That was amazing! Thank you for sharing your hard work! I have also repaired my own VCR recently but being an after 2000 model the lower and upper drum are one big replaceable component witch I just needed to pull it out and pop in place the new one. the only other thing I needed to do was to attach the drum motor witch sits on the top. I think that most VCR-s made after 2000 were intended to be easily repairable with as less adjustment as possible.
*Любой подобный ремонт обязательно нужно снимать на видеокамеру , чтобы потом в обратной последовательности можно было собрать до последнего винтика всё правильно* 👍
Hi i have a Panasonic VHS VCR, on SP the video is garbled, on LP, EP the picture is fine, tapes played on SP mode used to playback fine but now it doesn't what could be the issue. Thnx.
Excellent job! This is knowledge and skill that we need to preserve, thank you for making this video to share it. Do you just compare the old and new head under a microscope to find one with the correct gap width?
Now where can you get replacement video chip heads? The thing everyone must consider is that both the upper AND lower drum haven't worn down too much. The upper is dead easy but the lower drum the entrance/exits will ultimately determine the difference between the chips poking out of the drum too much. IT'S CRITICAL in operation that the tape uses that air between it and the drum surface to flow smoothly and the tape comes out of the machine 'undamaged' and not in fact using a worn surface and wearing or scratching the tape surface. It can be so easy to say the drum looks fine but also too easy to turn it into an instant cheese shredder and your precious tape is the victim and potentially unplayable.
Miso bro, I have a Panasonic VCR nv hd 620 whose head seems to have become disfunct due to wrong cleaning and wiping with cloth. Is a replacement head available in your city? I can pay online if it can be couriered to me in India. Pl advice.
Head dram replesment or head tip replesment ???/you are the only vcr teck person !!! Nice work cong !!,/tip replesment is a most dificult work for green and blue tip alingment ???
How about Hi-Fi adjustment after replacement, would that be ear and scope or more difficult? And afterwards the usual locking glue like for the a/c heads or a specific glue given its a moving part?
Hi Livinlifetothefullest2750 ! After head replacement , FM audio switching point also should be checked, if there is noise switching in Hi-Fi audio , please re-adjust again. To lock parts from moving, please use loctite.
I made it with S-VHS JVC S-6600U, but for years i need to do azimuth adjusts in heads till to play 4 heads and Hi-Fi sound. Much patiente because the true is that i need new complete Head to turn to perfect VCR. See my playlist "VHS, S-VHS, D-VHS - Memory Rescue"
Может кто-нибудь, пожалуйста, объяснить, разве головки подлежат износу? Ведь они не имеют прямого, физического контакта с лентой и из барабана не торчат. Как понимаю, головка меняется только в том случае, когда она была подвержена каким-либо механическим повреждениям.
Thanks, is there a way to remove the head and still be able to play the tape without image. I'm working on a project and need to put a similar tape (not video/audio tape) in VHS spools and just play, FF, RR.
Hi Morteza Parkook ! If you use the original tape transport control and servo circuit board , it will not work when remove the head drum block because of no drum rotate detection. In this case , video heads don't matter much for play the tape without image and it is no need to remove the head chips on the head drum. If you use your re-built control circuit , you can remove the head drum block.
Hi rsuryase ! We can use Video Head Chips of one brand on other brands , but must ensure that they must be the same type , Ex : SP head , LP head , SP/LP head , Hi-Fi head , Erase head , each type has azimuth and azimuth- pieces, they must be correct position.
Hello Misu how are you? Congratulations for your very instructive video and good quality and explanation. How do I get these heads? I'm in need of some.
Hi, I'm restoring a Hitachi VT-410 VCR and I noticed that one of the video head is broken. I found the upper cylinder replacement at a very cheap price, EUR 6.80, and I think to buy two of them and try to replace it. Is it really mandatory to use the comparator as you do on 8:43?
