i am making a project and having problem, i have a pam 8610 connected to 20watt 4ohm + 10watt 4ohm speakers in series on both channels so 8ohm per channel and power supply as 3x 18650 batteries, input from 5v Bluetooth module which gets power from a 7805 regulator , i have also added capacitors between battery and amplifier of 4700uf+1000uf and a 22k resistor on sound output from Bluetooth module to reduce distortion but it still has a lot of distortion and clipping and most song are not even listenable and a voltage drop of 0.2-0.4v while running plus the chip runs hot even having heatsink on top, pls help i am stuck
do not try to be more jugadu in order to fullfill your requirements, so please do not add speakers in series or parallel in order to maintain ohm and wattage. connect 4ohm speakers on each channel. and if you are using 18650 in series then use perfect bms and never use 7805 voltage regulators for highly sensitive project like audio amplification cause 7805 is like jugadu or sasta way to regulate voltage and it makes lot of frequencies which can get easily catch by amplifier. in order to prevent it, you can use aditional 4v battery to power up bluetooth module.your problem will be solved.
the distortion is coming in the form of frequencies not in form of voltage so you can not avoid by resistance or capacitors, you have to common the grounds, so that aditional frequencies coming from 7805 can be ground. by the way you never should use 7805 in amplifiers because 7805 makes very bad frequency which can get caught by amplifiers easily and amplifier would distort your sound badly.
Hi there! Thanks for the video. I would like to ask you a question. I have the same circuit. As soon as I increase the volume above half on my device, the amp's sound becomes louder for a split second and cuts off, this loops until I put it back onto half volume. Do you know why? Thanks.
Pam8610 ko kitne apmear ke transfer se supply de sakte hai Maine 12-0-12 ke 1 apmear se supply diya hai to valume badane par board off ho jata fir on hota fir off hota ........
this amplifier board not design to make studio quality sound.. I think you should use other amplifier boards they will give you much accurate sound like studio.. this amplifier board is designed to give low mid and bass output only..
Bhai mere pas 3Ω 20w+20w Bass Speaker hain aur 3Ω 20w+20w Treble Small Speaker hain... Kaise connect karun, iski aap Video bana kar lagao aur bataye ke main apna Speaker kaise bana sakta hun... Kaun kaun se Circuit Board lene parenge mujhe...
let me think ye bhi kya possible hai? maximum ham 20 watt nikal sakte hain.. is ic ke data sheet anusar per channel 10 wat hai.. agar ine donon Ko kisi bhi tarike se bridge banaa bhi De to sirf 20 watt niklega..
mehnat dikhti hai salam apko
Tom bohoy funny ho vai😂 but video jabardast k
Hota hein..😊
Bro You can Make Vlog Videos That will be a game changer for you..
i tryed but didn't worked...😵💫
@@Epnguy keep trying
Hi bro first comment and love u bro
thank you
Nice video bro 🤩🤩
nice bro..... tested very well...
i am making a project and having problem, i have a pam 8610 connected to 20watt 4ohm + 10watt 4ohm speakers in series on both channels so 8ohm per channel and power supply as 3x 18650 batteries, input from 5v Bluetooth module which gets power from a 7805 regulator , i have also added capacitors between battery and amplifier of 4700uf+1000uf and a 22k resistor on sound output from Bluetooth module to reduce distortion but it still has a lot of distortion and clipping and most song are not even listenable and a voltage drop of 0.2-0.4v while running plus the chip runs hot even having heatsink on top, pls help i am stuck
do not try to be more jugadu in order to fullfill your requirements, so please do not add speakers in series or parallel in order to maintain ohm and wattage. connect 4ohm speakers on each channel. and if you are using 18650 in series then use perfect bms and never use 7805 voltage regulators for highly sensitive project like audio amplification cause 7805 is like jugadu or sasta way to regulate voltage and it makes lot of frequencies which can get easily catch by amplifier. in order to prevent it, you can use aditional 4v battery to power up bluetooth module.your problem will be solved.
the distortion is coming in the form of frequencies not in form of voltage so you can not avoid by resistance or capacitors, you have to common the grounds, so that aditional frequencies coming from 7805 can be ground. by the way you never should use 7805 in amplifiers because 7805 makes very bad frequency which can get caught by amplifiers easily and amplifier would distort your sound badly.
Hi there! Thanks for the video. I would like to ask you a question. I have the same circuit. As soon as I increase the volume above half on my device, the amp's sound becomes louder for a split second and cuts off, this loops until I put it back onto half volume. Do you know why? Thanks.
Then you should use a more powerful power supply like 12volt , 2ampere
Bhai kya hum Bluetooth module Mai dono output se ekbar mai output le sakte hai kya
Le sakte hain lekin 1k register lagana padega
@@Epnguy Bluetooth module pe ya amplifier kidhar lagana padega 1k resistor
Can you just tell me, when I use 12 V power supply on PAM 8610 it gets heated with a 15 Watt speaker 8 ohm?
aapne kitne ampere ka charger use kiya isme?
Pam8610 ko kitne apmear ke transfer se supply de sakte hai
Maine 12-0-12 ke 1 apmear se supply diya hai to valume badane par board off ho jata fir on hota fir off hota ........
Bro 8 ohm per channel ka load le sakta hai kiya
Lega
Can we make 8 inches woofer and 1inches tweeter someting like stidio monitor with this....
this amplifier board not design to make studio quality sound.. I think you should use other amplifier boards they will give you much accurate sound like studio.. this amplifier board is designed to give low mid and bass output only..
@@Epnguy can i use tpa3116d2???...or sugggest me some???....and do i need crossover...
Kya ise tv k andar bhi fit kar skte hain
Yes
Bhai mere pas 3Ω 20w+20w Bass Speaker hain aur 3Ω 20w+20w Treble Small Speaker hain... Kaise connect karun, iski aap Video bana kar lagao aur bataye ke main apna Speaker kaise bana sakta hun... Kaun kaun se Circuit Board lene parenge mujhe...
Gold 601e ki bhi video lao
Usme ek problem aa gayi hai to koi solution btaiye pls
problem kya hai?
ruclips.net/user/shortsY_qYLeOjUrQ?feature=share
Ye video dekhiye aisi problem hai
What is price wherein is avaliable?
Es board se 30 w kaise nikale? Bridge krke
let me think ye bhi kya possible hai? maximum ham 20 watt nikal sakte hain.. is ic ke data sheet anusar per channel 10 wat hai.. agar ine donon Ko kisi bhi tarike se bridge banaa bhi De to sirf 20 watt niklega..
Bhai 5-6 apmree use krne se bass nhi phatega sayad
Mera tpa3118 amplifier hai original with 32pins
Kahan se liya
Mere pass 2 pam 8610 board hai, aap se bhi ghatiya wire se wiring kiya hoon koi humming nhu nhi aata.
Bord ka life kay hay
Ic burn ho jayega
6 inch woofer chalega
Hello Bhai
❤❤❤❤😂😂🎉🎉🎉
12v 3amp...adapter ya transformer use kare awas nahi phatega !!!
pura damdar bass ayega
Aapke pass duplicate pam8610 h
😂😂😂😂😂😂😂
Bhai ye 15w +15w ka hai
nehi 10+10
This is fake pam8610
It is fake
why you say it is fake? how to find fake or original?
😊
Bhaai tum bhot casually baat jarte ho achhaa hai 😅