High current induction heater , Powerful induction heater using mosfet IRFZ44N
HTML-код
- Опубликовано: 4 окт 2024
- High current induction heater , Powerful induction heater using mosfet IRFZ44N
Related Videos
1. How to make DC motor at home , homemade electric motor easy
• How to make DC motor a...
2.How to create robotic at home , Homemade small robot 2017
• How to create robotic ...
3.How to make soldering iron using lighter
• How to make soldering ...
4.How to make scrill machine at home using spray can and small motor
• How to make scrill mac...
5.Homemade a small and fast car for kids
• Homemade a small and f...
6.How to make 220V solinoid engine at home
• How to make 220V solin...
7.How to make super transformer at home
• How to make super tran...
8.How to make foam cutter at home
• How to make foam cutte...
9.How to make mini grill stove at home
• How to make a mini gri...
10.Free energy device
• Free energy device new...
11.Boost converter using small NPN transistor and 1.5 V AA battery
• Boost converter using ...
12.Motor as generator 2017, Homemade generator from DC motor
• Motor as generator 201...
13.Motor as generator , Homemade motor generator from old vcd player
• Motor as generator , H...
14.Motor as generator from small motor, Energy of small motor homemade 2017
• Motor as generator fro...
15. How to make scrill machine using 12V DC motor very easy , homemade scrill tool 2017
• How to make scrill mac...
16.V3 Solinoid engine whit 3 7 V, A powerful machine made in 2017
• Video
17.Wireless Electricity Transmission Review made in 2017 , New Project 2017
• Wireless Electricity T...
18.How to make electricity wireless transmittion 2017 step by step
• How to make electricit...
19.How to make Easy motor at home 2017
• How to make Easy motor...
20. Phone charging using small battery
• Phone charging using s...
21.Free energy , from small to a powerful energy, Phone charging using 1 5V AAA small battery
• Free energy , from sma...
22.How to make a powerful air pump at home very very strong
• How to make a powerful...
23.How to make 3V Battery from coopper wire
• How to make 3V Battery...
24.How to make mini Hydrogen Generator at home very easy
• How to make mini Hydro...
25.How to make an Electricity Generator from old HDD motor
• How to make an Electri...
26.How to make a mini flashlight 5W
• How to make a mini fla...
27.Amazing life hack , Easy way to cut roof (Zn panel) using wire
• Video
28.My Electronic lock desk , new idea created in 2017
• My Electronic lock des...
29.Free Energy , Homemade Free Energy Device From Syringe And Water
• Free Energy , Homemad...
30.Free Energy , Free Energy from magnetic, magnet motor 2017
• Free Energy , Free Ene...
31.Free Energy , How to make solar cell from LED, LED Vs Solar cell, homemade 2017
• Free Energy , How to m...
32.Free Energy , solar energy, capacitor charging LED as solar cell
• Free Energy , solar en...
33.Free Energy, Solar Energy, homemade easy solar cell 2017
• Free Energy, Solar Ene...
34.Quad motor helicopter Vs Single motor helicopter, homemade mini helicopters
• Quad motor helicopter ...
35.How to make V2 water pump at home , new model of water pump 2017
• Video
36.How to upgrade 3v DC motor to a high speed and strong motor
• How to upgrade 3v DC m...
37.How to make a mini water pump at home very easy, Homemade 2017
• How to make a mini wat...
38.homemade easy motor from CD panel 2017, a strange motor for 2017
• homemade easy motor fr...
39.ir remote control testing up to 40 meters range, homemade ir remote control without any ic
• ir remote control test...
40.High voletage capacitor, super capacitor , how to charge capacitor
• High voletage capacito...
41.Super motor , homemade easy motor 2017 , new idea to create motor
• Video
42.Free energy, solar copper wire, new idea to create solar cell
• Free energy, solar cop...
43.Very small battery, how to make a small battery at home very easy
• Very small battery, ho...
44.Homemade scrill machine very easy 2017 , a powerful tool
• Homemade drill machin...
45.homemade coilgun , a powerful coilgun 2017 part 1
• homemade coilgun , a p...
46.Homemade coilgun, a powerful coilgun 2017 (part 2)
• Video
47.Free energy, diode as solar cell, new idea to make solar cell 2017
• Free energy, diode as ...