My Panasonic m3000 working but not play video properly i do track settings but thats not work i also clean heads nd settings the up side of heads jumper bolt what should i do can u please help me
Wow I didn't know VHS head drums require eccentricity adjustment like the early Betamax head disks. Does this also apply to other brands like JVC and Panasonic? Also it was nice to see a demonstration of video head dihedral adjustment! What's the tool called for doing dihedral adjustment (horizontal azimuth)?
Hi Fivos Sakellis ! This procedure can be applied to 80% of 70s, 80s, 90s common VCR models. Most of models produced after 2000 are often designed in "instant noodles style", which used 1 time and difficult to replace and align. To adjust the horizontal azimuth, I use an L-shaped eccentric stick. I bought this tool from a retired serviceman , I don't know its name or part number.
@@misu4602 Have you ever done dihedral adjustment on a Betamax video head? On the Betamax alignment tape, the monoscope section has the head switching point visible in the middle of the frame, and to adjust the horizontal azimuth, you look immediately below the switching point to see if the video fields split apart. The head disk on Beta VCRs has threaded holes and there are special conical-shaped screws that you put through the holes to shift the position of the head that way, instead of using an L-shaped key.
@@crashbandicoot4everr Betamax is not common in my country so I don't have experience in Betamax , I have never done dihedral adjustment in Betamax , I just fixed the locked drum problem.
Thank you for showing this and how you make the alignment on the single head! the FM packet from head A (changed head) is it near the same then the other head B but is the tiny difference in the FM packet the new head - in that case that it is new compare to the other head B? What for a head you're using for the head A? where did you know what is this for a head +6° or -6°? or is this the color that is on it? Thank you for this Video Thumbs up No.452 weakbit
Hello Weakbit ! There are many types of video head chips, their resistance and inductance is also different so the FM amplitude will also be different. We cannot find a replacement head that is the same as the original head, so after alignment , the FM amplitude between the changed head A and the original head B will not be exactly the same. The purpose of the alignment is to get the highest FM amplitude from the changed head. Video heads have positive and negative azimuth, and they have different color rules according to the manufacturer. According to experience, if the color pair is blue - green, then blue is negative, green is positive. If red-green pair, red is positive, green is negative. If green - yellow pair, then yellow is positive, green is negative. If blue - red pair, then red is positive, blue is negative. For example if the original pair (O) are "blue- green" , we can replace them with the new pair (N) : "green- red" that mean blue_O → green_N ; green_O → red_N (for reference) That is experience, may not be accurate as each manufacturer may be different. To be more certain, a microscope should be used to determine the azimuth angle.
Hi Chazlabrecque ! In 80's , Video heads were assemplied and adjusted by automatic robot arms. Please refer to this video : ruclips.net/video/gbBuBRY3iJ8/видео.html
@@misu4602 Thanks ..great video... I may attempt to replace my head element's but it's not an easy task to get it right..but it's not going to ever work if I don't try...thanks.
@@misu4602 In my country, the largest electronic spare parts store, decided one day to throw away all the spare parts from the VHS section. Twenty years may have passed since this event.
DO ĐẦU DAT KO THÔNG DỤNG NÊN NGƯỜI TA KO BÁN MÉP TỪ ĐỂ THAY THẾ ANH Ạ . THƯỜNG CÁC BỆNH Ở DAT ÍT LIÊN QUAN ĐẾN MÉP TỪ , CHỈ TRỪ TRƯỜNG HỢP VỠ TỪ DO LAU TỪ KO CẨN THẬN .
Hello!!! I found your video very informative. My video head is also broken and I want to repair it, but I can't get the repair parts. If you could tell me the names of the parts and where you bought them, that would be great. I'm Japanese so I'm not very good at English, but I hope you get the message.
