Great Video! 😀 Appreciate your hard work to make it with all the illustrations. Thank You! I ordered one (6M, I think?) and will use your video and methodology to get it running.
The Latitude and Longitude separated by the comma can be copied and then pasted directly into Google Maps' Search here line. Then you can see how accurate your GPS is. Great vid.
I have the GPS module with the buit-in ceramic antenna and the SMA connecter for external antenna. Is the external antenna detected and the device switches to the appropriate antenna or some capacitor/resistance need to be removed/added? I'm asking because mine works well with the external antenna but very poorly with the built-in antenna (I'm comparing the to similar devices with ceramic antenna only).
Hi, generally you need to remove or add something to establish connection to the new antenna. Wherever you purchased it three should provide you the details or just do an image search using bing or google, I am sure you will find information for that.
I'm getting nothing but blank GPS data, like that shown in the begging of this video. Does that code do any writing to configure the GPS device before it will work correctly?
everything you need to do is shown in the video. you may not be receiving GPS signal. try a better location exposed to sky. if you are located above the equator, then point it to south-up and if you are below the equator, then point it to north-up
@@robojax Thank you. I did try that. We're standing away from buildings and trees, but I still don't get anything after 5 whole minutes. Do I need to give it more time than that to lock in a signal?
Hi, I'm just wondering, do you have to use the RX pin on the GPS module? What does the RX pin do exactly, like what does the gps need to get from arduino
Hi, GPS module has a lot of parameters that can be set with the library including the refresh rate(very important) and other which we are not concerted with. I have another video that you can get coordinates without library. The link is in the description of this video.
Thank you for your video. I try to find information how to logging nmea data when push button on my photocamera. I wanna make very correct GPS data only when camera makes shoots
how accurate your GPS is ? Description 3m - real about 3m - outside - Max read working speed about 1 sec - satellites move so you get +/- 5 m - good idea to calculate average for 10 results ( the best calculate during 90 sec )
hii thank you for explaining this. this video was very good and useful. Then i have a question. can i use that location numbers to see my location on my phone.
this can give you the location. It is up to you whatever you want to do with it. Perhaps one way would be to use Bluetooth or WiFi to send it to your phone. You will need module for that and then you will need an app to make it work. search for "bluetooth" on my channel and see if I have something you can use.
I have neo-8m gps module. The baud rate on that one is 115200. The UNO seems to be just too slow for that. Plus the TinyGPS library wouldn't work for newer generations. I'm still trying to get it to work. I found out neogps library should work with it. The problem is too many crc errors. Any hints?
Hi sir, thank you for the video. I did follow the steps that you've shown in the video, but I cannot obtain any output in my serial monitor. I'm using gps 6m, aduino uno and I also put the gps besides my window. But still, there is no gps signal. Can you help me please.
other than telling you to check wiring and library and making sure your Serial monitor is set at correct baud rate, I can't see problem. snag.gy/y3pKwG.jpg
Hey! I have some questions: - Can I use Neo-6 or Neo-7 for indoor purposes? If yes, how much can the module be obstructed? (I mean using the module under a roof, or into low floors in a building).
I have two Neo-6 modules that works in the house (in a plastic box, for protection)(ceramic antenna), at 1st or 2nd floor, but an other that only works outside. Sometimes it seems to be very sensitiv, or can the 3.15GHz go through the windows ?
Is the antenna comes with the gps module itself or we have to buy it seperately? and Is the same code explained above works for the Neo 7m GPS modules?
It depends on the seller. When you purchase they will mention. In the video I have explained it which one is coming with the antenna but I forgot. You have to watch it if you want to know.
Hello... I am using GPS neo 7m and it shows the correct longitude and latitude in the serial monitor, but it shows the wrong time... how can I correct it??
Hello sir, thank you for your video. I would like to ask you something about my final project. Its the combination of data fusion between GPS and IMU can enhance the accuracy of the user/object. So which arduino compatible with both of them?
