This was very helpful in the order of removing components. Very glad you showed it going back together! Many instructionals just tell you to reverse order. To me the assembly was just as helpful as the disassembly and I was able to successfully repair mine from random reboots caused by bad flex ribbon. The only thing I would add for first timers is to organize screws so you know exactly what screw goes back where. Also pay attention to the little details in the video such as the top corner (near camera) of the motherboard sliding back underneath the bracket in order for it to sit flat. Those little details are often crucial to a successful repair. My repair part came from ifixit and appears to have been a used one, perhaps all these type of parts have to come from donor phones.. It works and being used I feel reasonably assured its genuine but I don't recall the listing stating so.
Hi! Thanks for the video! I had panic error on mic1, so I did replace the charging flex cable and port on my iphone SE 2 but it gave me mixed signals: first it was still restarting every three minutes, then it worked with no restart for more than an hour, then restarts and then every three minutes again, then works for 30 mins, then restarting every three minutes again. I havent done anything particular to it in the meanwhile. Would you have any next step to advise to sort this out? Thank you
@@DIYGeardo u remove the old part and then put the new iphone chargeing port ....i want to know the new changeing port brand name...is it 3rd party charging port ???
@Sakis Nikitaras Does your charge port work? I saw a video and if your charge port is bad it causes it to reboot every 3 minutes. Mine does not charge thru port, only wireless. I will let you know.
will i lose my data if i get it fixed like this by someone else? need serious help as I have not backed up my phone in long and will lose many photos if that's the case
I mean by replacing the charging port you won’t loose any data. But if someone damage to the board then there will be an issue. But that is very rare. Also you can use a wireless charger to charge the phone to backup the data.
Yeah there’s no left side speaker. Once they put the aux port on that side with the iPhone 5 that was the dead giveaway for me, if you haven’t already looked it up.
Well always good to have a heat gun.Sometimes you will need to soften the adhesive. You can use to soften the charging port flex adhesive. It is is not a must, but good to have it.
Hi thanks very much for a very informative Video. I was wondering if you could help me with this problem. I have a iPhone SE 2020 there is a small square bracket on the main logic board between the board and the tapic engine. I would like to know its function, there is an electrical contact point on it but it doesn’t seem to touch ground or any other electrical point. there is a ribbon from the charging port that sits on the tapic engine then this bracket sits on top and then it is screwed into place Could you please enlighten me….thanks in advance Cliff
Dam Idk.. I did a screen replacement in my old iPhone 5 and it was a little something something to it.. to make it easier I left me thumbprint reader in the broken screen just to save one step.. this one seem a little much… like he just kept taking stuff out amd taking stuff out….. and this is my main phone… I would be more inclined if I was already into a new phone and there wasn’t much consequence..
Dam Idk.. I did a screen replacement in my old iPhone 5 and it was a little something something to it.. to make it easier I left me thumbprint reader in the broken screen just to save one step.. this one seem a little much… like he just kept taking stuff out amd taking stuff out….. and this is my main phone… I would be more inclined if I was already into a new phone and there wasn’t much consequence..
I took it to shop and they checked it and was not drawing any amperage. I checked battery with multimeter and it was dead. Ordered new battery from Amazon. Hoping for the good.
Yes you do!!!! Otherwise, how the hell are you gonna peel the lightning connector flex board unit from the chassis. The motherboard sits right on top of the lighting port unit. Rewatch the video & learn.
This was very helpful in the order of removing components. Very glad you showed it going back together! Many instructionals just tell you to reverse order. To me the assembly was just as helpful as the disassembly and I was able to successfully repair mine from random reboots caused by bad flex ribbon. The only thing I would add for first timers is to organize screws so you know exactly what screw goes back where. Also pay attention to the little details in the video such as the top corner (near camera) of the motherboard sliding back underneath the bracket in order for it to sit flat. Those little details are often crucial to a successful repair. My repair part came from ifixit and appears to have been a used one, perhaps all these type of parts have to come from donor phones.. It works and being used I feel reasonably assured its genuine but I don't recall the listing stating so.
Thanks for your detail feedback...
Hi, why does the camera and other parts at top need to be removed to replace port?
Thanks for the video! I just fixed my phone 👌👌
Glad I could help!
Hi! Thanks for the video! I had panic error on mic1, so I did replace the charging flex cable and port on my iphone SE 2 but it gave me mixed signals: first it was still restarting every three minutes, then it worked with no restart for more than an hour, then restarts and then every three minutes again, then works for 30 mins, then restarting every three minutes again. I havent done anything particular to it in the meanwhile. Would you have any next step to advise to sort this out? Thank you
For me is the same lol did you find any solution¿
Great Video Thank you! My phone did not immediatly turn back on after the repair but i plugged it in and it turned on after that.
Great to hear! 🙏
Great step by step replaced mine and all good 👌
Good to hear
This video saved me! Thank you.
Great 🙏
What brand what chargeing port i should buy ? I mean what brand and name of the new changeing port ?