Hi Aki san ! I'm from 越南 . Thanks for your interest in this work . For the best result in head replacement work , you could buy new video upper drum block to replace in your VCR, you will not have to do any delicate alignments but it is necessary to find right part number (please see in service manual of each model). If you can't buy right video upper drum block , you could do this work by replacing head chips (as this clip) , but this work need much delicate alignments. You need to buy new video head chips to do this work . Video head chips were sold in my country in the 90's as universal parts , they are general-purpose and can be compatible with most VCR models. I don't know their part number . I bought back the inventory of a electronic component seller . These video head chips are no longer manufactured and sold in the market but may be still stock in service center or 修理センターin 日本 . Please try contacting them for more informations.
@@prakashm1468 We can use Video Head Chips of one brand on other brands , but must ensure that they must be the same type , Ex : SP head , LP head , SP/LP head , Hi-Fi head , Erase head , each type has azimuth+ and azimuth- pieces, they must be correct in position.
Great video everything proven tvs are terrible now days y because people don't do good enough job on shoder now days everything proven VCR players are tilling on tvs now
If you replace the for heads make sure you replace wheel and heads,do not replace the heads by themselves good luck replacing just the heads,,,,they require in thousands clearance .
That was amazing! Thank you for sharing your hard work! I have also repaired my own VCR recently but being an after 2000 model the lower and upper drum are one big replaceable component witch I just needed to pull it out and pop in place the new one. the only other thing I needed to do was to attach the drum motor witch sits on the top. I think that most VCR-s made after 2000 were intended to be easily repairable with as less adjustment as possible.
*Любой подобный ремонт обязательно нужно снимать на видеокамеру , чтобы потом в обратной последовательности можно было собрать до последнего винтика всё правильно* 👍
Fascinating! all done without a microscope. Excellent work thanks for showing!
Hi i have a Panasonic VHS VCR, on SP the video is garbled, on LP, EP the picture is fine, tapes played on SP mode used to playback fine but now it doesn't what could be the issue. Thnx.
Excellent job! This is knowledge and skill that we need to preserve, thank you for making this video to share it. Do you just compare the old and new head under a microscope to find one with the correct gap width?
Hi probnot's tech ! I have never used microscope to see the correct gap before .
Awesome work Misu ❤️ you love what you do, i feel it.
Where in the earth do you get those heads?
Hi Hqdefault ! I was lucky enough to buy heads from a VCR service store. They have been stored in the storehouse for a long time.
I have many head chips ❤😊
Cám ơn em đã chia sẻ !
That great! I love your job ,when you careful and repair It. Hope i learning more from u.
Best wish from Vietnam.
Impresionante, todo s cálculo sin microscopio. Solo los orientales pueden hacer esas cosas, mis respetos.
Довольно трудоёмкий процесс!
И кропотливый ... но когда рука набита -это не сложно
Perfeito!
Obrigado por compartilhar!
Excellent work
Very nivel vídeo Misu! I really liked to see how those adjustments are done and un your video this os very nicelly shown , 😃
AMAZING!!!
what an incredible job, friend where concigo buys the heads you replaced
Fantastico.
Great job
Superb!
Now where can you get replacement video chip heads?
The thing everyone must consider is that both the upper AND lower drum haven't worn down too much.
The upper is dead easy but the lower drum the entrance/exits will ultimately determine the difference between the chips poking out of the drum too much.
IT'S CRITICAL in operation that the tape uses that air between it and the drum surface to flow smoothly and the tape comes out of the machine 'undamaged' and not in fact using a worn surface and wearing or scratching the tape surface.
It can be so easy to say the drum looks fine but also too easy to turn it into an instant cheese shredder and your precious tape is the victim and potentially unplayable.
VIDEO LINDO explica bem como recuperar cabeçote , tenho um canal de colecionador de vhs da uma visitada tem bastante coisa legal aqui do brasil
Miso bro, I have a Panasonic VCR nv hd 620 whose head seems to have become disfunct due to wrong cleaning and wiping with cloth. Is a replacement head available in your city? I can pay online if it can be couriered to me in India. Pl advice.
