This is not only the best and cleanest job I saw on RUclips but also the simplest and easiest explanation of what can end up as a very messy project. Thank you!
Nice job Roland. I really like how you pinched and held the twisted pair in place and unravel it only enough to be pushed in. This helps the clippings stay together. Secondly, I liked the stand off dressing method, very clean appearance. Looking forward to see the next video. Bravo and thank you.
Oh wow - you have an incredible attention to detail! Glad we're on the same page. If there's ever anything we can do, please don't hesitate to reach out.
Thank you Sir for making this video!! I cannot tell you how many videos I've looked through that only showed a single punchdown sample which left me questioning how to do the rest. Yours is the most complete and straight forward video and then you went on to show alternate methods for organizing. I really appreciate this and you have a great way of demonstrating. You've earned another subscriber! Keep up the great work!
This is generally a very good job, with informative, correct explanation of the whats and whys of termination. My only feedback would be to preserve the twists in the individual pairs right up to the punchdown block. This was mostly the case in the video, with a few pairs being a bit looser than I'd feel comfortable with. Preserving the twists could potentially make the difference between a pass or fail when certifying the cable run, particularly when dealing with higher categories of cable. But this is a small criticism, and again, very good instruction. I've subscribed and look forward to your content!
Hello D. R Stewart, Welcome and thank you for stopping by our channel. Your feedback is very much appreciated as it helps us improve upon future videos. You are absolutely correct about maintaining the twist right up to the punch down block as this helps minimize the introduction of crosstalk between adjacent pairs which is critical during cable certification. Thank you once again for subscribing and sharing our videos and we will continue to produce and share more informative contents.
Very nice and clean work! When I was installing my home network, I had no former experience with those small 10'' patch panels. In comparison to their bigger friends (19'') they seem to lack some cable support from the back. To manage cables routing I added complete support made from aluminum pipes. But what I clearly see on Your video, it wasn't necessary. ;)
Hello Plomako, most of the panels you purchase do not come with the cable support. Over time, gravity works its magic on the cables and they begin to sag. If the terminated cables are not secured properly, they tend to fall out of the IDC and that is when the problem begins. we appreciate you taking time to watch the video. Please stay tuned for more videos
Thanks! Very clear and intuitive training video. You make it look easy! Hahha Thanks for sharing. Now I have to try it with my Patch Panel for my basement rack. Cheers!
muy bueno, arriba de la mesa se lo ve facil, el problema esta cuando lo tenes que hacer en un rack que se encuentra en altura por ejemplo o cuando no tenes mucho margen de cables qua ya estan tirados! ahi empieza el desafio del contorsionista
hola su ny, gracias por tomarse el tiempo para ver nuestro video y compartir sus comentarios. Siempre es un desafío en el lugar de trabajo porque cada sitio tiene sus propios desafíos. Lo más importante es comprender cómo terminar de la manera adecuada para ayudar a minimizar los problemas que pueda tener más adelante. Gracias de nuevo.
Hello Mohsin, It is always a pleasure to hear about how our videos have helped you learn something new. pls subscribe to the channel for more exciting videos
Hace décadas hacia este trabajo, con cable categoría tres que era básicamente cable multipar telefónico. Hice laburos para el banco mundial en Argentina. Me encanta el cableado estructural.
Great tuturial, I'm thinking of getting a patch-panel myself. But I don't agree with the wasteful use and then removal of zip-ties - better leave them on. It's less work, less waste, and it looks better - if you ever happen to be looking behind the patch-panel... :)
Very neat work. Thank you for the explanation on how to keep the pair distribution the same length. My only question is why not route the second set to the other side so that no cables are running om top of the others? It seems like it would be better for troubleshooting later, especially if you had to terminate any cables on the first set.
Hello Darryl, Thanks for reaching out. Ideally that is the best way to split and terminate the cables. However when you have cables coming in bundles of 24, it is a little bit tricky to split them above and ceiling route them that way. Take into consideration that there might be a switch between the panels. I am working on another video that explain this concept. Please stay tuned in for that. Thanks for subscribing and don't forget to turn on your notification
I'm new to learning IT. Exactly what job position will be handling things like you've shown in this video? I'm guessing, network admin? I would love to come to work and have to do things like this all day. So satisfying
Thank you for showing the 2nd way to strap and leave space to panel..nice and pretty but it would have been a night mare to replace or test the 1st cable terminated on panel with the other cables tightly terminated on top the middle.grouping and restrapping with space to access panel termination is ideal.