Please ans it will help me a lot
You mean the cable or actual part?
@@DIYGeardo u remove the old part and then put the new iphone chargeing port ....i want to know the new changeing port brand name...is it 3rd party charging port ???
@@sundaylover7786 there is no brand name for parts, there is original, used or aftermarket ones..your location? The one we replaced was an original
@@DIYGeardo ohhh sir.. i am from India....can u suggest me any 3rd party good chargeing port for apple se 2020..
I want to replace it
Hello i need help, my phone starts rebooting and overheating after i replaced the port
Hello, this works for the 3 minute reboot problem?
Did you do any repairs recently?
Same for me even after 6 different docks I have problem and keep restarting after 3 minutes
You replaced you charge port and problem went away?
@@mgomez5606 For me nothing fixed my issue so I stopped trying
@Sakis Nikitaras Does your charge port work? I saw a video and if your charge port is bad it causes it to reboot every 3 minutes. Mine does not charge thru port, only wireless. I will let you know.
Do I need to remove the microphone off the old board/flex how does it come with Microphone my microphone is not working
It’s on the charging port flex, best option is to change the charging port flex
Its the same part charge with ip 8?
will i lose my data if i get it fixed like this by someone else? need serious help as I have not backed up my phone in long and will lose many photos if that's the case
I mean by replacing the charging port you won’t loose any data. But if someone damage to the board then there will be an issue. But that is very rare. Also you can use a wireless charger to charge the phone to backup the data.
It’s ok I see another video they manage to slide new part under logic board. Still your video good thanks very informative.
No problem 👍different ways are there
my iphone se(2020) keeps restarting every 2-3min after new charging flex. please help
Means your charging port have issues. You need to try another one. This is most likely issue.
Não é original?
Are the screws all the same size?
No, not same
Sir, will I get any errors on phone for replacing charge port?
Nope
@@DIYGeardo Geardo, when you replace battery. How do you reset battery health on this phone?
@@mgomez5606 for that you need to place the old battery board, if not a genuine battery
@@DIYGeardo what if I just replace battery. What messages will I get, Geardo?
The speaker buzzer , it only works on right side when facing front screen ? Because no sound coming from left side
Yeah there’s no left side speaker. Once they put the aux port on that side with the iPhone 5 that was the dead giveaway for me, if you haven’t already looked it up.
@@christianmichael4020 ip7 had a speaker on left im surprised se only has one
Do you need the heat gun for this replacement? Not seeing it used in the video unless I'm missing something?
Well always good to have a heat gun.Sometimes you will need to soften the adhesive. You can use to soften the charging port flex adhesive. It is is not a must, but good to have it.
Hi thanks very much for a very informative Video.
I was wondering if you could help me with this problem.
I have a iPhone SE 2020 there is a small square bracket on the main logic board between the board and the tapic engine.
I would like to know its function, there is an electrical contact point on it but it doesn’t seem to touch ground or any other electrical point.
there is a ribbon from the charging port that sits on the tapic engine then this bracket sits on top and then it is screwed into place
Could you please enlighten me….thanks in advance Cliff
Is there any way you can send us a photo
Before I try this is there a chance I can be locked out from my phone?
What do you mean by locked out?
Worked! amazing.Thnaks
Great.. Welcome
Dam Idk.. I did a screen replacement in my old iPhone 5 and it was a little something something to it.. to make it easier I left me thumbprint reader in the broken screen just to save one step.. this one seem a little much… like he just kept taking stuff out amd taking stuff out….. and this is my main phone… I would be more inclined if I was already into a new phone and there wasn’t much consequence..
Top screw on plate near Taptic Engine is a type none of these tools fit
Can I replace with a non OEM charging port flex
Yeah
Suggest me a charging port
Thanks
You are welcome 🙏
very clearly explained thx
Thank you 🙏
6:20 son of a gonna i pull the tab right above the flex and broke it what is that for . should i even finish. or did i facked up my phone.
I think you broken the charging port connector? what is the part you are trying to replace?
How much does it cost bro
About $20-30
Dam Idk.. I did a screen replacement in my old iPhone 5 and it was a little something something to it.. to make it easier I left me thumbprint reader in the broken screen just to save one step.. this one seem a little much… like he just kept taking stuff out amd taking stuff out….. and this is my main phone… I would be more inclined if I was already into a new phone and there wasn’t much consequence..
Replaced the charge port and now it don't come on or charge. Not even wirelessly it won't charge
I took it to shop and they checked it and was not drawing any amperage. I checked battery with multimeter and it was dead. Ordered new battery from Amazon. Hoping for the good.
Removing the logic board is unnecessary
me sobraron tornillos
You don’t have to remove the logic board to replace the charging port and mic. This is a tortuous guide
Yes you do!!!! Otherwise, how the hell are you gonna peel the lightning connector flex board unit from the chassis. The motherboard sits right on top of the lighting port unit. Rewatch the video & learn.
so broke my iphone😅
What do you mean?
Hi
🖐
Insta id ? Sir !