Hello I am interested in your project can you just share how you did your project? Maybe from Github. Actually I wanted to used two GPS modules simultaneously for more accurate positioning
You are welcome. The best thank you for me is to subscribe to my channel. Your subscription is stamp of approval and my videos will be suggested to more people and this will help me. I appreciate it. thanks❤️
Hello, we define object for each device. In GPS I just checked we have "ss" as object. you can learn it from this LCD example ruclips.net/video/L6ekl2ABcuY/видео.html
Hello Robojax I have trouble can you help me ? problem: I use 8266 to scan Wi-Fi and using neo -7m. scan Wi-Fi locations Do you think this can be done?
Hello, I've not tested the library with this module. You may use the code shown in this video so you can get location without library ruclips.net/video/rCXYP6H3gSE/видео.html and WiFi scan can be done at the same time. Good luck
Thank you for the video. I can send the gps data signal from arduino to my cell phone but is it possible to use that data to get a live pin to a map, without updating all the time? (Maybe with an app or a website?) Thank you very much for your time.
You are welcome. Yes it is possible but it needs a service. I have a plan to create such service but it is a lot of work. You find Amazon AWS free service that takes data from GPS from Arduino and your app can connect to the service. Search Amazon AWS.
Hello, Is it possible to get the gps coordinares of a particular location if the value of a sensor exceeds its threshold(which i give in code)? Thanks in advance!
You are welcome. The best thank you for me is to subscribe to my channel and thumb up the video. It is greatly appreciated. 🔔 😊. You haven't subscribed yet. will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊
Big time quiestion, that's driving me crazy. Why on Earth does it has an RX pin. Can someone help? Can I send Data to the GPS Module? I am talking Commands to read a specfic NMEA Sentence
Yes you can send and set parameters including power and sleep mode. Read the datasheet and if you figure it, you can control it. This video is about extracting location.
No GPS detected: check wiring I've gone over the wiring multiple times, checking for connections and everything seems fine, could it be that the GPS is broken?
Hi, I am not sure. Try my code from this video ruclips.net/video/rCXYP6H3gSE/видео.html and if GPS can see sky towards equator, then GPS module is bad.
I don't remember what I said in the video. if I mentioned to select the model, then do it. if not then it means the same code work. Here is another video on GPS so you can use it without library and I have explained it so you can get location ruclips.net/video/rCXYP6H3gSE/видео.html
Thanks for sharing this video. i have tried neo7m0000 beside the window for long time but the data stay same $GPGSA,A,1,,,,,,,,,,,,,99.99,99.99,99.99*30 and never change and the light doesn't blink. even before i tried neo6m it worked two times outside then stop for ever. i am no sure what is the issue with gps. can you help
Hello, so check the wiring. First test your code without connecting the GPS module. if you are getting the same data, then it means GPS is not receiving or sending data to Arduino. Also have you checked this video which very simple without library: ruclips.net/video/rCXYP6H3gSE/видео.html
Wherever you put them, they must get signal. Signal can't reach if antenna is covered with metal. so you may put antenna outside like a small wire that can can see sky.
Hello Sir, I have uploaded the code successfully on the board just as how you instructed in the video. However, it still shows in the serial monitor that the location is invalid though I went near the window and the neo 6m started blinking. What could possibly be the problem?
when it prints it on serial monitor, that is USB. just read it. Arduino is reading it from USB and printing it for you, now you do your job to get in your Window/Linux/Mac machine to read it outside Arduino. if that s what you want.
what about we want to get signal from 2 gps? i mean, i have 2 gps and i want to get signals from them with 1 antenna which connecting to my pc. Is it possible that get signals from 2 gps with 1 antenna at the same time?