Bạn còn làm đầu video à , thay miểng , và gọi là cái trống , nhớ nghề quá , từ khoản 2005 về sau nầy mình không còn làm đầu video nữa .
Head dram replesment or head tip replesment ???/you are the only vcr teck person !!! Nice work cong !!,/tip replesment is a most dificult work for green and blue tip alingment ???
Very interesting video
Es tecnología obsoleta pero es vigente la habilidad y virtuosismo demostrado en este video me atrevería a decir que aquí he observado arte
How about Hi-Fi adjustment after replacement, would that be ear and scope or more difficult?
And afterwards the usual locking glue like for the a/c heads or a specific glue given its a moving part?
Hi Livinlifetothefullest2750 ! After head replacement , FM audio switching point also should be checked, if there is noise switching in Hi-Fi audio , please re-adjust again.
To lock parts from moving, please use loctite.
Thank Misu
Cool)
I made it with S-VHS JVC S-6600U, but for years i need to do azimuth adjusts in heads till to play 4 heads and Hi-Fi sound. Much patiente because the true is that i need new complete Head to turn to perfect VCR.
See my playlist "VHS, S-VHS, D-VHS - Memory Rescue"
👍👍👍
Hlo sir can you send me head tips for national panasonic j11 model
Может кто-нибудь, пожалуйста, объяснить, разве головки подлежат износу? Ведь они не имеют прямого, физического контакта с лентой и из барабана не торчат.
Как понимаю, головка меняется только в том случае, когда она была подвержена каким-либо механическим повреждениям.
Preasent New head spearparts avilabel?. Yours work super exlent.
Thanks, is there a way to remove the head and still be able to play the tape without image. I'm working on a project and need to put a similar tape (not video/audio tape) in VHS spools and just play, FF, RR.
Hi Morteza Parkook ! If you use the original tape transport control and servo circuit board , it will not work when remove the head drum block because of no drum rotate detection. In this case , video heads don't matter much for play the tape without image and it is no need to remove the head chips on the head drum. If you use your re-built control circuit , you can remove the head drum block.
Are the video heads compatible with most VHS VCRs? I assume each manufacturer has different head designs.
Hi rsuryase ! We can use Video Head Chips of one brand on other brands , but must ensure that they must be the same type , Ex : SP head , LP head , SP/LP head , Hi-Fi head , Erase head , each type has azimuth and azimuth- pieces, they must be correct position.
@@misu4602 So with the more recent VCRs like Panasonic HD620, it seems virtually impossible to perfectly align the Azimuthal setting of Head Chip..
Hello Misu how are you? Congratulations for your very instructive video and good quality and explanation. How do I get these heads? I'm in need of some.
Hi Neibollauf ! Thanks for your interested. You can contact to old service center , if lucky, these heads may be still in stock.
Hi, I'm restoring a Hitachi VT-410 VCR and I noticed that one of the video head is broken. I found the upper cylinder replacement at a very cheap price, EUR 6.80, and I think to buy two of them and try to replace it. Is it really mandatory to use the comparator as you do on 8:43?
This is the proper way
Đợi clip này lâu lắm rồi.Cảm ơn em đã chia sẻ.Em có bán mép từ không?Giá mỗi mép bao nhiêu vậy?
EM CHỈ MUA ĐỂ DỰ PHÒNG THÔI Ạ . GIÁ 1 CẶP MÉP GẤP 30 LẦN GIÁ TÔ HỦ TIẾU NĂM 1990 :))
Super
My Panasonic m3000 working but not play video properly i do track settings but thats not work i also clean heads nd settings the up side of heads jumper bolt what should i do can u please help me
Hi Jeson Bodn ! Please check the power supply, head amp section, main video PCB ... For Panasonic deck, please check and replace all bad capacitors.
