That's bullshit. Vertical down is nothing more than cosmetic, no strength in it at all. Do not do it. Only pipelines should weld vertical down - and that's an entirely different procedure.
i am a arc welder..this is my firs time to see vertical down ward welding,i try like this technique,i think it so difficult but i try. you use E 6013 ORDINARY welding rod but you done in good way..thank you for sharing ..
Все правильно !!! Сверху вниз без манипуляций !!! потечет металл с о шва если водить элэктрод со стороны в сторону . И конечно ток по толщине металла . тип элэктрода ну и его влажность + напряжение в сети ...
Yukardan aşağıya rutil-selülozik yani rc elektrotla yapılabilir.düz bir şekilde salinimsiz kaynak yapılır.rr rutille olmaz.dediginiz gibi dikkaynak yapilir
Essa segunda solda descendo e permitida numa chapa dessa espessura e com eletrodo e 6013 por eu acho que tem que ser solda acendente e com eletrodo 7018 de 2,25
Verdade. Tem muito "professor" de solda que não sabe fazer uma solda bem feita assim. Mas tenho minhas dúvidas se essa última foi feita mesmo na vertical porque se vc prestar bem atenção a poça de fusão atrás da solda não escorre. Se foi mesmo soldada na vertical, parabéns.
La soldadura descendente aprendí que se usa en metales delgados y para la homologación solo en el primer pase con el chaflán hecho en el material se utiliza la soldadura descendente.
The down hand fillet weld(1st one) didn't have enough amps, the weld bead is distinctly convex, and there's undercut along the upper toe; the second weld, 'vertical down' or 'stoving' as it's known is bad wherever it's encountered, don't do it, Pipeline welders do it on 'low pressure' pipework, and where it's buried in the ground: high pressure situations, structural work is up! Up! Up!
thank you for your video Iam begginer and hope learn arcwelding when welding all welder weaves but when you weld down in this video why dont you weave what's the difference with weaving or not
@@MambinSin no, you don't touch the the plate unless you're using 7024 rod. you can just jam push that rod in and drag it, but for 7018 rod you can't do that.
Muy oscuro el cordón y tiene salpicaduras la pieza. Tampoco he visto que se limpien las piezas a soldar, ni que se calienten los electrodos a utilizar....
Perfect rod angle?? Uhhh, a 45° angle to a 90? Wow!!! Try flat turn diagonal then uphill wrap at 90, overhead turn down hill and meet your first 1F start. No X-ray. But visual. Although it get pressed to see how much pressure it takes to break certain sections. This test isn't traditional and they select coupons to test based on visual. But you aren't told that ahead of time.
@@diegomengoni3494 The first weld was a 7018, second one was 6013. On the second weld, a 7018 run UPHILL would be much more appropriate for that thick of plate! Nice looking downhill bead though!
That's bullshit. Vertical down is nothing more than cosmetic, no strength in it at all. Do not do it. Only pipelines should weld vertical down - and that's an entirely different procedure.
i am a arc welder..this is my firs time to see vertical down ward welding,i try like this technique,i think it so difficult but i try. you use E 6013 ORDINARY welding rod but you done in good way..thank you for sharing ..
Voltage machine kie kitne hone chye
수직용접시에는 아래에서 위로 올리는 걸로 배웠는데요 위에서 아래로 내리면 용접물이 흘러내려 빨리 내려가야 하기 때문에 두 모재가 완전히 녹아 붙었다고 볼수 없읍니다
It depends on rods
You can weld uphill downhill if your rod supports it like 7018
Do you have 7018 rods in Korea ?
Попробуй тонкий метал вертикально ,ещё российским элэктродом )))
нормально вариться российскими электродами
да не важно какой металл. вертикал варится снизу вверх. а этого сварщика в первом же учпункте пошлют на хер.
Все правильно !!! Сверху вниз без манипуляций !!! потечет металл с о шва если водить элэктрод со стороны в сторону . И конечно ток по толщине металла . тип элэктрода ну и его влажность + напряжение в сети ...