Hello Jaws, I am very glad you stopped by and left a note. that is very true. the first method is quite difficult to troubleshoot after the fact which make the 2nd part ideal. Glad you noticed the difference. Stay blessed wherever you are.
Hello Seven T, welcome to our channel. We are glad you stopped by and found it informative. Please stay tuned in as we will be posting videos frequently and also let us know if there are specific topics you would want us to cover. Thanks again
Hello and welcome to our channel. we are really excited you took the time to watch our video, we are also new to posting videos on RUclips and based on the feed back we are receiving, we will begin posting videos frequently. Please don't forget to like, share and subscribe so you would receive notifications of new videos we post. Thanks again
You will not need a drip loop if your rack or cabinet has been bolted and the position will not change or move. It helps ensure that your terminations are clean.
Hello Roland if I terminate 2 cables in the patch panel up and down, but only one cable runs to a keystone jack, how do I know which is going to work for the keystone jack?
Thank you for the question. i am not sure i understand 100% however i will try to answer it the way i understood it. Most patch panels will have numbers on the back where the cables are punched down corresponding to the numbers written on the front of the panel. they may also have the wiring scheme printed on the back to help guide you pick a desired scheme of your choice, A or B. At the user or the keystone end you must also terminate the cable using the wiring scheme you used to terminate on the panel. Keystone jacks can also accomodate for both the A and B wiring scheme so you will need to follow the chosen schem to ensure that you have a straight through termination on both ends. I hope i answered your question. let me know if you require additional information
I wonder if you can help me find a cable hook extraction tool like the yellow one you have. I've tried searching everywhere. Do you know who makes it and what the exact name is please? Thank you so much for your time and the fantastic video content.
Thank you for the comment and the subscription. The name of the tool is Probe Pic Tool. The one i used is made by Fluke networks. Here is the link to it on Amazon.ca. www.amazon.ca/Networks-44600000-Insulated-Pocket-Degrees/dp/B000FFRXEQ. You can search the internet and may get a better price. Good luck
Thanks for taking the time to watch and share your feedback. We are always glad to hear from our viewers. Have a great day and don't forget to like, share and subscribe
@@morosso1968 Thank you for your feedback. this means a lot to us as we are also new to posting tutorial videos. we cannot do this without the support and feedback from you. we appreciate your time. we are creating more videos and please don't forget to like, share and subscribe. Stay safe!
@@Delmitraining who wouldn't like and subscribe a channel like this with a very good content. just keep your videos coming, you just don't know how much you help people like me . =)
My house has (15) builder-installed Cat5e T568A cables from 2007 and (8) Cat6 T568B cables that were added this year. When I run these Ethernet lines to my patch panel do I just wire them per there existing designations (T568A or T568B)? Does mixing different Ethernet cable types and wiring schemes create any problems? Thanks!
Thank you for reaching out. When you run the new Cat 6 cables to the Cat 5e patch panel, there are a few things to note. You are at liberty to have cables terminated as either 568A or 568B so long as both ends match. So having white green or green with white stripes as pin 1 and solid green as pin 2 etc. For 568A. When you have white orange or orange with white stripes as your pin 1 and solid orange as pin 2, this would indicate a 568B wiring scheme. Having 568A on one end of the cable and 568B on the other will create a crossover cable. If you are in the position to maintain one wiring scheme, our advice would be to stick to that to avoid future wiring mixups. Finally, termiating a Cat 6 cable on a Cat 5e patch panel will cause the cable to assume the characteristcs of a Cat 5e cable due to the thresholds set for Cat 5e. You will notice a lot of crosstalk at the patch panel. Thank you for reaching out once again and our apologies for the late response. Good luck
Tip: Don't work over your cables like they show when terminating at the patch panel. Rather get an inline patch panel. It reduces installation time by over 50%, nevermind that the this the chance of signal degradation, when.not installed properly.