Wow I didn't know VHS head drums require eccentricity adjustment like the early Betamax head disks. Does this also apply to other brands like JVC and Panasonic? Also it was nice to see a demonstration of video head dihedral adjustment! What's the tool called for doing dihedral adjustment (horizontal azimuth)?
Hi Fivos Sakellis ! This procedure can be applied to 80% of 70s, 80s, 90s common VCR models. Most of models produced after 2000 are often designed in "instant noodles style", which used 1 time and difficult to replace and align. To adjust the horizontal azimuth, I use an L-shaped eccentric stick. I bought this tool from a retired serviceman , I don't know its name or part number.
@@misu4602 Have you ever done dihedral adjustment on a Betamax video head? On the Betamax alignment tape, the monoscope section has the head switching point visible in the middle of the frame, and to adjust the horizontal azimuth, you look immediately below the switching point to see if the video fields split apart. The head disk on Beta VCRs has threaded holes and there are special conical-shaped screws that you put through the holes to shift the position of the head that way, instead of using an L-shaped key.
@@crashbandicoot4everr Betamax is not common in my country so I don't have experience in Betamax , I have never done dihedral adjustment in Betamax , I just fixed the locked drum problem.
Thank you for showing this and how you make the alignment on the single head! the FM packet from head A (changed head) is it near the same then the other head B but is the tiny difference in the FM packet the new head - in that case that it is new compare to the other head B? What for a head you're using for the head A? where did you know what is this for a head +6° or -6°? or is this the color that is on it? Thank you for this Video Thumbs up No.452 weakbit
Hello Weakbit ! There are many types of video head chips, their resistance and inductance is also different so the FM amplitude will also be different. We cannot find a replacement head that is the same as the original head, so after alignment , the FM amplitude between the changed head A and the original head B will not be exactly the same. The purpose of the alignment is to get the highest FM amplitude from the changed head.
Video heads have positive and negative azimuth, and they have different color rules according to the manufacturer. According to experience, if the color pair is blue - green, then blue is negative, green is positive.
If red-green pair, red is positive, green is negative.
If green - yellow pair, then yellow is positive, green is negative.
If blue - red pair, then red is positive, blue is negative.
For example if the original pair (O) are "blue- green" , we can replace them with the new pair (N) : "green- red"
that mean blue_O → green_N ; green_O → red_N
(for reference)
That is experience, may not be accurate as each manufacturer may be different. To be more certain, a microscope should be used to determine the azimuth angle.
Cam on ban...!
I always wondered how they got adjusted... are all the heads the same??? as in the replacement elements?
Hi Chazlabrecque ! In 80's , Video heads were assemplied and adjusted by automatic robot arms. Please refer to this video : ruclips.net/video/gbBuBRY3iJ8/видео.html
@@misu4602 Thanks ..great video... I may attempt to replace my head element's but it's not an easy task to get it right..but it's not going to ever work if I don't try...thanks.
Em có bán đầu VHS không
Kỳ công quá,bây h muốn thay nhưng từ ko có
This is doable? Oh my god this is amazing!
*Think you could take on a Betamax head? 😏*
The basic processing of Betamax head replacement is the same as VHS but Betamax is mor difficult. I'm going to learn about this process.
I love you
A MISU có sửa đau vhs a sua cho e con đau sony slv_ kh3 voi
不过中国SONY的老前辈告诉我。色度磁头在SONY专业VTR可以替换。亮度不可以
Toi cung co may con xs1990 2000 doi sau nay , dau tu no cung kem doi
Is there anywhere you can still buy these chips at?
Head chips and gear parts are still inventory at VCR repair service centers but now becoming to probably rare.
@@misu4602 In my country, the largest electronic spare parts store, decided one day to throw away all the spare parts from the VHS section. Twenty years may have passed since this event.
Đúng là quá chuẩn , cho anh hỏi ngoài tí . Đầu DAT Sony có thay mép từ được kg em .
