How to Replace Serpentine Belt & Tensioner 2007-2011 Honda Civic
HTML-код
- Опубликовано: 8 сен 2024
- Buy Now!
New Serpentine Drive Belt Component Kit from 1AAuto.com 1aau.to/ia/GAEE...
This video shows you how to install a new tensioner pulley and serpentine belt on your 2007-2011 Honda Civic. That squealing noise coming from your vehicle’s engine compartment could be a slipping belt, or it could be a bad pulley bearing, or both. A bad pulley could eventually damage the belt, which could create even further damage. Replace both at the same time with this convenient kit!
This repair was done on a 2007 Honda Civic EX 1.8L and the process should be similar on the following vehicles:
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
Tools you will need:
• Phillips Bit in a Ratchet
• 10mm Socket 1aau.to/oJq/1AX...
• 12mm Socket 1aau.to/oP4/1AX...
• 19mm Socket 1aau.to/otw/1AX...
• Trim Tool Set 1aau.to/op2/1AX...
• 15/16 Inch Socket
• 1/2 Inch Breaker Bar 1aau.to/oeH/1AX...
• Torque Wrench 1aau.to/oz3/1AX...
• Safety Glasses
• 8mm Allen Wrench
• Drain Pan
Subscribe: / @trq
Check out our playlist:
Honda Civic 2006-2011 8th Generation: • Honda Civic 2006-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
tutorials from this content provider are often missing very valuable information. They seem to want you to buy parts from them, but their tutorials really do need some work. let Sue do the demonstrations for things like this, she definitely does a much better job than any of the other providers working for this company.
Did I miss it, or did it not show the belt routing around all of the pulleys?
In order for you to access the 8 MM hex (as you did) from under the fender, you first have to removed the motor mount and lower the engine - I'm puzzled why this video didn't mention that? Kind of misleading if you ask me.
Those who get the 8 mm hex off at first try can give themselves a party. BTW, whats the 'limited' warranty on the parts?
is there a way to take the bolt off from the top? The 8 hex bolt
By any chance, do you have the part number for the belt that you used? Thank you. Your answer would be greatly appreciate it. I’m working on the same thing and the belt from AutoZone is too long not save the old belt.
Did you swap out the water pump too?
I check and it’s another $150 and I would do it
How push so hard belt!!
What would the cost for this repair?
Could you do a timing chain video
Please
+Charles Payne We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-TRQ
@@TRQOK thanks
The 8mm bolt on the bottom of the tensioner is stripped. Any ideas on how to remove?
Hammer in a Torx
Or: Drill out the head and remove the tensioner
Or: Leftrotation drill
Or: Bolt remover (left turning)
You can go to Harbor freight tools and get a bolt extractor kit.
My belt tool touches the motor mount
Man I wanted to bypass the ac compressor the tensioner stripped before it started to move.😢