Keystone jacks are great and are generic, meaning that they are manufactured by many different vendors. My concern typically is who makes the one you might purchase and were they made of quality materials to meet the standard. We have used different types of keystone and some we have had problems with especially in areas of speed and crosstalk. For basics home networking, you shouldn't have any issue. Our advice, however, is to find a reliable distributor if you need them for other data or mission critical purposes. Good luck, and sorry for the late response
Hello AJ, Thank you for reaching out. If I understand your question well, then the answer is yes. The patch panel can be used to service any interner provider. Remember that the patch panel is where all the cables from multiple user locations terminate. So if you have two or more providers, you can terminate them both on the panel. The most important thing is to make sure that, you maintain the same termination standard (568A or 568B) at both ends and remember to label the terminated ports with the appropriate names or designation. I hope this answers your question. Have a great day!
Hello samuel_the_Pro, thank you visiting our channel and your feedback. It is always great to hear from everyone. We will soon be posting a video on using a keystone unloaded patch panel which is faster just as you mentioned. Please don't forget to subscribe, like and share our videos and also turn on your notification to be notified of our new videos. Thanks again. Really appreciated
Hola Ricardo, y gracias por haber contactado con nosotros. Es una pregunta muy buena y práctica. Hay casos en los que el bloque de terminales se daña durante la perforación. cuando esto sucede, lamentablemente, tendrá que reemplazar todo el panel o marcar ese puerto específico como defectuoso para que el cliente sepa que no debe usarlo. debido a casos como ese, prefiero usar los paneles de conexión sin carga.
Hello Abdulazeez, sorry you are experiencing technical difficulties, try using the link below and hopefully it will work for you. ruclips.net/user/delmitraininginstitute Please dont forget to subscribe, like and share our videos.
Hello Mohamed, thank you for reaching out. It really doesn't matter which of the termination standards you choose to adopt. The key though is to make sure that both ends follow the same pinout configuration. I live in Canada and majority of the terminations ae done conforming to the 568A pilot configuration. I will achieve the same results if I were to use the 568B for the video. Hope this answers your question. I hope you have a great day!
FIRST NO ONE terminated patch panel as 568A anymore unless you are working on a PBX system. second leaving that much open wire behind the punch is against code
Hello, thank you for stopping by. I live in Canada and we do a lot of 568A terminations. Our neighbors down south, the Americans do a lot of 568B wiring. As per TIA, you are at liberty to use any of the two wiring schemes as long as both ends are the same for a straight through connection. Also, the notion of 568A used only for PBX is incorrect. It might have been widely used in the past for such purposes however, i am aware of many other jurisdictions around the world that still use 568A scheme. Now to your second question, Cat 5e cables are known to have a less twist ratio per inch. When terminating them, you may experience a wider gap expecially on the blue pair due to this reason, and this explains why there is so much crosstalk at the panel. Thanks for the learning opportunity. Have a great day!
Thank you for reaching out. We decided to terminate on the table to explain the process. if you want to see how we terminate on the patch panel in a rack, check out our other videos. ruclips.net/video/Tw9dPwFy9AA/видео.html. Once you are done, show us your work as well so we may learn from you. Thanks
Hello Antonio Arizo, Thanks for watching our video. unfortunately, there are no wastage of cables because any excess cables that were cut off were recycled. This is the correct method to have your cables terminated onto a patch panel. It is always better to have an extra foot of cable than to have an inch short. It is very important not to dispose of copper cabling without properly recycling them. We are very fortunate to have facilities that would recycle and reuse the cables that we scrap. We would be glad if you have a better method of terminating patch panels as we would love to learn from you. Thank you once again
Hello Computer Service Slovakia, Thanks for reaching out. This video is a tutorial on how to properly terminate an unshielded twisted pair cables onto a loaded patch panel. Grounding is an important part of the design of any network closet. TIA, ISO and CENELEC have recommendations regarding the proper steps required for grounding and bonding. Even though they have their recommendation, they always recommend to consult the local fire codes bases on your jurisdiction. In every network closet, grounding is an important part of the overall design and the network rack or cabinet must always be properly grounded. When terminating UTP cables on an unshielded panel, there is no need to ground the individual patch panel because the rack or cabinet should have already been grounded. The situation is different when working with shielded cables. with regards to shielded cables, each shielded patch panel must be individually grounded to help dissipate all unwanted noise to ground. if you have any specific concerns, please let us know and we will address it.