In the description of the video, I have link to the page on Robojax.com where you can get the code. The datasheet is provide in the same page where I put the code robojax.com/learn/arduino/?vid=robojax_GPS_TinyGPSPlus
Neo 7m has more accuracy and faster refresh rate. here is the official page foe Neo-6m www.u-blox.com/en/product/neo-6-series and Neo-7m www.u-blox.com/en/product/neo-7-series
Hi, thanks for sharing your knowledge I ran the program and the gps displays INVALID, date 00/00/000, time 00:00 gps.location.isValid() return INVALID Location: INVALID Date/Time: 0/0/2000 00:00:00.00 Location: INVALID Date/Time: 0/0/2000 00:00:00.00 Location: INVALID Date/Time: 0/0/2000 00:00:00.00 Can you tell for what reason? Tks !!!! Bruno
@@robojax I saw the datasheet of the ublox core, but I wanted the datasheet of the entire module itself, I can't, right? I've tried to find it on Google but it doesn't have
you won't find it. this module-with-pcb even doesn't have a model number. someone just produced it and assumed you use the main datasheet. Besides it has very few components which you can search online for each and know what they are. Good luck.
Many little errors and shortcut text in this video. You say connect to pin2, but plug a wire into what is labelled D1. You talk about the Serial Monitor connection, when the statements you refer to are for the software serial connection, which is what communicates with the GPS. Then 'connect Tx on the GPS to rx', but omit the additional words 'on the Arduino'. Kind of misleading. Difficult to give it a thumbs up.
Than you for your comment. I appreciate it. I am not sure if you are familiar with Arduino, in this context which we get the data using Arduino board, Serial Monitor is within Arduino an pin2 is also refers to pin 2 of Arduino. I will read the errors in text. The title of the video is the words "in Arduino". I am sorry if you felt mislead. But greatly appreciate your comment.
Great Video! 😀 Appreciate your hard work to make it with all the illustrations. Thank You!
I ordered one (6M, I think?) and will use your video and methodology to get it running.
The Latitude and Longitude separated by the comma can be copied and then pasted directly into Google Maps' Search here line. Then you can see how accurate your GPS is. Great vid.
Thanks.
Hi Nice video, can your code work with NEO-6M GPS? cos your video show others GPS i dun know if its NEO-7, please advise ? thx.
hiii..iam getting no location found and THIS CODE IS ONLY FOR ublox or could we use this for any other devices..?...iam using sim28ml module
I have the GPS module with the buit-in ceramic antenna and the SMA connecter for external antenna. Is the external antenna detected and the device switches to the appropriate antenna or some capacitor/resistance need to be removed/added? I'm asking because mine works well with the external antenna but very poorly with the built-in antenna (I'm comparing the to similar devices with ceramic antenna only).
Hi, generally you need to remove or add something to establish connection to the new antenna. Wherever you purchased it three should provide you the details or just do an image search using bing or google, I am sure you will find information for that.
Thank dude. I got it to work !!!
Glad I could help
I'm getting nothing but blank GPS data, like that shown in the begging of this video. Does that code do any writing to configure the GPS device before it will work correctly?
everything you need to do is shown in the video. you may not be receiving GPS signal. try a better location exposed to sky. if you are located above the equator, then point it to south-up and if you are below the equator, then point it to north-up
@@robojax Thank you. I did try that. We're standing away from buildings and trees, but I still don't get anything after 5 whole minutes. Do I need to give it more time than that to lock in a signal?
no. 5min is enough. something is wrong. Try method shown in this video ruclips.net/video/rCXYP6H3gSE/видео.html
Hi, I'm just wondering, do you have to use the RX pin on the GPS module? What does the RX pin do exactly, like what does the gps need to get from arduino
Hi, GPS module has a lot of parameters that can be set with the library including the refresh rate(very important) and other which we are not concerted with. I have another video that you can get coordinates without library. The link is in the description of this video.
@@robojax Is it this video? ruclips.net/video/rCXYP6H3gSE/видео.html
Thank you for your video. I try to find information how to logging nmea data when push button on my photocamera. I wanna make very correct GPS data only when camera makes shoots
You are welcome. This code can be used for that purpose.
how accurate your GPS is ? Description 3m - real about 3m - outside - Max read working speed about 1 sec - satellites move so you get +/- 5 m - good idea to calculate average for 10 results ( the best calculate during 90 sec )
Just check the datasheet and don’t trust what I say.
hii thank you for explaining this. this video was very good and useful. Then i have a question.
can i use that location numbers to see my location on my phone.
this can give you the location. It is up to you whatever you want to do with it. Perhaps one way would be to use Bluetooth or WiFi to send it to your phone. You will need module for that and then you will need an app to make it work. search for "bluetooth" on my channel and see if I have something you can use.
