Thank You for this Video, I am waiting that my SKR 3EZ arrives in the next days, After a few attempts, i was able to create a firmware file for the board.
I got ine question. As my old creality board stopped working tday(running on klipper) and i was used to set the vref directly in the drivers how is this done here? Directly in klipper via the current in the printer. Cfg file? Kr and thx very much!!
Is it safe to assume that VUSB pins could be used to connect the ATX PSU 5V Vsb in order to provide standby power to the board and later on to control the ATX PSU on and off via PS_ON pins? Thanks in advance!
Dear Ed, I have followed both the Bigtreetech and your setup for my SKR 3 EZ for serial ports with Marlin 2.1.2. After compiling and uploading the firmware via Micro SD card, i get the correctly renamed filename FIRMARE.CUR, so everything kind of looks ok. That is until I want to connect the USB port and/or the TFT35. I've matched the baudrates and still...nothing. I can't connect via Pronterface either. In the info section of the BTT TFT35 it shows System: unknown. I am running out of ideas.... have you got any ideas what could be the cause? the only thing I haven't tried is a 4gb micro sd card. Didn't get a card with my SKR 3 EZ, so I am using a correctly formatted 16gb.
This really is the very worst video ever. If you are 'not sure' about lots of stuff then you should study the material rather than to produce a video with a whole pile of forward references and errors in it.
How's it going I need your help. I'm trying to use raspberry pi on my printer for klipper. When I try to get the serial port I get this info. ls /dev/serial/by-id/', pi says "ls: cannot access '/dev/serial/by-id/’: No such file or directory".
Thank You for this Video, I am waiting that my SKR 3EZ arrives in the next days,
After a few attempts, i was able to create a firmware file for the board.
You're welcome.
Thanks! Ill go for this version!
You're welcome.
I got ine question. As my old creality board stopped working tday(running on klipper) and i was used to set the vref directly in the drivers how is this done here?
Directly in klipper via the current in the printer. Cfg file?
Kr and thx very much!!
There's a playlist for tutorials in description of video.
Is it safe to assume that VUSB pins could be used to connect the ATX PSU 5V Vsb in order to provide standby power to the board and later on to control the ATX PSU on and off via PS_ON pins? Thanks in advance!
Dear Ed, I have followed both the Bigtreetech and your setup for my SKR 3 EZ for serial ports with Marlin 2.1.2. After compiling and uploading the firmware via Micro SD card, i get the correctly renamed filename FIRMARE.CUR, so everything kind of looks ok. That is until I want to connect the USB port and/or the TFT35. I've matched the baudrates and still...nothing. I can't connect via Pronterface either. In the info section of the BTT TFT35 it shows System: unknown. I am running out of ideas.... have you got any ideas what could be the cause? the only thing I haven't tried is a 4gb micro sd card. Didn't get a card with my SKR 3 EZ, so I am using a correctly formatted 16gb.
In description of video there's a Discord link either myself or someone else can help you in general chat.
Thanks! 😊 I'll try that
Tres
This really is the very worst video ever. If you are 'not sure' about lots of stuff then you should study the material rather than to produce a video with a whole pile of forward references and errors in it.
How's it going I need your help. I'm trying to use raspberry pi on my printer for klipper. When I try to get the serial port I get this info. ls /dev/serial/by-id/', pi says "ls: cannot access '/dev/serial/by-id/’: No such file or directory".
Means firmware is probably not flashed to printer board.