Hello again, since this is a channel dedicated to sharing knowledge, I will take this opportunity to educate you. There are different categories of cables available on the market today right up from Cat 5e to Cat 8. All these cables have different frequencies to which the operate. The higher their frequencies the more bandwidth they have and this also increases the data transfer rate. There are additional factors to this such as the amount of twist per inch of each of the pairs to help eliminate crosstalk and also the cable gauge used. Most network applications in today's use require speeds of up to 1Gbps. Unshielded Cat 5e and Cat 6 cables are designed to support such speeds in environments with little to no interference which is our every day life application when the cabling is installed and supported properly up to 100 meters, 300ft. Unshielded Cat 6A supports speeds up to 10Gbps and is backward compatible with Cat 5e and Cat 6. Bear in mind that most network equipment in our day to day use does not support this speed. Such speeds are required in areas where high bandwidth application are required such as data centers etc. Cat 7 to 8 are designed to support speeds of up to 40Gbps. To achieve this speed their construction must include Shielding of the individual pairs and an overall braiding with an increased cable gauge. Even with all these added bells and whistles, the max channel length is 30 meters for 40Gbps and 10Gbps at 100 meters. Now, when working in areas with high interfering sources such as factories with lots of RF generating sources or applications for Audio Visual, Shielded cable is recommended and the category of the cable depends on the desired speed So now I hope you understand why UTP cables are the preferred cable for every day applications. Thank you for reading and don't forget to subscribe, like and share our videos
The ONLY neat IT installer I have ever seen!
Thanks a lot for the feedback. Greatly appreciated
finally, someone on RUclips who knows how to correctly patch a panel!
Phill80, we are grateful to have you check our channel out and we are glad you enjoyed watching our videos. Please stop by again soon
This is not only the best and cleanest job I saw on RUclips but also the simplest and easiest explanation of what can end up as a very messy project. Thank you!
Hello Krzysztof, Thank you for stopping by. we really appreciate your feedback and we are encouraged to produce more contents. Thanks again
Been a wireman for years and I still learned a lot from this video. Thank you.
Excellent 🎉, I learnt a lot
I like the fact you ensured all the pairs are roughly the same length. I've not paid attention to this aspect before.
Craftsmanship and finesse explained with clarity!
Thank you. Greatly appreciated
Well done. Clear and easy to understand every step. You are a gifted teacher!
Thank you. I am glad it was clear and concise
Nice job Roland. I really like how you pinched and held the twisted pair in place and unravel it only enough to be pushed in. This helps the clippings stay together. Secondly, I liked the stand off dressing method, very clean appearance. Looking forward to see the next video. Bravo and thank you.
Oh wow - you have an incredible attention to detail! Glad we're on the same page. If there's ever anything we can do, please don't hesitate to reach out.
This is a masterpiece in teaching
Thanks again and please don't forget to subscribe
Thank you Sir for making this video!! I cannot tell you how many videos I've looked through that only showed a single punchdown sample which left me questioning how to do the rest. Yours is the most complete and straight forward video and then you went on to show alternate methods for organizing. I really appreciate this and you have a great way of demonstrating. You've earned another subscriber! Keep up the great work!
Thanks for watching and also for the comment. Love it
I’ve done many installs and was rather impressed with your work. Keep up the perfectionism 👍
Thanks for the feedback
You have no clue how much I needed this, I can't thank you enough 🙏🏻
THANK YOU VERY MUCH
Thank you so much. We are humbled
Best tutorial on youtube
Great video and explanation from a true pro in the business, thank you.
Thank you. Greatly Appreciated
Simplification at its best, thank you for such a unique video.
Thanks for stopping by.
Very nice and informative...I cannot tell you how many patch-panel wiring nightmares I've walked into...👍
Hello Tom, Thank you for the feedback. I really appreciate the feedback. it encourages us to post more videos. Stay safe
Wire management and bracket is always needed so you can easily troubleshoot lines in the future 🙌
It also makes the work look nicer with less stress on the IDCs
I enjoyed this thoroughly. Simple, easy to understand and very neat. Keep up the quality work!
Hello Dave,
Thank you for stopping by. we truly appreciate the feedback. Have a great day
This is generally a very good job
Thank you
Exellent demo sir
Greatly Appreciated
This is generally a very good job, with informative, correct explanation of the whats and whys of termination. My only feedback would be to preserve the twists in the individual pairs right up to the punchdown block. This was mostly the case in the video, with a few pairs being a bit looser than I'd feel comfortable with. Preserving the twists could potentially make the difference between a pass or fail when certifying the cable run, particularly when dealing with higher categories of cable. But this is a small criticism, and again, very good instruction. I've subscribed and look forward to your content!
