Axe & Hammer Handle Replacement - How to do it OldSchool
HTML-код
- Опубликовано: 13 сен 2024
- repairs101.ca/...
How to do-it-yourself instructional on replacing wooden handles on axes and sledgehammers using traditional wooden wedges and steel wedge staking. #tools #axeandsledge #repairs
Transcript provided for the hearing impaired:
Alright so today on Repairs101 I've collected a whole bunch of tools over here that need their handles replaced and I've got a bunch of wooden handles and I'm going to show you how it's done.
So this is definitely an example of how not to secure your handle to your tool head. You want to get the old handle out by whatever means necessary.
It's critically important that you know where the bottom of the kerf is so that you can insert it properly into the tool head - so mark it with a pencil.
Fit the handle through a series of trials observing where the witness marks indicate the base of the tool head lands in relation to the bottom of the kerf.
Never pound the handle on the ground or hit it with a steel striking surface like a hammer, it will crack the handle base. Instead choose a nice beating stick from your firewood pile, something with a little heft.
You can use any number of tools to reduce the handle including the axe head itself. I've collected quite a number of rasps and rifflers over the years as I like to do the odd bit of wood carving. Or you could use some sandpaper, say one twenty grit or something even coarser.
Again, it's critically important that the base of the head extend at least a half an inch beyond the bottom of the kerf. You want a tight fit with no gaps showing.
A little carpenter's glue will make sure the wedge can never slip out.
Now I've seen a lot of different styles of steel wedge placement in the past and I think the lesson there is that there is no one way to do it. They say more than one road leads to Rome and hey it's true! Check it out there's even an airport.
You definitely want to counter-sink your steel wedges a little bit. You can turn a larger steel wedge diagonally to make sure it fits without touching on the edges. You see I didn't get this one quite centered but it'll be fine.
Recently I've been using Mineral Oil to protect wood because it's cheap, non-toxic and available at almost any pharmacy.
The only video where I have to pause instead of fast forwarding. Thank you for the awesome straight to the point information. I also like how you acknowledge that other methods are not wrong or not as good. Except for the ones you said where incorrect because of the damage or dangers they produce. Thanks again sir.
Exactly...when I look for a do it yourself video...I almost always pick the shortest one. It shouldn't take 18 minutes to show me how to replace an ax handle, THNX!!!
Almost 10 years since 1st posting, & its still educating and informing thus its timeless. Awsum !
very well done , the video get you into the point without wasting any time , that is how it should be done , thank you
most ismail Thanks! I remember working very hard on that one!
Well done. Short. Concise. Thank you.
Glad it helped!
I repaired my broken axe handle today with the help of your video. It turned out quite nice. Thank you very much!
Glad I could help!
Great instructional video. Thanks for getting straight to the the point, such a rarity on youtube these days.
Thanks!
This was awesome and surprisingly therapeutic. Great job!
thanks!
Haha, agree. ASMR for men.
Fast paced. Had to stop and rewind several times. Seems like good information and technique. Worth watching, thanks!
Glad it was helpful!
Excellent video ! Great sharing.
Th-up. I wish you a beautiful new week.
Many thanks! Best wishes.
the only video I'm aware of where it states how far the head should rest below the kerf! I am attempting my first restoration (Worthington/Mann Anniversary?) and was held up wondering how far past the kerf I should place the head. Good vid!
Rock on, Dick Burns (if indeed that is your real name).
When I saw the video was only 4 mins long,I knew what technique you were going to use.The same way one I was taught 50 years ago.the only way to do it and the tool head shaved the wood for a skin tight fit.And it’s rather speedy too!the hell with files and all that other time consuming stuff.Great job!
Great. Clear and concise!
Fast, simple and quality job. I did a maul right after watching this and the glue isn't even dry yet but know it is done right/
Rock on!
I love these old vids
Me too!
Thank you! Quite well done. You probably should have mentioned that burning the old handle out is NOT recommended. Thank you for the video!
You make a good point, Unclematt.
If you have a belt sander, turn it upside down on the bench and it can profile the handle very easily. Also it can be used to touch up the top of the handle sticking out before you install the wedge, making it perfectly flush.
Thanks for the tip!
Awesome video bro, thanks for the tips. I was able to fix an axe and a sledge hammer.
