Who would have thought that someone could make replacing a bearing on a washer both interesting and entertaining! Lots of great tips. Thanks and, keep the great videos coming!
FYI, my Horizons are about 7 years old, and the internal threads on the end of the main basket shaft are LEFT handed threads!!!! Be aware of this when you are removing the bolt!!!! I apologize for repeating it, if you said that in video, but I didn't pick up on that, but it is definitely worth repeating!!! I learned the hard way!
Biggest trick to it. Dont let the bearing wear too much. Once you hear the noise start take machine out of service. Seem like if it goes for a few days that shaft wont let go of the bearing. Good Luck!
I use my socket set for the car to knock the bearing out. Saves scratches on the housing. Another handy thing to have is a magnetic plate to hold all the little screws cos 9 times out of 10 you come to put that last screw in and you can never find it. I hate replacing bearings. On domestic machines I usually tell people to just scrap them cos it's not worth the hassle plus new machines are so cheap and it's not cost effective to do a bearing replacement
As a prior auto mechanic there are bearing and seal driver kits made specifically to replace them where the flat plate matches up and drives it in straight. No tapping around the edge to walk it in, less potential hub damage There are several kits starting around $30 with 8-10 sizes in the kit. If a larger size is needed look at heavy truck parts store for sizes up to around 8"diamater
Great video -- I've actually got one of these to change, but, the plan was always to find the generic bearing numbers to rebuild the 'spare' so that we can keep swapping hubs out to save time in the middle of the night (most repairs are done late night). A nice thing to have sometimes for this sort of thing is a pneumatic air hammer/chisel -- noisy as all get out, but very effective. I'm now wondering if there's an SDS bit that would work as a regular hammer, as I've already got a cordless SDS+ hammerdrill that technically should work for this purpose....
we have a 20 lb huebesh washer. the issue we have is it leaking on the 6 o'clock position and the rubber seal is okay on this machine. do you have videos that shows how to troubleshoot this
My washer is bouncing around like crazy, it's level and on a concrete floor with rubber feet. I replaced the shocks using your video but it's still really bouncy and out of balance. Do i need to replace the bearing or is it something else?
Bad bearing will give a roaring sounds. At 1st very low roar. Then a couple days it will be very loud. Bangy and unbalanced sounds more like you bolts. Either your base is loose or the machine bolted to base is loose. If it also shake that would be issue. When machine off you can rotate the drum and hear the bearing. If not bearing ok. Hope that helps!
If heating it won't free it. What alot of repairs guys do is cut the drum shaft. They reach behind hub with a Sawzall and cut the shaft. You'll be able to reuse the hub. But you will need a new tub. What's happen is the bearing has seized on the shaft. Another option is to chip out outer bearing you see then use long punches to knock out inter bearing. If you have two bearings in hub.
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Great video. Do you have part 2?
Go to Hot Dogging with Dan channel!!!
Who would have thought that someone could make replacing a bearing on a washer both interesting and entertaining! Lots of great tips. Thanks and, keep the great videos coming!
FYI, my Horizons are about 7 years old, and the internal threads on the end of the main basket shaft are LEFT handed threads!!!! Be aware of this when you are removing the bolt!!!! I apologize for repeating it, if you said that in video, but I didn't pick up on that, but it is definitely worth repeating!!! I learned the hard way!
You are doing the Lord's work with this comment. I spent 2 hours cranking the wrong way. Thank you so much.
THE MAIN REAR SCREW IS REVERSE THREADED!!
@@jg3543 😂😂 Glad I could help!!
I caught this when I began to see the washer bending! 😮
Thanks Keenan! Tackling this job today in my mat.
Biggest trick to it. Dont let the bearing wear too much. Once you hear the noise start take machine out of service. Seem like if it goes for a few days that shaft wont let go of the bearing. Good Luck!
Brother, I love your work ethic. Keep up the great work. Your content is second to none.
thanks for this video saved me lots of time!!
Another excellent video and really detailed. Keep them coming!!!
Thanks Keenan, going to attempt changing my bearing tomorrow. looking forward to part #2 of your video.
I love these repair videos. Keep em coming!
Thanks. I am retired and this kind of stuff looks like fun!