Hello D. R Stewart, Welcome and thank you for stopping by our channel. Your feedback is very much appreciated as it helps us improve upon future videos. You are absolutely correct about maintaining the twist right up to the punch down block as this helps minimize the introduction of crosstalk between adjacent pairs which is critical during cable certification. Thank you once again for subscribing and sharing our videos and we will continue to produce and share more informative contents.
Very nice and clean work! When I was installing my home network, I had no former experience with those small 10'' patch panels. In comparison to their bigger friends (19'') they seem to lack some cable support from the back. To manage cables routing I added complete support made from aluminum pipes. But what I clearly see on Your video, it wasn't necessary. ;)
Hello Plomako, most of the panels you purchase do not come with the cable support. Over time, gravity works its magic on the cables and they begin to sag. If the terminated cables are not secured properly, they tend to fall out of the IDC and that is when the problem begins. we appreciate you taking time to watch the video. Please stay tuned for more videos
Thank you so much. Greetings from Colombia
Hello William, much appreciated. Regards from Canada
You are an excellent teacher!
Thanks! Very clear and intuitive training video. You make it look easy! Hahha Thanks for sharing. Now I have to try it with my Patch Panel for my basement rack. Cheers!
Hello Muddy,
Glad you are going to try it. we will love to see your finished product. Please feel free to reach us if you need additional assistance
Excellent tutorial! Thanks for posting it.
Thank you
muy bueno, arriba de la mesa se lo ve facil, el problema esta cuando lo tenes que hacer en un rack que se encuentra en altura por ejemplo o cuando no tenes mucho margen de cables qua ya estan tirados! ahi empieza el desafio del contorsionista
hola su ny, gracias por tomarse el tiempo para ver nuestro video y compartir sus comentarios. Siempre es un desafío en el lugar de trabajo porque cada sitio tiene sus propios desafíos. Lo más importante es comprender cómo terminar de la manera adecuada para ayudar a minimizar los problemas que pueda tener más adelante. Gracias de nuevo.
I echo the last comment, really good job. thanks
Thank you and please subscribe, like and share if you you found it informative.
Thanks a lot for your easy advice way God blessed you ✅
We are glad you loved it. Subscribe for more
Nicely done. Thanks.
Thanks
Faboulas job Sir . i have learn about the athics of termination and dresssing ..
Hello Mohsin, It is always a pleasure to hear about how our videos have helped you learn something new. pls subscribe to the channel for more exciting videos
Hace décadas hacia este trabajo, con cable categoría tres que era básicamente cable multipar telefónico. Hice laburos para el banco mundial en Argentina. Me encanta el cableado estructural.
Hola Juan, espero que estés bien. Gracias por pasar y dejarnos una nota. siempre apreciado
no hay muchos canales que hablen del tema en español amigo, no estaria mal video de consejos
Great tuturial, I'm thinking of getting a patch-panel myself. But I don't agree with the wasteful use and then removal of zip-ties - better leave them on. It's less work, less waste, and it looks better - if you ever happen to be looking behind the patch-panel... :)
Hello waperboy, Thank you for the feedback. i hope it was informative
I think velcro that matches the color of the cables is the best look. Blue CAT VI, exact same blue velcro.
This is what we call it perfection
Samuel, Thank you for your feedback.
Thanks for the lesson Roland. Great job
Thanks.
Hope you found it informative. Don't forget to subscribe and turn on your notification for new videos
@@Delmitraining I liked and subscribed even before commenting bro. The video was very informative
@@richardennin4368 Thank you
that is a great job. Thanks for the tutorials
Thank you for watching and subscribing
Great tutorial!
Thank you for taking the time
Very neat work. Thank you for the explanation on how to keep the pair distribution the same length. My only question is why not route the second set to the other side so that no cables are running om top of the others? It seems like it would be better for troubleshooting later, especially if you had to terminate any cables on the first set.
Hello Darryl,
Thanks for reaching out. Ideally that is the best way to split and terminate the cables. However when you have cables coming in bundles of 24, it is a little bit tricky to split them above and ceiling route them that way. Take into consideration that there might be a switch between the panels. I am working on another video that explain this concept. Please stay tuned in for that. Thanks for subscribing and don't forget to turn on your notification
I'm new to learning IT. Exactly what job position will be handling things like you've shown in this video? I'm guessing, network admin? I would love to come to work and have to do things like this all day. So satisfying
This position would be a Network Cabling Specialist or Technician
Thank you for showing the 2nd way to strap and leave space to panel..nice and pretty but it would have been a night mare to replace or test the 1st cable terminated on panel with the other cables tightly terminated on top the middle.grouping and restrapping with space to access panel termination is ideal.