Glad I could help!
Something with a little heft hahaha awesome video thanks mate
Glad you enjoyed it. I've made over 150 videos but this is one of my personal faves!
Nice! Simple to the point instructions, many thanks sir.
Thumbs up for the Rome joke. I'm working on restoring grampa's old hatchet. Thanks!
Thanks Trevor! I often think my jokes go completely unnoticed. Good luck!
I also appreciated the tutorial. The joke was just icing on the cake. :-)
hey man that is very instructional video. i put a new haft on my axe for first time and i did decent. could be better. i feel alot more confident after seeing this video. i have quite the collection of axe heads, now time for some new handles. thanks
Rock on, Chad!
Thanks for the nifty information. I've always found it such a pain in the "proverbial" when I have to replace a broken axe or maul handle.
Happy to help, Allan.
Very nicely explained, thanks!
Good job, fast and to the point!!
Thanks, Bill.
When i was a kid. I always wondered why the top of an axe looked like that for? Now i know it is to make it sturdy and secured.
:)
Big big thanks for this video. Dad's old ax just snapped on me.! Boy was it a stress to get the handle off. My solution. Burn the sucker off. I just left it in the stove. Blackens the head but works.. Saves chipping away.
Simeon Banner Unfortunately you may have weakened the steel (or conversely may have hardened the steel) by exposing it to high temperatures. I'm no expert but mechanics are trained to keep their tools away from torches for fear of spoiling the temper. Good luck!
en.wikipedia.org/wiki/Tempering_%28metallurgy%29
This helped a lot
Glad it was helpful
Thanks for the video, I wish I saw it before I put a new handle on my axe , but I did get it pretty close. The glue is a nice tip, I appreciate the info, and your succinctness in conveying the proper techniques, something sadly missing these days!
Regards,
-Peter
Thanks Peter - I made lots of great videos check them out sometime when you get a chance!
Thank you, very well done
Thanks - have a look at the sequel - ruclips.net/video/B4cB_T7OxNY/видео.html
I recycled the sledge hammer handle you see me cut off in this video by carving it down for a rock hammer.
I also epoxy the handle on shovel and other socketed tools. Tool handle replacement is easy, but very few people do it.
I did not know the half inch rule thanks!
Rock on!
thanks for a great video eh, it made me a bit homesick eh. i‘ll replace my half-ax handle tomorrow, now that i know what to do. 🇨🇦🇨🇦🇨🇦
Beauty, eh? Rock on, Andrew!
Thank you sir.
Most welcome.
I like to fill any voids or recess in the end with clear resin or epoxy to prevent water getting in at the end and rotting it out prematurely. Looks pretty smick too I think.
Helpful wee video😬👍🏻
Glad to hear that
Very good. Thanks!
Glad you liked it!
Good info
Thanks
hey great video! I have a double bit michigan pattern axe and a regular cutting axe like yours. Thing is, they always slip out of the handle. I'm a young lad so I like to cut down big trees with them and I do it quite often. Is this a too heavy job for this handling technique? I'm gettin' real tired of always replacing handles!
Thanks, great info!
Awesome
Thanks!
I just repeatedly beat the wedge into my axe until there was no more wedge left. Without glue. Will that still work ?
Terrific ~ Thanks!
Glad you liked it!
Terrific!
Thank you.
You make no mention of proper grain orientation. My father taught me that the grain should run parallel to the striking direction, for greatest strength.
If you could answer a question I have I would appreciate it. Bassically, I am trying to find out what meterial/wood is best used for the wedge which is inserted into the top of the handle. I have read a few comments that suggest that soft wood is better than hard. Is that true? I am also wondering if useing hickery is applicable?
+qzetu - I never gave it a lot of thought before - I always just bought wedges in a package at the hardware store. But for sure they're always a "soft-hardwood". My guess is maybe willow or poplar, NOT an actual conifer softwood. As for why I think a hardwood might tend to pop out where the soft wedge grips. Hickory, on the other hand is very hard and used for handles.
+Repairs101 Thank you for your video and response.
:)
very good!!!
thank you
:)
Man you should sell your carvings. Great video. I've got some extra epoxy sitting around would that work better than wood glue by chance?
Thanks Mike! No problem using epoxy instead.
@@repairs101 thanks for the quick reply!
