TILT and TRIM Installed on Small OUTBOARD Jon Boat BUILD

I installed a Bobs Machine Tilt and Trim onto my small 15hp Johnson outboard. Everything I did on this installation is in this video. Looking forward to a top speed run and seeing just how this little 14 foot Jon boat maneuver at high and low speeds! As always Thanks For Watching!
Previous Boat Videos:
• Replacing TILLER with ...
• Throttle and GEAR Shif...
• Jon Boat SUSPENSION Se...
• Jon Boat Aluminum FRON...
• FIRST RIP on my TINY B...
• Electric CHOKE and STA...
• Flooring.. Trolling Mo...
‪@kentuckyyankee‬
#tiltandtrim #outboard #jonboat

[@robertwright1083]

You did a great job and also in making this video. thank you, I'm saved for solving my problem.

[@robertlawson1184]

Well since you took out the mount locking tabs, might as well drill a bigger hole on the stud eyelet and stick a rod to lock it from spinning off.

[@darthjar9117]

Stainless steel lock nuts were too expensive?

[@samueldoyle1656]

Stainless makes aluminum corroed faster

[@larrybalowski946]

Great job

[@philwalden6166]

A nice video, but I did not see the tilt trim assembly be installed which was the very most important.

[@eamonnocarroll5866]

Thanks

[@PaulyV56]

nice
work!

[@kentuckyyankee]

Thanks! I'm gonna lower the engine 1 inch I think it will preform better stay tuned.

[@chadbosko8935]

Looks like i have the same unit to install and directions mention nothing about the height you put yours flush at the front isnt that going to raise your motor much to high and it wont run right. Watching the end of your video, the motor looks a lot higher than the transom how did the motor work like that?

[@KimNguyen-or3tt]

good job buddy ! i would like to have that for my 20 hp honda some time,

[@kentuckyyankee]

I like the trim but as far as performance not much advantage as far as I can tell.

[@alexopweg]

Nice job . How much does it cost please???

[@jacobmorris9830]

Is your motor a long shaft? I have a short shaft transom and motor and am wondering if this acts as a Jack plate or can I continue to run the short shaft with this unit

[@garlandhood9729]

Do you still have this boat I have same set up but my boat is a 12 foot boat with those beaver tail aluminum pods welded on back it does very good it ran bout 35 mph with just me after pods welded on it slowed down bout 5 mph. Yell back at me

[@kentuckyyankee]

I sold this one awhile back. It was fun while I had it.

[@JupiterGeorgeFishing]

Not trying to be an ass but if you ever hit anything the engine won't pop up now because of the way you locked it in with that piece. Just be careful about that...

[@tieoneon1614]

That seems to be a southern'r issue. Us Yankee's dont hit stuff with our power trim cuz we trim up in shallow water.

[@jayward7536]

Nice but overkill for a 15 hp. And the thru transom bolt holes should be filled with sealer just saying

[@justchipsfishing8951]

Hi mate. Do you have a link to purchase one of these? My 30hp merc needs one asap hahaha

[@kentuckyyankee]

Google Bob's Machine tilt and trim, there will be many options.

[@justchipsfishing8951]

@@kentuckyyankee thanks mate

[@asherevan3335]

Hi grandpa🙂

[@kentuckyyankee]

Hello!! 😀

[@scottkeefe2236]

How much was that tilt and trim plate

[@kentuckyyankee]

$700

[@user-um9ri4yx2i]

Where can I get one

[@brianpenrod8493]

Lol!

[@jackrutherford-1]

Rip it!

[@kentuckyyankee]

Will do!!