вертикал варится строго снизу вверх!!! тут важна не красота, а катет. у него металл десятка, и ее нужно проваривать с катетом, чтобы *полка * была.
Parabéns professor um belíssimo filme de responsabilidades em segurança para nossos olhos!?
Che bella saldatura, complimenti. Fossi capace io a farla così.
Nasty Dimes....GREAT JOB..👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿
لحام التنازلي ضعيف وغير مقبول للسماكات الكبيرة نسبة غرز مافيو ابدا
Kaynak pozisyonu ve parca dik pozisyonda olduğundan yukardan aşağıya kaynak olmaz sadece sıvama olur aşağıdan yukarı dik kaynak yapılır
Yukardan aşağıya rutil-selülozik yani rc elektrotla yapılabilir.düz bir şekilde salinimsiz kaynak yapılır.rr rutille olmaz.dediginiz gibi dikkaynak yapilir
Essa segunda solda descendo e permitida numa chapa dessa espessura e com eletrodo e 6013 por eu acho que tem que ser solda acendente e com eletrodo 7018 de 2,25
No metalon é mais difícil. Desse jeito até eu passo na prova. Mas todas dicas são importantes. Valeu
Nao e bem assin nao amigo!!
Arc Length, Perfect 🔥🔥🔥
Siempre para arriba en posición 3g
Nossa é a primeira vez que vejo uma solda tão bem feita nessa posição com eletrodo
2 posição
Verdade. Tem muito "professor" de solda que não sabe fazer uma solda bem feita assim. Mas tenho minhas dúvidas se essa última foi feita mesmo na vertical porque se vc prestar bem atenção a poça de fusão atrás da solda não escorre. Se foi mesmo soldada na vertical, parabéns.
@@JoseEmidiojsemidio bem obiservado
Também achei pois no 6013 nessa posição muito difícil nao escorrer a solda muito bem feito!!!
Nice 👍👍👍
Hmmm ... downhill 6013 looks like slag of fusion ! 😆
Chỉ sắt tôn dày thì hàn kiểu gì cũng được. Bạn thử hàn với sắt tôn mỏng o.8.và 1 ly xem sao.
My hat is off to you for your welds. Just like a painted picture. How well is the penetration of the weld ???
0% penatration on the vertical down
@@jimmartin9704 How do they test penetration on vertical welds Jim ??? Peace. V
Dificilmente vc vai fazer teste de solda em metalon . Só se for em serralheria e olhe lá. No resto é fogo alto .
At what amperage do you run the vertical?
Good 👍👍👍👍🇪🇬🇪🇬🇪🇬
La vertical en 6013 la soldó de forma ascendente y me queda bien
Excellent video...Thanks for sharing
Wow👏 greetings from Finland
👍👍👌👌
Some say there is no strength in your welding , would you prove them the contrary.And why they say that ?
Aprendi 100% a soldar foi nesse canal
Fico feliz em ouvir isso
@@iron9844 assistindo aqui do Brasil
6013 downhill makes a good looking weld, but I wouldn't use it for thick objects like this...
Nice
Exllent job 👌👌👌👌
Bro porque no soldas de abajo asía arriba
Good but main problem is thin metal 20 gauge pipe welding sheet will be melted and damage
Good job bro
La soldadura descendente aprendí que se usa en metales delgados y para la homologación solo en el primer pase con el chaflán hecho en el material se utiliza la soldadura descendente.
Perdon mi ignorancia, que es el chaflan?
@@rn1238??????? 🤣🤣🤣🤣🤣
@@rn1238 bisel
good job.
Lovely layering..
nice
Thank yuo
6013 1 means all positions vertical up
The down hand fillet weld(1st one) didn't have enough amps, the weld bead is distinctly convex, and there's undercut along the upper toe; the second weld, 'vertical down' or 'stoving' as it's known is bad wherever it's encountered, don't do it,
Pipeline welders do it on 'low pressure' pipework, and where it's buried in the ground: high pressure situations, structural work is up! Up! Up!
Plzz tell me what is the catagory of welding channels
Grasias carnal
Металл 10мм где с таким сталкивается любитель?