I have neo-8m gps module. The baud rate on that one is 115200. The UNO seems to be just too slow for that. Plus the TinyGPS library wouldn't work for newer generations. I'm still trying to get it to work. I found out neogps library should work with it. The problem is too many crc errors. Any hints?
Hi sir, thank you for the video. I did follow the steps that you've shown in the video, but I cannot obtain any output in my serial monitor. I'm using gps 6m, aduino uno and I also put the gps besides my window. But still, there is no gps signal. Can you help me please.
other than telling you to check wiring and library and making sure your Serial monitor is set at correct baud rate, I can't see problem. snag.gy/y3pKwG.jpg
Hey! I have some questions:
- Can I use Neo-6 or Neo-7 for indoor purposes?
If yes, how much can the module be obstructed? (I mean using the module under a roof, or into low floors in a building).
No you can't . It needs direct view of sky to receive signals.
It's a late answer but, I believe that installing an external antenna will work!
I have two Neo-6 modules that works in the house (in a plastic box, for protection)(ceramic antenna), at 1st or 2nd floor, but an other that only works outside. Sometimes it seems to be very sensitiv, or can the 3.15GHz go through the windows ?
It says gps detected: check wiring but my wiring and battery is good does that mean the module is faulty or busted ?
Is the antenna comes with the gps module itself or we have to buy it seperately? and Is the same code explained above works for the Neo 7m GPS modules?
It depends on the seller. When you purchase they will mention. In the video I have explained it which one is coming with the antenna but I forgot. You have to watch it if you want to know.
Thank you
Hello... I am using GPS neo 7m and it shows the correct longitude and latitude in the serial monitor, but it shows the wrong time... how can I correct it??
Hello, it is because you are reading GMT. You need to add or subtract your time zone. learn about time zone.
Hello sir, thank you for your video. I would like to ask you something about my final project. Its the combination of data fusion between GPS and IMU can enhance the accuracy of the user/object. So which arduino compatible with both of them?
Hi, You are welcome.I don't know what IMU is.
@@robojax IMU is a sensor. To make the gps more accurate we can use imu sensor. Btw thanks for your reply
Hello I am interested in your project can you just share how you did your project? Maybe from Github. Actually I wanted to used two GPS modules simultaneously for more accurate positioning
Very helpful. Thank you.
You are welcome. The best thank you for me is to subscribe to my channel. Your subscription is stamp of approval and my videos will be suggested to more people and this will help me. I appreciate it. thanks❤️
Hello Sir can I use multiple GPS modules simultaneously with the same Arduino? How?
Hello, we define object for each device. In GPS I just checked we have "ss" as object. you can learn it from this LCD example ruclips.net/video/L6ekl2ABcuY/видео.html
I didn't notice but, is it 3.3v powered? Does not accept 5v?
yes
Hello Robojax I have trouble
can you help me ?
problem: I use 8266 to scan Wi-Fi and using neo -7m. scan Wi-Fi locations
Do you think this can be done?
Hello, I've not tested the library with this module. You may use the code shown in this video so you can get location without library ruclips.net/video/rCXYP6H3gSE/видео.html and WiFi scan can be done at the same time. Good luck
Thank you for the video. I can send the gps data signal from arduino to my cell phone but is it possible to use that data to get a live pin to a map, without updating all the time? (Maybe with an app or a website?)
Thank you very much for your time.
You are welcome. Yes it is possible but it needs a service. I have a plan to create such service but it is a lot of work. You find Amazon AWS free service that takes data from GPS from Arduino and your app can connect to the service. Search Amazon AWS.
@@robojax Thank you very much. You have my respect.
You are welcome. It is my pleasure to help. Respect.