Hello Jaws, I am very glad you stopped by and left a note. that is very true. the first method is quite difficult to troubleshoot after the fact which make the 2nd part ideal. Glad you noticed the difference. Stay blessed wherever you are.
Well Explained!
Thank you for your tutorial man... subbed.
Hello Seven T, welcome to our channel. We are glad you stopped by and found it informative. Please stay tuned in as we will be posting videos frequently and also let us know if there are specific topics you would want us to cover. Thanks again
Thanks for your quality video
Thank you for sharing new supporters here
Hello and welcome to our channel. we are really excited you took the time to watch our video, we are also new to posting videos on RUclips and based on the feed back we are receiving, we will begin posting videos frequently. Please don't forget to like, share and subscribe so you would receive notifications of new videos we post. Thanks again
Very good video... Congratulations👍
Thank you my friend
good job except you should use a string to strip back the outer insulation
Great point. Sometime, not all cables come with the rip cord. Thanks for your observation
Wow! This is really neat.
Sounds like an Asian Mike Tyson
lol...
OMG that is sooooooo satisfactory tho! Nice video, nice job!
Thank you for taking time.
That's super clean. Are drip loops, or leaving serviceable lengths at the termination point an outdated standard?
You will not need a drip loop if your rack or cabinet has been bolted and the position will not change or move. It helps ensure that your terminations are clean.
excelente video, muchas gracias.
Hello Roland if I terminate 2 cables in the patch panel up and down, but only one cable runs to a keystone jack, how do I know which is going to work for the keystone jack?
Thank you for the question. i am not sure i understand 100% however i will try to answer it the way i understood it. Most patch panels will have numbers on the back where the cables are punched down corresponding to the numbers written on the front of the panel. they may also have the wiring scheme printed on the back to help guide you pick a desired scheme of your choice, A or B. At the user or the keystone end you must also terminate the cable using the wiring scheme you used to terminate on the panel. Keystone jacks can also accomodate for both the A and B wiring scheme so you will need to follow the chosen schem to ensure that you have a straight through termination on both ends. I hope i answered your question. let me know if you require additional information
Thanks a million!
All love!
I wonder if you can help me find a cable hook extraction tool like the yellow one you have. I've tried searching everywhere. Do you know who makes it and what the exact name is please? Thank you so much for your time and the fantastic video content.
Thank you for the comment and the subscription. The name of the tool is Probe Pic Tool. The one i used is made by Fluke networks. Here is the link to it on Amazon.ca. www.amazon.ca/Networks-44600000-Insulated-Pocket-Degrees/dp/B000FFRXEQ. You can search the internet and may get a better price. Good luck
Great job
Thanks
this looks soo neat,....can you please do one video with a 48 Patch Panel?
Hello Immanuel, please be on the look out. It will be posted. Thanks for subscribing and be sure to share our videos
Thank You
Greatly Appreciated
Hi,
Nice video! very simple and informative.
what are the tools did you use and where can I buy them?
Thanks for reaching out. I will put the description of all the tools that used in the description below. As always, thank you for stopping by.
Excellent...
Thank you
Dostum çakmaya 5-6 dan başlarsan diğer kablolar altta kalmaz ve daha güzel olur 👍 8:14
Thank you
Appreciated ❤🎉💯🔥
Thank you!
thanks a lot,
I don't even know what you are doing, I just like to look at organized cables.
i thought it was just me. videos like this giving me ideas how to tidy up my cables somehow. excellent job!
Thanks for taking the time to watch and share your feedback. We are always glad to hear from our viewers. Have a great day and don't forget to like, share and subscribe
@@morosso1968 Thank you for your feedback. this means a lot to us as we are also new to posting tutorial videos. we cannot do this without the support and feedback from you. we appreciate your time. we are creating more videos and please don't forget to like, share and subscribe. Stay safe!
@@Delmitraining who wouldn't like and subscribe a channel like this with a very good content. just keep your videos coming, you just don't know how much you help people like me . =)
@@morosso1968 Thank you once again. Your feedback inspires us to create and upload more educative contents. Please be on the lookout.
super neat
Thank you for watching, please be sure to subscribe and share
very nice bro
Hello Hamed. Thanks for stopping by.