DO ĐẦU DAT KO THÔNG DỤNG NÊN NGƯỜI TA KO BÁN MÉP TỪ ĐỂ THAY THẾ ANH Ạ . THƯỜNG CÁC BỆNH Ở DAT ÍT LIÊN QUAN ĐẾN MÉP TỪ , CHỈ TRỪ TRƯỜNG HỢP VỠ TỪ DO LAU TỪ KO CẨN THẬN .
@@misu4602 Ok cảm ơn em .
Có đauban không?
where can i find those video heads
Hi Mubeen Farooq ! I was lucky enough to buy heads from a VCR service store. They have been stored in the storehouse for a long time.
Hello!!! I found your video very informative. My video head is also broken and I want to repair it, but I can't get the repair parts. If you could tell me the names of the parts and where you bought them, that would be great.
I'm Japanese so I'm not very good at English, but I hope you get the message.
Hi Aki san ! I'm from 越南 . Thanks for your interest in this work .
For the best result in head replacement work , you could buy new video upper drum block to replace in your VCR, you will not have to do any delicate alignments but it is necessary to find right part number (please see in service manual of each model).
If you can't buy right video upper drum block , you could do this work by replacing head chips (as this clip) , but this work need much delicate alignments. You need to buy new video head chips to do this work . Video head chips were sold in my country in the 90's as universal parts , they are general-purpose and can be compatible with most VCR models. I don't know their part number . I bought back the inventory of a electronic component seller . These video head chips are no longer manufactured and sold in the market but may be still stock in service center or 修理センターin 日本 . Please try contacting them for more informations.
@@misu4602 Thanks for the reply!
I'll use it as a reference and do my best to get that VHS deck fixed!
Sir maray ko g10 VCR or g3o VCR ka hade chahiya
Where can I buy such a jig?
Hi Ilan Uriel ! Please contact the electronic repair service center. If lucky, they still have stock.
Вы видели эту ржавую отвёртку😂
Halo
rum từ không quay là bệnh gì vậy chú
KEO BỊ LÃO HÓA KHIẾN BONG RA VÀ TĂNG MA SÁT . ANH THAM KHẢO CLIP NÀY : ruclips.net/video/sU3-b6iGze8/видео.html
You can still buy new video heads? Wow
Hi Louis Ho ! I just collect video heads for replacing when needed.
@@misu4602 so there is no source to order video head chip components from?
@@prakashm1468 I think new head chip components may be stocked in some old vcr service center . But they will be rare.
@@misu4602 forgot to ask...can we use Video Head Chips of a brand of VCR,say Sony, on other brands like Panasonic, Toshiba? I mean VHS to VHS
@@prakashm1468 We can use Video Head Chips of one brand on other brands , but must ensure that they must be the same type , Ex : SP head , LP head , SP/LP head , Hi-Fi head , Erase head , each type has azimuth+ and azimuth- pieces, they must be correct in position.
Do you sell Video Head Chips?
Hi DomaKingdom ! Sorry , I don't sell Video Head Chips.
Do you know where can a I purchase them from?
@@TriMightyOutreach Hi DomaKingdom ! You can contact to old service center , if lucky, these heads may be still in stock.
Sir.funaivhs player model 3000A Japan 1985 service sir ❤
My vcr head you repair p88 head Hathei
Great video everything proven tvs are terrible now days y because people don't do good enough job on shoder now days everything proven VCR players are tilling on tvs now
Ino. Cicho. Okei. Byle. Tak. Dalei
I want VCR head can you sell me?
This is I want
Please sell this miso
Where in the h*ll can we find replacement heads ?
Hi Edercarneiro ! We can find head chips at old video service centers . Please trying contact them , if lucky , they still store.
5sztuk
If you replace the for heads make sure you replace wheel and heads,do not replace the heads by themselves good luck replacing just the heads,,,,they require in thousands clearance .
Как по осциллографу настраивать никто в рашке не знает 12:00 *А тут реально МАСТЕР* 👍