48.How to make spot welding machine at home 2017
• How to make spot weldi...
49.Free energy , Transistor solar cell, how to make solar cell from transistor 2017
• Free energy , Transist...
50.Water turbine generator , not free energy , but just energy of water
• Water turbine generato...
51.How to make mini speakers using Beer cans
• Video
52.Lemons battery, how to make battery from lemons
• Lemons battery, how to...
53.Super DC motor, how to make DC motor very easy
• Video
54.Free energy, solar X4 diode , homemade solar cell from diode 2017
• Video
I have built this design for experimentation and funny thing, I soldered the capacitor with legs uncut and I saw smoke coming from the cap, but the capacitor was cold, after looking at it from another angle I saw that the leg of the capacitor was heating up, just one leg. I cut the legs as short as possible and it worked without smoking itself.
Could you show the components you used?
درودوسپاس.زیباوعالی بود.ممنونم🎉🎉🎉
very nice yaar, itna achaa video banaya aapne ki mai aapka fan hogya
Good idea Sir
WELL DONE YOUNG MAN IS VERY GOOD INDUCTION HEATER AND IT WORKS.
I MADE ONE TO REMOVE RUST NUTS AND BOLTS FROM CARS.
THANK YOU AND GOD BLESS YOU.
Thank you so much ....i bought some induction heater from China but it burnt
I mad one with your design for my project and it works good..thanks again
Standing ovation. I am totally impressed and speechless. Bravo!
I like induction becous that verry amazing, please make us ur make do induction for cooking make by the induction and try make doing cooking
Aisa induction 3.7 volt se chalne wala bhi ban sakta hai kya bhai???
Awesome. Just what I was looking for lol
Excellent project
Thanks, but the diode can’t handle more than 1 amp. Try using other fast switching, high current diode other than that, it’s a good circuit
Nice vidio great instructor for education
❤❤❤thx it works
It is so usefull to ame.
Thanks.
i would build the circuit on a printed board, this is very messy work..but it's interesting nonetheless.
its very good heater
Anak anak muda Indonesia sangat pintar dan cerdas
Can we use a bunch of copper wire instead of 2mm copper wire?
Hola, buen trabajo. ¿Sabes cuánta corriente consume al calentar? Debe ser de un par de amperes al menos. Saludos.
Wow... it was good ...
The complex connection of the circuit was osm. Use of resistor and capacitor are too good in less space.
At the last Osm.
hello the warchief
1 what is the best to use battery or powersupply
2-is this circuit operated on melting the metal such as iron
hi there
Nice to meet you 😊
Btw. I thought power supply is much better than a battery because you can increase or decrease voltage and current according to need
And second thing it can be used for melting iron but it take a lot time. In small scale you can melt the iron but in large on it's hard and you need high current and volt.
So,I thought you get your questions answer
Thanks!
Have a good day dear ☺
you all the thanks and appreciation
thanks
@@ahmedramzyabdelhady9398 Using solder not iron plz.
@@Hrshu_Singh can we make this type of induction heater using (v-!@V battery for small purposes??
Great video and teaching
Dear friend, it is so good .
I made one of these works perfect!
Really, I used breadboard for connections, not working
My power supply trips
@@karthickstarprince9823 there is free energy videos in his channel😆
Please can you help me with the tested circuit
Bro what's the input current 12v 2 Amps or 200 mA??
Very very best video
it really works!
I like it
perfect 👌👍🤝
*_Super, Bravo._*
شكر على مجهودك
very nice
Fantástico meu irmão!
I always watch ur vidio ur videos. R amazing
nice...
Hi, can I have a question? As I know, only alternating magnetic field (generating from AC) can heat magnetic material. How can your inductor heat magnetic material while the input is DC? Thanks.
Thanks for video.
why cant someone make 1 of these to anneal brass for 308 winchester? Better than a blow torch and spin it for 4 secs !
Hi Ray, this is precisely what we intent doing once I get the heater working. I am using a micro wafe transformer for PSU.
Can we use it for soldering iron
Cám ơn anh nhiều
i lovers american tehcnology
Maybe a daft question but how would I upscale this to get bolts red hot?? M8 and m10 bolts.
