funciona, primeiro motivo as resistência não tem especificação de watts, segundo o transformador primário tem uma união de espiras de fios, qual é esta divisão exata 3 volta da cada lado, terceiro qual a bitola do fio usada no filtro, quantas voltas, duvido muito que isto funcione
Não sabe oq é circuito ZVS? Isso é um inversor, só que abaixa a tensão de 12v para em torno de 1v com alta amperage, tem o primário e secundário e o transformador de ferrite...
O cara faltou às aulas, como dizia o Chaves "Dá zero pra ele"😂😂😂😂
very nice pcb
thanks bro
Great Job!!!New Subscriber here that is for sure!!!
Muy bueno tu cautin me gustaria hacer uno me gusta la electronica saludos dsd venezuels
ДААА... Чинайцы с такой работай справляются лучше. Но не отчаивайся, лет через 20 станешь профессионалом. :-)
Obrigado pelo tutorial, terminei o meu ficou perfeito
Fiz o meu tudo correto e não esquenta tenho uma fonte de 12v 2a mesmo assim nem sinal que está quente poderia me ajudar ZAP 62996290586
Saludos amigo.. ayudame por favor. Los mosfet que uso son irf630 y los diodos rgp10d.. solo se calienta una resistencia..
Güzel👍👍👍
Connection is correct but wire colour is opposite...... But good project
:))
un irf634 servira
good video, Thank you !!
Thanks for watching
MOSFET pich rate ki please bolben
Eu vou construir um deste, gostei muito,,
أحسن كواية الحام رائع ممتاز شكرآ أخي الحبيب
Parabéns! Excelente projeto e vídeo, muito fácil de acompanhar, estou construindo um igual ao seu depois sinalizo aqui o resultado. Obrigado
Obrigado e boa sorte
i'm make sure you are vietnamese! nail cutter ... lol. good video! you should change BG music, make a difference vietnam 's channel. keep it up!
Sería bueno que hable . O es mudo?
ok..thankd
Please make as mobail signal booster. At home easy way
very nice
thanks bro
素晴らしい。
Thanks bro
дякую добра людино
Nữa. sao anh lam duoc nhiều thứ vay
trong 1 đống bình luận nc ngoài thì có 1 commen vnXD
thank
:D
Kya brain hai bhai
Super)
thanks
You put the POWER inverted???
Black to red and....
jajaja
Is ok
14:00 😸
👍
👍
👍
not working:(((
You mean I need a soldering iron to make a soldering iron... Then what's the point of making it...
Quê pergunta !!!
Projetinho muito legal mano ,ganhou meu joinha
Проект Ака Касян.
goods
Like like like
Okครับผม
👌👌👌👍👍🙏🙏💯💯
И тут Касьянц?
Tip ne op ora panas
Mo