All Indego family has the same problem. Do not use the inner tube on the docking station to pass through the green wire... But simply place the wire under the docking station.
Once used once on your lawn, can you see the progress via the app like a robot vacuum? Since it can cut in straight lines and all means there should be a map on your lawn in the app and you can see where it is and maybe even send it to zone 1, 2 etc?
Ein Problem das Bosh seit JAHRENDEN hat :-((( voll nervig, leg das kabel aus dem kanal raus, und setz es genau mittig in die Station und dann gehts perfekt
Der Draht führt leicht schräg in die Station und deswegen fährt er leicht schräg ein und trifft somit nicht die Ladepunkte. Zudem muss der Draht oben auch gerade verlegt werden, also von der Station gerade aus nach rechts, also es sollte ein 90 grad Winkel sein.
It is all correctly installed at 90 degrees. The solution for me was as suggesed by ROMKYY - changing the docking station position from "normal" to "corner" in the advanced menu.
Thanks for the suggestion. I am pretty sure it is all correctly installed. I used a spirit level to ensure it was perfectly flat and the wire runs in to the base station at 90 degrees.
@@markush.5669 Yep, all correct. The solution for me was as suggesed by ROMKYY - changing docking station position from "normal" to "corner" in the advanced menu.
Der Bosch Indigo S +500 leuft leider nicht 100%! Ja das mit dem Kabel habe ich jetzt auch versetzt aber bin der meiner das die Softwear sehr viele Probleme macht. Ich hatte den gardena sileno City 250qm getestet und muss sagen, dass das mit dem leitkabel wo der Robert den weg zur Station sucht Sinn macht!
Hi Jan, it seems to have worked out itself to reverse a little further and try again without leaving the garage. It normally docks successfully 2nd time around now. I tidied up the wires behind the dock which may have been interfering with the signal. Very happy with it otherwise. Very good navigation and cutting lines and restarting cut where last cut ended.
Bosch hat ein Problem mit der Digitalisierung. Alle ihre Geräte sind veraltet, weil es an IT Fachleuten mangelt. Ihre Apps sind immer zehn Jahre zurück geblieben als Dieter Chinesen.
All Indego family has the same problem. Do not use the inner tube on the docking station to pass through the green wire... But simply place the wire under the docking station.
majster wazzup sobie poradził pierwszorzędnie ;) fachowa robota
no jo
wazzup nie ma stacji w narożniku więc ten problem jego nie dotyczy
Probiere mal die Leitung um bis 3 cm nach rechts zu verschieben. Dadurch musst du aber das Kabel aus dem Kanal raus holen und halt versetzen.
Once used once on your lawn, can you see the progress via the app like a robot vacuum? Since it can cut in straight lines and all means there should be a map on your lawn in the app and you can see where it is and maybe even send it to zone 1, 2 etc?
Try to change docking station position from normal to corner in advanced menu, it was the solution for me.
Thanks for the suggestion. Is that a setting in the App (as I can't find it there) or one set on the actual mower panel?
@@rusted99 ruclips.net/video/l9v5Vn0kTBw/видео.html
@@romkyy3542 Perfect, thanks!
I have the same problem. I dont have the setting for corner or default. Just installed mine today xs300
Is the "house" sold with the docking station or 3rd party?
Sold separately
Ein Problem das Bosh seit JAHRENDEN hat :-((( voll nervig, leg das kabel aus dem kanal raus, und setz es genau mittig in die Station und dann gehts perfekt
Der Draht führt leicht schräg in die Station und deswegen fährt er leicht schräg ein und trifft somit nicht die Ladepunkte. Zudem muss der Draht oben auch gerade verlegt werden, also von der Station gerade aus nach rechts, also es sollte ein 90 grad Winkel sein.
It is all correctly installed at 90 degrees. The solution for me was as suggesed by ROMKYY - changing the docking station position from "normal" to "corner" in the advanced menu.
Die Leitung vor der Station ist nicht perfekt gerade. Kenne das Problem. Oder die Station ist leicht schief.
Thanks for the suggestion. I am pretty sure it is all correctly installed. I used a spirit level to ensure it was perfectly flat and the wire runs in to the base station at 90 degrees.
@@rusted99 are you sure? I can’t see a 90 degree in the station (down to up) and the outgoing left to right) you need |_
@@markush.5669 Yep, all correct. The solution for me was as suggesed by ROMKYY - changing docking station position from "normal" to "corner" in the advanced menu.
Der Bosch Indigo S +500 leuft leider nicht 100%! Ja das mit dem Kabel habe ich jetzt auch versetzt aber bin der meiner das die Softwear sehr viele Probleme macht.
Ich hatte den gardena sileno City 250qm getestet und muss sagen, dass das mit dem leitkabel wo der Robert den weg zur Station sucht Sinn macht!
is that already resolved ?
Hi Jan, it seems to have worked out itself to reverse a little further and try again without leaving the garage. It normally docks successfully 2nd time around now. I tidied up the wires behind the dock which may have been interfering with the signal. Very happy with it otherwise. Very good navigation and cutting lines and restarting cut where last cut ended.
Bosch hat ein Problem mit der Digitalisierung. Alle ihre Geräte sind veraltet, weil es an IT Fachleuten mangelt. Ihre Apps sind immer zehn Jahre zurück geblieben als Dieter Chinesen.