Hi. How did you do 13.42? That means Location INVAID => OPERATION WELL?
Hi, you made me watch the video. I said "it means wiring is correct" and of course there is no signal
Hello, Is it possible to get the gps coordinares of a particular location if the value of a sensor exceeds its threshold(which i give in code)?
Thanks in advance!
You are welcome. The best thank you for me is to subscribe to my channel and thumb up the video. It is greatly appreciated. 🔔 😊. You haven't subscribed yet.
will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊
Any tutorial
Any Tutorial for wireless connection with neo 7m module
see the title. it is about 7m.
One time again nice sir
Sir pls make a video of 4 pin gps imean neo 6 4 wire connection for apm 2.6
number of pins do not matter. TX, RX, VCC and GND is needed.
Big time quiestion, that's driving me crazy. Why on Earth does it has an RX pin. Can someone help? Can I send Data to the GPS Module? I am talking Commands to read a specfic NMEA Sentence
Yes you can send and set parameters including power and sleep mode. Read the datasheet and if you figure it, you can control it. This video is about extracting location.
No GPS detected: check wiring
I've gone over the wiring multiple times, checking for connections and everything seems fine, could it be that the GPS is broken?
Hi, I am not sure. Try my code from this video ruclips.net/video/rCXYP6H3gSE/видео.html and if GPS can see sky towards equator, then GPS module is bad.
Is 6m and 7m's codes are same?
I don't remember what I said in the video. if I mentioned to select the model, then do it. if not then it means the same code work. Here is another video on GPS so you can use it without library and I have explained it so you can get location ruclips.net/video/rCXYP6H3gSE/видео.html
is SPI interface enabled in those gps modules?
yes it is. Please see datasheet's page 9 www.u-blox.com/sites/default/files/products/documents/NEO-6_DataSheet_%28GPS.G6-HW-09005%29.pdf
Hi does it need internet to give location?
Yes of course. without antennat it won't work.
hello! how can i connect Gps Neo7M to arduino?
Hi, I believe this video is about 7m as well. Just follow the instructions
Thank you, I upload the code and it work properly
You are welcome.
Thanks for sharing this video. i have tried neo7m0000 beside the window for long time but the data stay same $GPGSA,A,1,,,,,,,,,,,,,99.99,99.99,99.99*30 and never change and the light doesn't blink.
even before i tried neo6m it worked two times outside then stop for ever. i am no sure what is the issue with gps. can you help
Hello, so check the wiring. First test your code without connecting the GPS module. if you are getting the same data, then it means GPS is not receiving or sending data to Arduino. Also have you checked this video which very simple without library: ruclips.net/video/rCXYP6H3gSE/видео.html
I waited 2-3h first time :) to get first signals (next time
I want to make tracker for car. But does this GPS only work outside? How can I get GPS for inside car?
You would have to put under the windshield in plastic box and connect the wires to your board.
@@robojax thanks. how do they make GPS car trackers where they put the tracker in the trunk or under the car. How do they work?
Wherever you put them, they must get signal. Signal can't reach if antenna is covered with metal. so you may put antenna outside like a small wire that can can see sky.
Robojax will tinfoil layers on dashboard block signal?
Hello Sir, I have uploaded the code successfully on the board just as how you instructed in the video. However, it still shows in the serial monitor that the location is invalid though I went near the window and the neo 6m started blinking. What could possibly be the problem?
I am not sure. Perhaps the wiring is bad, voltage is low, signal is not reaching or module is bad.
What i need to do to make this work with an Arduino NANO? cause it only has a 5v supply and not the 3.3v that Arduino UNO has..
Arduino nano has 3.3V see it here www.theengineeringprojects.com/wp-content/uploads/2018/06/introduction-to-arduino-nano-4-1.jpg
Can we do this without serial monitor of aurduino
Serial monitor is to develop and learn. Then you would use it to take some action. Watch the video and I explained why people need this.
Can i get the gps coordinates from the usb connection?
when it prints it on serial monitor, that is USB. just read it. Arduino is reading it from USB and printing it for you, now you do your job to get in your Window/Linux/Mac machine to read it outside Arduino. if that s what you want.
