We've all been there with the smaller compressors to start out with. I too changed all my couplers and plugs to the Milton-V, high-flow fittings, just has you have there. Unfortunately, I found that those pretty anodized aluminum couplings get torn up from pneumatic impact use. I've since had to go through and replace all the plugs with one's made of "steel" from Milton, which are also Milton-V, high flow fittings. Hope your compressor project is coming along well.
Did you check the air flow rating on your swivel? If it doesn’t flow like the new fittings and couplers, you likely haven’t improved anything at all. The flow rate is always only as high as your most restricted component will allow.
One thing that will help you alot will be changing all of the connectors out with high flow. I see your hose going into your tank doesn’t have a high flow male end. Also possibly adding a auxiliary tank. That will greatly increase your scfm for pretty cheap. Great videos!!!
Suggestion, take the water filter and relocate as far away from compressor as possible. These only will capture some liquids that condense out due to cooling. Air leaving the top of a compressor is hot and the water is in a vapor state which almost everything will pass directly thru the filter. Replacing couplers to high flow is good, replacing couplers with new will most likely eliminate leaks from old couplers. About 30% of all the compressed air produced in the world is from leaks.
Hi Neighbor! Those look pretty cool. I have a Craftsman 25 gal compressor. I just use it for a brad nailer, inflating tires, and blowing dust out. All the air leaks out pretty quickly, so this makes me want to take the attachments off and reseal them with teflon tape. Hope all is well in the foothills.
Glad you checked in. We need to have lunch sometime when things settle down. If teflon tape doesnt stop the leak, Check the inside of the coupler. That was my problem. Let me know if you have issues. I also had a check valve leak,but that is a whole other story.
the hi flo fittings increase your performance a lot your swivel because it is a ninety reduces performance a lot air flow is only as good as the weakest part of your system
Your entire setup must be high flow in order to increase your air output. Starting from the compressor to the tool, every connection has to have a high flow attachment or you’re negating the purpose of the upgrade.
![NLE Choppa - Or What ft. 41 (Orchestra Mix) [Official Music Video]](http://i.ytimg.com/vi/biOFASEgSOM/mqdefault.jpg)
We've all been there with the smaller compressors to start out with. I too changed all my couplers and plugs to the Milton-V, high-flow fittings, just has you have there. Unfortunately, I found that those pretty anodized aluminum couplings get torn up from pneumatic impact use. I've since had to go through and replace all the plugs with one's made of "steel" from Milton, which are also Milton-V, high flow fittings.
Hope your compressor project is coming along well.
Did you check the air flow rating on your swivel? If it doesn’t flow like the new fittings and couplers, you likely haven’t improved anything at all. The flow rate is always only as high as your most restricted component will allow.
I have not. I need to. I love the swivel so much. I need to find a high flow version if this one is restricting. Thanks for watching.
One thing that will help you alot will be changing all of the connectors out with high flow. I see your hose going into your tank doesn’t have a high flow male end. Also possibly adding a auxiliary tank. That will greatly increase your scfm for pretty cheap.
Great videos!!!
Great catch. This was just the beginning. I will keep your idea in mind. Thanks for watching.
Suggestion, take the water filter and relocate as far away from compressor as possible. These only will capture some liquids that condense out due to cooling. Air leaving the top of a compressor is hot and the water is in a vapor state which almost everything will pass directly thru the filter.
Replacing couplers to high flow is good, replacing couplers with new will most likely eliminate leaks from old couplers. About 30% of all the compressed air produced in the world is from leaks.
great tips. thanks for watching.
Hi Neighbor! Those look pretty cool. I have a Craftsman 25 gal compressor. I just use it for a brad nailer, inflating tires, and blowing dust out. All the air leaks out pretty quickly, so this makes me want to take the attachments off and reseal them with teflon tape. Hope all is well in the foothills.
Glad you checked in. We need to have lunch sometime when things settle down. If teflon tape doesnt stop the leak, Check the inside of the coupler. That was my problem. Let me know if you have issues. I also had a check valve leak,but that is a whole other story.
I use them for my 12v 5 gallon home built compressor.
nice. thanks for watching.
Good idea
Thank for watching!
the hi flo fittings increase your performance a lot your swivel because it is a ninety reduces performance a lot air flow is only as good as the weakest part of your system
True. But I love the swivel action. Maybe I need to look for a high flow swivel. THanks for watching.
Bigger hole will = to your compressor coming on more frequently cause your using more air.
Why do most people who do how to videos put the teflon tape on wrong?
Because there is a camera on them.
@@TheGarageEngineer I got to thinking too, sometimes the camera films things as if you were looking in a mirror. Enjoy the videos.
Your entire setup must be high flow in order to increase your air output. Starting from the compressor to the tool, every connection has to have a high flow attachment or you’re negating the purpose of the upgrade.