Sheet Metal Embossing Process Animation Tutorial in Solidworks

Full Tutorial in Solidworks : Sheet Metal Embossing Process Animation
This Tutorial Consists of:
1. Die & Punch Design
2. Assembly
3. Animation
This is Just a Model Animation.
Some Other Sheet Metal Process Animation Tutorials:
1. Blanking Process Animation Tutorial Solidworks
• Blanking Process Anima...
2. Sheet Metal U Bending Animation Tutorial Solidworks
• Sheet Metal U Bending ...
3. Sheet Metal Edge/Wipe Bending Animation Tutorial Solidworks
• Sheet Metal Edge or Wi...
4. Sheet Metal V Bending Animation Tutorial Solidworks
• Sheet Metal V Bending ...
Embossing:
It is a Metal Forming Process for Producing raised or sunken designs in sheet metal material by means of matched male and female dies.
Hope You Liked it.
Do Like Subscribe & Share.
Stay Connected For More Such Tutorials.
Do Share Your Opinion in the Comment.
Thanks for Watching.

[@kathireshmurugan3584]

Sir useful This disign 🇮🇳

[@SolidworksFunPraveenSingh]

Thanks!

[@AJ_quotes_facts]

If you make a voice over it will more understable for viewer

[@rusu959]

nope. he gave essential details, enough to repeat his steps. you just have to pay more attention to understand. thanks!

[@ML.ArtificialIntelligence]

is there any other way to do this task because this one is so much time taking and cannot able to perform analysis on it

[@SolidworksFunPraveenSingh]

this is just for animation.
on the channel, there is another Tutorial on 2d nonlinear stress analysis of embossing operation.
you can watch that!

[@theemperor4846]

When i unsupress the distance my bar is not getting straight sir please help me i need it please 🙏🙏🙏🙏🙏🙏🙏

[@SolidworksFunPraveenSingh]

can you point out the time where this happens?

[@theemperor4846]

@@SolidworksFunPraveenSingh 11:42

[@SolidworksFunPraveenSingh]

Try Recreating the Distance Mate and New Part Design (the crucial steps) in a new Assembly.
7:48 distance mate creation
9:08 new part design
10:15 very crucial step (some sketch of New part will be made coincident with the Punch part, this will create Embossing possible if punch will be sent down by Adjusting the Distance Mate values)
10:37 is also a very important step
Hope this may solve the problem.

[@theemperor4846]

@@SolidworksFunPraveenSingh Sir i had already tried it 6 to 7 time but everytime i stuck with same 2 problems
1. At 10:02 my smart dimension shows 'you cannot select reference from outside modal' when i try to give distance between die and new part
2. I had mentioned it earlier
Sir please help me i need to make this
Is there any other platform at which i can contact you so that i can make the video of my problem and give it to you.
Please help me sir 🙏🙏

[@theemperor4846]

@@SolidworksFunPraveenSingh sir this accout require premium membership to message

[@deepaanandhan9790]

Is I able to do this in catia ?

[@SolidworksFunPraveenSingh]

possibly yes!
give a try.

[@deepaanandhan9790]

@@SolidworksFunPraveenSingh bro is able to do that animation in fusion 360

[@SolidworksFunPraveenSingh]

actually i don't have that software But if you have then give a try.The features used in this tutorial may be there in Fusion 360 also.

[@deepaanandhan9790]

@@SolidworksFunPraveenSingh I have a try .And tell you bro

[@SolidworksFunPraveenSingh]

the features used to create this Animation are very common, so there should not be any problem if you try to create in any other CAD Software.