Use 6 × 0.33uf mkp x2 capacitor in parallel and increase supply voltage to 36 or 48 volts and change MOSFET to IRFP260N
Also change the single inductor to 2 centre tapped inductors and use a hollow copper tube for heating coil and water cool it
International Rectifier advises that a five to ten ohm resistor should be used in series with the gates of Hexfets and the driving circuitry in switching topologies. Such a resistor prevents ringing oscillations that can puncture the thin oxide gate.....
Your making very good videos but
Thanks you
What frequency it is oscillating?
don't fall in illusion, PET and MKP film type are very different in looses(and efficiency)
when there 12VDC or 12VAC*50Hz or 12VDC+1VAC*1kHz Polyester(PET = mylar film) will work too
if you need oscillator collecting energy of each stroke - swinging in resonance mode to ten times bigger current or voltage in RLC circuit - you don't allow extra dissipation, and on HF HV AC you definitely need MKP(Polypropylene film type), or also good will be Polystyrene, Teflone, mica or vacuum capacitor types, but PETF will work just little faster than electrolytic capacitors, advantages of PET vs electrolytic capacitors is only: not afraid of pretty often(not very often really - like 50-100Hz) short circuit discharge, polarity independent and store(not loosing if you will not take it in and out every millisecond)) charge longer(problem only if you want to full AC recharge them to rated +-2000v 1000Hz or faster,
difference PET MKP in oscillator LC on 3000Hz only, 400V 0.01 PET: from 20VAC swing to 60VAC and burning by 100Wt of looses in 1 minute, when 400v 0.01 MKP from 20VAC 3000Hz(serial with car ignition "12v" coil -on peak resonance freq) collecting 10-15 periods reaching swinging voltage(on cap and on serial first low voltage-side coil same) 200VAC(3000Hz) and staying cool as RT, provide 15mm loud 3000Hz sounding arc on Hv side of car ignition transformator(from 100Wt*4 Ohm amplyfier with usual soundcard and program generator- searching most powerfull(resonant) freq , freq with all type of capacitor material remains the same(only microfarads is meaningful), but result of collecting swinging are differ...)
(h t t p s : / / w w w .) alibaba.com/product-detail/cbb81-Capacitor-High-Voltage-2000V-223j_62092555579.html - it is cheap PET caps - advantage - when you put it on supply 12V of your sound player - it will not allow any sound on 12V and little compared to MKP:
(h t t p s : / / w w w . ) amazon.com/capacitor-0-022uF-Metallized-Polypropylene-Capacitor/dp/B07RWSLZ35
that are cost more, bigger size always approximately twice bigger than PET size, and loosing ten times less energy when full recharge in LC oscilating circuit higher than 1kHz
sometime difficult do differentiate types - you have to know price and size - can not be little with MKP - for a reason - more plastic and metall inside, due to less strong PP properties against high voltage break compared with PET(better isolator - not brokes but leackage of charge on PET (when recharge moments) occurs more)
and 1n4007 - 50Hz diodes, they will not close fast even on 30kHz, so you really use them there more like a kind of resistor - that can disconnect after some 1ms delay, try to put some kind of ultrafast diodes UF.... HER... or Shotkey diodes - that faster of all - but low voltage and have bigger leakage when close than UF , some time meanyngfull but usually less meaningfull than speed of closing that they provide
1n4007 i saw in USB charger on 220VAC side rectification 50hz, but on output of pulse transformator on 500khz even econom chineese put ultrafast one diod for rectification, otherwice you will not understand - why no power i can get from pulse chematic
maybe does not mean in this heater gate chains,,,
Perfect video excellent bro. Jeep it up.
You make it looks so clean.
very good
Amazing!
Nice work
I can use d882 trangister?
Nice video
I get the reason for the big coil, but why the other smaller one wrapped around the plastic doughnut?
Perfect 👍👍👍
Good.
... not entirely sure here, but the middle leg of each of the transistors might be short-circuited through the tab that is screwed to each of the heat sinks; I might suggest that the heat sinks not be glued together.
sabe se posso usar o IRL Z14 no lugar do IRFZ44N ?
Any experience with this in terms of how much power is needed for let's say a 1cm broad and 3 cm long iron rod to bring it up to 350 C?
