I ended up here watching your video because my harness and diagram for the extension kit was different from the original harness just the same. I'm curious whether or not you have had a chance to use the laser itself yet or not and if everything is working correctly. The one 12v wire per the wiring diagram show to disconnect the emergency stop switch. Let me know how it's going. Thanks.
We had to relocate the 12v wire for the emergency stop switch to another location on the motherboard as it was shown in the schematic in the manual. Everything is working correctly and we have been getting some nice results. Thanks for your comment and let us know how it goes!
Hi did you have any issues with the cuts not lining up? I got the extension kit installed a couple days ago and I've been having issues with it not cutting circles (turns to ovals) and the cuts not lining up or not being able to make correct curves.
It sounds like one of your belts is too tight or too loose. You may need to adjust your eccentric nut or your belts. Check out the video we have put below for help on how to make these adjustments. The title of the video in case the link does not work is... How to adjust the Eccentric Nut and the Belt about Atezr Laser Engraver. It's on Atezr's RUclips channel and even though it is the not the extension you should be able to apply it to the extension. ruclips.net/video/v46nmZWQH7w/видео.htmlsi=ae3Bm9fYjRhrRcZb I will also link this video in the description so you can find it... Hope this helps! 😀
@@tranquilmentor I’ve tried it all 😩 I’ve spent 2 days and have: 1. Loosen and tightened belts to correct setting. 2. Loosen and tightened eccentric notes to correct setting. 3. Made sure the frame was squared. 4. Made sure the gantry was square. It sucks because before rhe extension everything worked flawlessly
@@tamaramarrero9024 Sorry you are going through this ... it can be frustrating. Not sure if this would help but maybe you can check the rod and make sure its tight. The rod may be loose or too tight. It may be slipping. And maybe when you run the cut again you can position yourself right in front of the laser where you can see what the problem is. Look really close to see if you can find where it is messing up. Another thing that we did was we put the entire laser on a 3/4 inch piece of MDF which was not cheap and we made sure that the table was level by checking it with a level. We ended up having to add some shims to the back. Hope this helps!
I ended up here watching your video because my harness and diagram for the extension kit was different from the original harness just the same. I'm curious whether or not you have had a chance to use the laser itself yet or not and if everything is working correctly. The one 12v wire per the wiring diagram show to disconnect the emergency stop switch. Let me know how it's going. Thanks.
We had to relocate the 12v wire for the emergency stop switch to another location on the motherboard as it was shown in the schematic in the manual. Everything is working correctly and we have been getting some nice results. Thanks for your comment and let us know how it goes!
Hi did you have any issues with the cuts not lining up? I got the extension kit installed a couple days ago and I've been having issues with it not cutting circles (turns to ovals) and the cuts not lining up or not being able to make correct curves.
It sounds like one of your belts is too tight or too loose. You may need to adjust your eccentric nut or your belts. Check out the video we have put below for help on how to make these adjustments.
The title of the video in case the link does not work is... How to adjust the Eccentric Nut and the Belt about Atezr Laser Engraver. It's on Atezr's RUclips channel and even though it is the not the extension you should be able to apply it to the extension.
ruclips.net/video/v46nmZWQH7w/видео.htmlsi=ae3Bm9fYjRhrRcZb
I will also link this video in the description so you can find it... Hope this helps!
😀
@@tranquilmentor I’ve tried it all 😩 I’ve spent 2 days and have:
1. Loosen and tightened belts to correct setting.
2. Loosen and tightened eccentric notes to correct setting.
3. Made sure the frame was squared.
4. Made sure the gantry was square.
It sucks because before rhe extension everything worked flawlessly
@@tamaramarrero9024 Sorry you are going through this ... it can be frustrating.
Not sure if this would help but maybe you can check the rod and make sure its tight. The rod may be loose or too tight. It may be slipping.
And maybe when you run the cut again you can position yourself right in front of the laser where you can see what the problem is. Look really close to see if you can find where it is messing up.
Another thing that we did was we put the entire laser on a 3/4 inch piece of MDF which was not cheap and we made sure that the table was level by checking it with a level. We ended up having to add some shims to the back.
Hope this helps!