Hi engineer Is it possible to show us a video on how to weld the bottom part of a structure
👍👍👍👍👍
احسنت ستاذ
Dik aşagıya hangi elektrodu kullanıyorsun ustam
сверху вниз варит да, красиво но тонко, и хуже вплавляется в центр, на не ответственных конструкциях пойдёт но лучше пройтись также и второй раз
Cantik cantik very beautyful
👏👏👏👏👏 excelente!!! Cual seria la potencia??
Anda a saber, si ni lo mostró
thank you for your video Iam begginer and hope learn arcwelding
when welding all welder weaves but
when you weld down in this video why dont you weave what's the difference with weaving or not
if you need bigger fillet , you weave to save time,, and make the fillet broader
Cakep bnget las turun nya kawan
Nice guru khadi welding hmse gir jati he kese krni pdti he jrur btaye
Yo I just started welding and I am good at welding at anangle with the 12 rod but bad with 10 rod what am I doing wrong
espessura do material ?eletrodo diâmetro do eletrodo?
Nice work sir!
Do you tip the rod head sitting on the plate while u welding? Or there is a little gap in the arc length?
I have the same question about touching plate while welding
@@MambinSin no, you don't touch the the plate unless you're using 7024 rod. you can just jam push that rod in and drag it, but for 7018 rod you can't do that.
you can increase arc force and touch the plate swiftly , the main point is the arc need to be damn tight for vertical
grazie .super 👍👍
Boa noite Amigo! Qual é a amperagem?
How many amps is the current. Thank!.
Hi. Please make one video how to fix electric wire and then start welding.
Hi
วิธีตกแต่งบ้านให้สวย
Muy oscuro el cordón y tiene salpicaduras la pieza.
Tampoco he visto que se limpien las piezas a soldar, ni que se calienten los electrodos a utilizar....
Itu mah api pas besi tebel, cb yg tipis dan bukan sudut tp agak renggang msh gitu kah sudah pasti engga
Muy bueno ese cordon
Pls tell me power and amps adjusting for good welding
Pero cuanto amperage debo poner la máquina de soldar
What is the weldig current
can you show it on thin square pipe
You are amazed thank you very much!
Muito bom
Compañero ninguna soldadura en descendiente está homóloga por lo tanto esa soldadura no tiene la resistencia que de llevar
Perdon mi ignorancia, sabes porque no esta permitida?
Good morning welding
La primera está cruda le falta un poco más de amperaje
Great video. I like it! 200% :-)
Bonsoir du 2.5 6013 combien l ampères montante et descente merci sinon très belle prestation
👍👍
Please mention power output
Amazing.. 🙏🙏👌
👍
Harika ellerine sağlık
Perfect rod angle?? Uhhh, a 45° angle to a 90? Wow!!! Try flat turn diagonal then uphill wrap at 90, overhead turn down hill and meet your first 1F start. No X-ray. But visual. Although it get pressed to see how much pressure it takes to break certain sections. This test isn't traditional and they select coupons to test based on visual. But you aren't told that ahead of time.
cool
Vertikal pozicion ,,⬆️
ممكن اسم ماكنة للحام وعندي مشكلة من الحم يقطع
เหล็กหนาแบบนี้เชื่อมง่าย
Current kitna rakha thha ye likhe nahin sir
Thanks 😊
Good video thanks sir for that
Sir aap mujha welding sekha skta h
На толшину метала посмотрите 😂😂😂😂 я на 2,5 так же варю
رجاءً اكتب رقم المكينه حرارتها
Хороший элэктрод, не то что наша гавно
Thank you
Süpersin 😳🇹🇷
Amos?
Ммм вертикал сверху низ
itu di amper berapa bapak
Uphill
مشاء الله ربي يحفظك ربي عونك
how many amper are you using?
Que tipo de electrodo es ?
@@diegomengoni3494 6013 electrode
@@diegomengoni3494 The first weld was a 7018, second one was 6013. On the second weld, a 7018 run UPHILL would be much more appropriate for that thick of plate! Nice looking downhill bead though!
The stick is good,we can't welding from up to down