My house has (15) builder-installed Cat5e T568A cables from 2007 and (8) Cat6 T568B cables that were added this year. When I run these Ethernet lines to my patch panel do I just wire them per there existing designations (T568A or T568B)? Does mixing different Ethernet cable types and wiring schemes create any problems? Thanks!
Thank you for reaching out. When you run the new Cat 6 cables to the Cat 5e patch panel, there are a few things to note. You are at liberty to have cables terminated as either 568A or 568B so long as both ends match. So having white green or green with white stripes as pin 1 and solid green as pin 2 etc. For 568A. When you have white orange or orange with white stripes as your pin 1 and solid orange as pin 2, this would indicate a 568B wiring scheme. Having 568A on one end of the cable and 568B on the other will create a crossover cable. If you are in the position to maintain one wiring scheme, our advice would be to stick to that to avoid future wiring mixups. Finally, termiating a Cat 6 cable on a Cat 5e patch panel will cause the cable to assume the characteristcs of a Cat 5e cable due to the thresholds set for Cat 5e. You will notice a lot of crosstalk at the patch panel. Thank you for reaching out once again and our apologies for the late response. Good luck
Great! Thx
Avelin, Thanks for stopping by to check us out and leaving a comment. means a lot to us.
Tip: Don't work over your cables like they show when terminating at the patch panel.
Rather get an inline patch panel. It reduces installation time by over 50%, nevermind that the this the chance of signal degradation, when.not installed properly.
Thanks for the feedback. i will post another video of terminating the cables directly on a patch panel on a rack
Very nice
Thank you
very niceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
Thanks for watching and subscribing
what are your thoughts on patch panels with keystone jacks. some dont even need to be punchdown
Keystone jacks are great and are generic, meaning that they are manufactured by many different vendors. My concern typically is who makes the one you might purchase and were they made of quality materials to meet the standard. We have used different types of keystone and some we have had problems with especially in areas of speed and crosstalk. For basics home networking, you shouldn't have any issue. Our advice, however, is to find a reliable distributor if you need them for other data or mission critical purposes. Good luck, and sorry for the late response
can i use this patch panel with two different isp provider at my home setup? thanks
Hello AJ, Thank you for reaching out. If I understand your question well, then the answer is yes. The patch panel can be used to service any interner provider. Remember that the patch panel is where all the cables from multiple user locations terminate. So if you have two or more providers, you can terminate them both on the panel. The most important thing is to make sure that, you maintain the same termination standard (568A or 568B) at both ends and remember to label the terminated ports with the appropriate names or designation. I hope this answers your question. Have a great day!
WHY is it that telecom guys have such bad lacing skills. Except for at the end that was pretty good dressing!
or just use a keystone patch panel. it’s faster, takes up less room, and is much easier to repair should a port go out.
Hello samuel_the_Pro, thank you visiting our channel and your feedback. It is always great to hear from everyone. We will soon be posting a video on using a keystone unloaded patch panel which is faster just as you mentioned. Please don't forget to subscribe, like and share our videos and also turn on your notification to be notified of our new videos. Thanks again. Really appreciated
or just pei tu oder tu du da llob!
moch simpler!
Like
que pasa si un hembra esta dañado, o un cable? tremendo problema sacar todo eso
Hola Ricardo, y gracias por haber contactado con nosotros. Es una pregunta muy buena y práctica. Hay casos en los que el bloque de terminales se daña durante la perforación. cuando esto sucede, lamentablemente, tendrá que reemplazar todo el panel o marcar ese puerto específico como defectuoso para que el cliente sepa que no debe usarlo. debido a casos como ese, prefiero usar los paneles de conexión sin carga.
Video is scrambled on my end
Hello Abdulazeez, sorry you are experiencing technical difficulties, try using the link below and hopefully it will work for you. ruclips.net/user/delmitraininginstitute
Please dont forget to subscribe, like and share our videos.
Or use 1 optic fiber and router :)
Hello K kaolin, that is true as well to use optical fiber and router. The cost and distance must be taken into account
why you chose A Why not B???
Hello Mohamed, thank you for reaching out. It really doesn't matter which of the termination standards you choose to adopt. The key though is to make sure that both ends follow the same pinout configuration. I live in Canada and majority of the terminations ae done conforming to the 568A pilot configuration. I will achieve the same results if I were to use the 568B for the video. Hope this answers your question. I hope you have a great day!