Some detail in here that most other vids miss
I know, right?
I am replacing 4 axe handles and 2 splitting maul handles, and I have been watching videos on hanging the tool heads and proper maintenance with linseed oil and all, but I cant find any information on applying paint on the handles. Some tools I notice have half red painted handles and I am wanting to do something similar for three reasons: First as a high visibility feature incase it gets dropped it will be easy to see in the leaves. Secondly, as a way to personalize the axe and make it mine and easily identifiable. And finally as a quick reference measuring point so that I know I have the right size log that will fit into the fireplace.
In what part of the process should I add paint? I assume it should be AFTER I have done the saturation with oil because once its on it wont take oil any more? But on that note, is it a bad idea to paint a handle since once it is painted it cant soak up any oil any more? After I have painted it will oiling the handle do anything to the wood where the paint is on it?
Thank you and hope to hear from you soon.
Gary Bowen A lot of people find painting the handle questionable but I think your reasoning for painting is airtight and i feel like you know what my answer(s) will be. I would probably look into a red primer and use it when the handle is clean, dry and sanded. I would lay the primer in several coats and a laquer topcoat for a durable finish. I would treat any remaining exposed wood as usual, treating it to frequent oilings. Keep in mind when applying oil only the surface is treated and a little sandpaper will reveal fresh untreated wood. Paint will work the same way, except by adding an exterior layer to seal the wood rather than making a layer of wood that sealing layer. Hope that makes sense.
Did people ever then soak the completed assembly in water to make the wood expand?
Yes ! However it's just a temporary fix cuz the wood shrinks back to normal once it dries. Soaking in oil has much longer lasting results.
@@repairs101 pheww, then my pops didn’t lie to me!
Split the top of my handle while driving in a steel wedge. Still seems tight, is this something that will compromise the longevity of the handle? And experience with this situation? Thanks
Yes, they do split. Me, I don't worry about it.
Assuming the split doesn't show on the handle side of the tool head you should have no problem.
Thank you much!
My husband uses a drill and drills out the broken handle that's left inside the head when its hard to knock out.
Thanks. I take it with the steel wedges, that you don't cut a kerf. Is that correct?
I always cut or use an existing kerf. See this other video of mine for more on this subject.
ruclips.net/video/B4cB_T7OxNY/видео.html
Good video. There are too many axe videos with out any information on them.
Glad you think so! I am quite proud of this vid but it never gained the traction it deserves.
Do you pound a steel wedge into the wood wedge, or do you use either wood or steel, but not both?
You drive the steel wedge into the wood wedge at 90 deg.
Can you use a screw to temporary keep the handle tight and if so please reply what kind of screw to use
Did you not watch the video?
I did my hatchet and when you look down the handle the head is leaning left is that bad?
I can't imagine how that would happen. Maybe too much material removed on one side? In any event my guess is it will be unreliable and perhaps even a hazard until sitting straight. I'd probably try again with another handle. Good luck!
Thanks for the fast reply it was just a cheap razorback hatchet handle I didn't remove any material at all really I think it was just cut wrong sucks tho cuz I've already put a lot of lindseed on.
ps: j'aimerais apprendre à bricoler, ça peut rendre service. je connais beaucoup de choses sur les plantes et les arbres mais pour le bricolage je suis nulle ! :X
Brilliant but slow it down a bit! Fair amount to take in
That's what pause is for.
ruclips.net/video/g0aC6xOppio/видео.html
Why didn't you just burn the handle off ?
You could ruin the temper of the axe head that way.
I just can't say it again , just great
You never put an axe from the side where it should end ,its gonna fall of.
Looks like you should have put the heads further down onto the shoulder. Two ways to skin a cat I guess.
get your mineral oil at a farm supply co, 1gal jug for next to nothing, I think i paid $12. Used as animal laxitive ;)
666dynomax Great tip! Thanks!
i like the abuse on the vice , cop on ffs.
You've got a lot of great information here, but you go WAY too fast for anyone to read the information provided. Slow down! You don't have to slog through things, but make sure there's enough time to read the words on screen before you move on to your next point.
Thanks for the tip. I made that video several years ago and hope my editing has improved since then.
@@repairs101 no problem! After watching, I managed to knock the broken haft out of my favorite single bit. Thanks!