Muy bueno!!!!
nice👌👌👌👌👌👌
This layout is right
Any possibility to change frequency? because frequency make the things. thanks for the share.
Change the capacitor values
De cuantos amp tiene que ser la fuente? Se que es 12v. Pero los amperes??????
Dependera de los MOSFET que uses
Plier and scissors?? Hmm....anyway it works.
Very nice video, just one question - what value was the capacitor?
Briefly shown at 0:14 - 22nf (.022 uf).
@@WendyStringer48088 22 nf 2kv
Keep in mind This capacitor won't last very long
Hey friend! I love everything you do. But the music is unbearable. It's like torture! I have to go through it to watch your videos. Just if there is something you can do to resolve the problem ... thank you very much. courage 👍🏾👍🏾👍🏾
Bro what's the input current 12v 2 Amps or 200 mA??
does it heat organic?
How does this work with a DC power supply?
А на какой диаметр цилиндра из пластмассы ты наматывал heating coil? Индуктивность вспомогательной катушки равна 50 mkH?
But MOSFET lids must be as short as possible especialy source and gate
What Is the Green thing?
Can this melt metal (aluminum, copper)?
Is induction price kya hai
very nice, but I wish you would provide data on the toroid (nH/n², material, or just a link so we could look it up ourselves)
good circuit drawing
We have tried this project according to your guidance of circuit and components but when we gave supply of 12v dc battery for testing it then MOSFETs and Diodes blown out
Please help us
Check if you connected the diodes with right polarity. Also use UF4007 diode
ill put it to the test an let u know if it needs help or just for show or nothing.true story.
Pls sir I just need help from u pls don't ignore.
I just want to know how to create an engineering channel in RUclips and how to post them the right way, even knowing how get more views and subscribers.
Thanks
Primário da bobina de Tesla 😃
name American tech. but don't know to soldering. which soldering iron bit is used for it
Can we use any other capasitor?
Use 6 × 0.33uf MKP X2 capacitors in parallel for best performance.
you didnt say the wattage of the resistors, or what gauge of wire you used, and you forgot to put thermal paste on the transistors to help conduct heat to the heat sinks.... the heatsinks arnt big enough either... its still a nice idea though... but if people do this to the t it wont last very long...
Oh no call the police he didn’t put thermal paste
The whole thing is very low power
Can you make non touch induction solder iron ?
Great!
And... the Zener diode ? Without Zener
Dear sir great idea but show the numbers of wire gauge not show in mm please.
AWG 12
Hello, I tried replicating this in breadboard with all the components. The problem is when power supply is connected it is dropping down to milli volts instead of 12V supply and the coil is not heating. Can you please provide some explanation to this or any better solution.
Can someone please tell me does this experiment work only if soldered. I tried using all the exact same components including 22nf capacitor. Kindly reply on this! When done on breadboard the above experiment does not work?
Nyc bro
Keep it up!👍👍
The quiescent current i think is 200mA without any metallic object.What is the current consuption while heating the metal?
Which metal should I use as a work piece ?
Explicadissimo 👍
dá pra fazer um ferro de solda pra circuitos eletronicos
Plz change your MUSIC.
kkkkkk
Never watch his videos with sound. always take off ur headphones for his videos. he never speaks also he never replies to comments
I don't know where people find this "music" - it is literally goof, stupid music - like for an idiot bumbling about. Why not some motivational classical? Handel's Water Music? or a nice Beethoven symphony if you can't come up with your own pic. I get the impression that people who use music like in this video have no appreciation for music. Even Death Metal would be better.
@@NoferTrunions youtube and their demonitization bot explains it
Yes broo
I question the widespread practice, that i see with these induction heater projects, of using solder to bridge high current electrical connections.
Solder is a relatively poor conductor of electricity, and there is appreciable voltage drop across such a bridge connection. Good engineering practice dictates that high current connections should be securely wrapped with substantial contact between the metals of the conductors. Solder is then used to form a coating around the solid connection, to prevent oxidation in the future. Not as the structural connection.....
Koje budućnosti? Ovo je napravljeno da radi par minuta i onda na hlađenje😂
Perfect
Can i use 4n65 mosfet?
ढाई सौ वोल्टेज पर कैसे चलाएं
hi these can use for induction stuve? very good
Its very low powered for that