@@robojax what i meant is can i get the gps info from the micro usb port ?
Please read above.
@@robojax Thanks
what about we want to get signal from 2 gps? i mean, i have 2 gps and i want to get signals from them with 1 antenna which connecting to my pc. Is it possible that get signals from 2 gps with 1 antenna at the same time?
I don't think you can use the same antenna for two GPS receiver. The antenna is active device, it has electronics and it communicates with receiver.
@@robojax Thanks for your answer
You are welcome.
please provide the link for the manual/datasheet of neo 7m gps module
In the description of the video, I have link to the page on Robojax.com where you can get the code. The datasheet is provide in the same page where I put the code robojax.com/learn/arduino/?vid=robojax_GPS_TinyGPSPlus
Thank you
how can we use Neo 6 or 7 with nodemcu ESP8266 module
Interesting but usually GPS application are outdoor where you won't have WiFi. What would be the application?
can i know what is difference between neo 6m and neo 7m ?
Neo 7m has more accuracy and faster refresh rate. here is the official page foe Neo-6m www.u-blox.com/en/product/neo-6-series and Neo-7m www.u-blox.com/en/product/neo-7-series
Hi, thanks for sharing your knowledge
I ran the program and the gps displays INVALID, date 00/00/000, time 00:00
gps.location.isValid() return INVALID
Location: INVALID Date/Time: 0/0/2000 00:00:00.00
Location: INVALID Date/Time: 0/0/2000 00:00:00.00
Location: INVALID Date/Time: 0/0/2000 00:00:00.00
Can you tell for what reason?
Tks !!!! Bruno
No signal. Make sure Gia module can see the sky. If you are above equator it should see the sky the south
@@robojax Thanks. Unfortunately, none of the 2 gps are working. I am using the Ublox 6M V2. Many thanks for the reply
Search my channel and see the other video for gos.
The led on my GPS module is not turning on. Help plz
it is not receiving signal. the module should be able to see the sky clearly.
where did you order the gps?
just type "gps arduino" in your search on eBay.com or AliExpress.com or Amazon.com
if , I want the 5HZ update rate of NEO 6M gps instead of 1HZ(default) and baud rate instead of 9600(default).....
thanku
You can't . You would you have buy the faster refresh rate NEO 7M or Neo 8M which are fast and expensive.
+Robojax but in NEO 6M gps datasheet .it has mentioned that ,it's maximum update rate is 5HZ .
you are right. look at this page github.com/jlnaudin/x-drone/wiki/How-to-setup-the-GPS-Ublox-NEO-6M-(Crius)-CN-06-V2
thank you....
you are welcome.
Is this wireless?
GPS is receiving signal from satellite? did you watch the video? You should not have ask this question if you watched the video.
where do i get the datasheet
from the same page where you get the Arduino code. The link is (always) below the video in the description.
@@robojax I saw the datasheet of the ublox core, but I wanted the datasheet of the entire module itself, I can't, right? I've tried to find it on Google but it doesn't have
you won't find it. this module-with-pcb even doesn't have a model number. someone just produced it and assumed you use the main datasheet. Besides it has very few components which you can search online for each and know what they are. Good luck.
Thanks
You are welcome.
Many little errors and shortcut text in this video. You say connect to pin2, but plug a wire into what is labelled D1. You talk about the Serial Monitor connection, when the statements you refer to are for the software serial connection, which is what communicates with the GPS. Then 'connect Tx on the GPS to rx', but omit the additional words 'on the Arduino'. Kind of misleading. Difficult to give it a thumbs up.
Than you for your comment. I appreciate it. I am not sure if you are familiar with Arduino, in this context which we get the data using Arduino board, Serial Monitor is within Arduino an pin2 is also refers to pin 2 of Arduino. I will read the errors in text. The title of the video is the words "in Arduino". I am sorry if you felt mislead. But greatly appreciate your comment.
thnx bro
You are welcome.