I use my socket set for the car to knock the bearing out. Saves scratches on the housing. Another handy thing to have is a magnetic plate to hold all the little screws cos 9 times out of 10 you come to put that last screw in and you can never find it. I hate replacing bearings. On domestic machines I usually tell people to just scrap them cos it's not worth the hassle plus new machines are so cheap and it's not cost effective to do a bearing replacement
Thanks for the advice, Keenan!
great video
As a prior auto mechanic there are bearing and seal driver kits made specifically to replace them where the flat plate matches up and drives it in straight. No tapping around the edge to walk it in, less potential hub damage There are several kits starting around $30 with 8-10 sizes in the kit. If a larger size is needed look at heavy truck parts store for sizes up to around 8"diamater
I’m just a shade tree guy but those kits are worth it to me too.
How far you chase that man for those pants !
15:50 - whats the song? From the youtube free music selections?
Great video -- I've actually got one of these to change, but, the plan was always to find the generic bearing numbers to rebuild the 'spare' so that we can keep swapping hubs out to save time in the middle of the night (most repairs are done late night). A nice thing to have sometimes for this sort of thing is a pneumatic air hammer/chisel -- noisy as all get out, but very effective. I'm now wondering if there's an SDS bit that would work as a regular hammer, as I've already got a cordless SDS+ hammerdrill that technically should work for this purpose....
we have a 20 lb huebesh washer. the issue we have is it leaking on the 6 o'clock position and the rubber seal is okay on this machine. do you have videos that shows how to troubleshoot this
Good job! Is it possible to change the spinspeed of this model? I have this an it spins only about 600-800 rmp.
My washer is bouncing around like crazy, it's level and on a concrete floor with rubber feet. I replaced the shocks using your video but it's still really bouncy and out of balance. Do i need to replace the bearing or is it something else?
Hey Keenan - great Video - I had a look at Hot Doggin with Dan channel but can't find part 2...is it still up?
Thanks
Never mind I just found it...title is..Going On Vacation with a Laundromat!$! | Following Keenan ! Bearing Replace Part #2
The bearing kit calls for using Loctite 680 (green) on the bearing seats. Do you do this?
I did not.
Carefully also the bolt holding that pulley on is reverse thread.
Please do a video on the speed Queen 30lb or 40lb bearing change
I can do that!! It will be a few weeks. Those bearing are easier than horizon, surprisingly.
Do you know what bearings to buy if I have an extra bearing housing?
What are the symptoms of a bad bearing? Does it make a grinding noise? Mine keeps giving C1 errors and it sounds bangy and unbalanced. Thanks
Bad bearing will give a roaring sounds. At 1st very low roar. Then a couple days it will be very loud.
Bangy and unbalanced sounds more like you bolts. Either your base is loose or the machine bolted to base is loose. If it also shake that would be issue.
When machine off you can rotate the drum and hear the bearing. If not bearing ok.
Hope that helps!
@@FollowingKeenan Thank you!
Great video is any way i can send you a video of my washer it it shakes a lot it look like the door is going to open
Can email it FollowingKeenan@gmail.com
If its a hard mount, sounds like floor bolt or two is loose. Doesnt take much for machine to shake.
I send a video via email can you pleace let me know what you tink it can be
I just sent a response you email was in the spam folder. Love technology!
@@FollowingKeenan I will thanks a lot
Where can I find the belt change video?
I want to send you a video of this washer creating noise, how can I ?
Where can we buy the bearing press?
Horror Freight!
Ah what puller I'm stuck
Hello, I need help(guidance) in the speed queen stacker washer. Please help I am stuck.
I am from India.
And don't cut yourself .I fixs home appliance .a laundry mat owner wants me to work on his appilenss . trying to learn how to 👍🇨🇦
Bearing hub os not coming out its stuck, please guide me.
If heating it won't free it. What alot of repairs guys do is cut the drum shaft. They reach behind hub with a Sawzall and cut the shaft. You'll be able to reuse the hub. But you will need a new tub. What's happen is the bearing has seized on the shaft.
Another option is to chip out outer bearing you see then use long punches to knock out inter bearing. If you have two bearings in hub.
Is there any locking system, like a small Ln key screw from below of hub centre hole between two bearings ?
Somebody suggested me ...
Wooden base in a laundry ?????? Great video but that thing seems so flimsy that it could destroy itself in a out of balance load on spin.
Anyone find part 2?
Could i get the parts number for the bearings? I cant find the large one on grainger
Only 561 views and 80 likes? Ouch.