ногти надо подстричь ))
Thanks will trim them in the next video
FIRST NO ONE terminated patch panel as 568A anymore unless you are working on a PBX system. second leaving that much open wire behind the punch is against code
Hello, thank you for stopping by. I live in Canada and we do a lot of 568A terminations. Our neighbors down south, the Americans do a lot of 568B wiring. As per TIA, you are at liberty to use any of the two wiring schemes as long as both ends are the same for a straight through connection. Also, the notion of 568A used only for PBX is incorrect. It might have been widely used in the past for such purposes however, i am aware of many other jurisdictions around the world that still use 568A scheme.
Now to your second question, Cat 5e cables are known to have a less twist ratio per inch. When terminating them, you may experience a wider gap expecially on the blue pair due to this reason, and this explains why there is so much crosstalk at the panel. Thanks for the learning opportunity. Have a great day!
Thanks everyone for your kind words! You can meet Professor Alli explain more here: ruclips.net/video/NovXCrcoiII/видео.html
Just use B NOT A
First off.... why isn't the panel in the rack ? You cutting down on a table???? Looks like absolute garbage
Thank you for reaching out. We decided to terminate on the table to explain the process. if you want to see how we terminate on the patch panel in a rack, check out our other videos. ruclips.net/video/Tw9dPwFy9AA/видео.html. Once you are done, show us your work as well so we may learn from you. Thanks
Fu.......k of how much cable just cutted off and wasted🤦♂️
Hello Antonio Arizo, Thanks for watching our video. unfortunately, there are no wastage of cables because any excess cables that were cut off were recycled. This is the correct method to have your cables terminated onto a patch panel. It is always better to have an extra foot of cable than to have an inch short. It is very important not to dispose of copper cabling without properly recycling them. We are very fortunate to have facilities that would recycle and reuse the cables that we scrap. We would be glad if you have a better method of terminating patch panels as we would love to learn from you. Thank you once again
no gounding? no shielding? what is this crap for?
Hello Computer Service Slovakia, Thanks for reaching out. This video is a tutorial on how to properly terminate an unshielded twisted pair cables onto a loaded patch panel. Grounding is an important part of the design of any network closet. TIA, ISO and CENELEC have recommendations regarding the proper steps required for grounding and bonding. Even though they have their recommendation, they always recommend to consult the local fire codes bases on your jurisdiction. In every network closet, grounding is an important part of the overall design and the network rack or cabinet must always be properly grounded. When terminating UTP cables on an unshielded panel, there is no need to ground the individual patch panel because the rack or cabinet should have already been grounded. The situation is different when working with shielded cables. with regards to shielded cables, each shielded patch panel must be individually grounded to help dissipate all unwanted noise to ground. if you have any specific concerns, please let us know and we will address it.
@@Delmitraining who uses unshielded cables this time?
Hello again, since this is a channel dedicated to sharing knowledge, I will take this opportunity to educate you. There are different categories of cables available on the market today right up from Cat 5e to Cat 8. All these cables have different frequencies to which the operate. The higher their frequencies the more bandwidth they have and this also increases the data transfer rate. There are additional factors to this such as the amount of twist per inch of each of the pairs to help eliminate crosstalk and also the cable gauge used. Most network applications in today's use require speeds of up to 1Gbps. Unshielded Cat 5e and Cat 6 cables are designed to support such speeds in environments with little to no interference which is our every day life application when the cabling is installed and supported properly up to 100 meters, 300ft. Unshielded Cat 6A supports speeds up to 10Gbps and is backward compatible with Cat 5e and Cat 6. Bear in mind that most network equipment in our day to day use does not support this speed. Such speeds are required in areas where high bandwidth application are required such as data centers etc. Cat 7 to 8 are designed to support speeds of up to 40Gbps. To achieve this speed their construction must include Shielding of the individual pairs and an overall braiding with an increased cable gauge. Even with all these added bells and whistles, the max channel length is 30 meters for 40Gbps and 10Gbps at 100 meters.
Now, when working in areas with high interfering sources such as factories with lots of RF generating sources or applications for Audio Visual, Shielded cable is recommended and the category of the cable depends on the desired speed
So now I hope you understand why UTP cables are the preferred cable for every day applications. Thank you for reading and don't forget to subscribe, like and share our videos
Like