Fantastic video! I spent days trying to get the info in this video from Laguna videos and documentation with no luck. Thank you for putting all this out there!
Dude! I can't tell you how happy I am to find this video! Been operating a couple grizzly machines at work for months and yes going crazy trying to figure out/find info on pulling feed rates from code and using z probe! Manuals have been pretty confusing/useless and most of the videos I've watched are about the same. Thank you so much for this!
Thanks for this video. You have saved a lot of people a lot of time. As you say, it's insane that these good machines some with virtually no documentation so thanks again. BTW, you can control spindle speed dorectoly from your G code. You have 8 possible speed, (S) presets in the handset which you can program to whatever spindle speed you want. Say you want to run a 12000 mm/min, make that, say S2, and specify 12000 in your G code. As long as the handset has that speed allocated to an S number, it will follow the Gcode.. Thanks again.
Are you able to change speeds via your pendant, or only via G-code? I haven’t been able to get either to work. I've set G Code Setup > S Read = ReadS, configured the values for Machine Setup > Spindle Setup to allow 8 different speeds, but adjusting the spindle "gear" (as RichAuto calls it) either via the pendant (using ON/OFF + Z+/Z-) or via G-Code (i.e. M03 S12000) still has absolutely no effect on the actual spindle speed. When running the program, the controller correctly detects the speed indicated in the G-code and displays S3 (which is what I have set for 12000 rpm), but the spindle itself reaches 22500 rpm (since I have the VFD set to 375), and the difference is clearly audible.
@@StevenRosburg Hi, I export my code using a 'Richauto' post processor, (from Fusion 360) and provided I've specified matching spindle speeds in the CAM paths, it works.
@@Sentientfx1 okay, thanks. I’m going to have to keep digging then, because I’ve tried G-code that’s generated from Fusion 360 as well as hand-written G-code where the spindle speed matches one of the values configured in the pendant, and while the pendant recognizes the speed by displaying the appropriate spindle setting (e.g. S3), the VFD either never gets the message or ignores it.
Thank you thank you thank you bro I’ve been running rich auto on couple machines I even upgraded one completely it’s an excellent system. I still manage to learn something from you. Cheers, Ziggi from Australia
Thanks this is the most comprehensive video I have seen. I did change my settings in pro settings like you suggested. Just got my machine. Thanks Again What is the black knob for on the electrical control box close to the RPM adjustment at the end of the video
Hi, thank you, I have a Richauto A11 and when I click on the file I want to run it loads but immediately then goes to a "line no 1" on screen, when I then press "run" + "1" it does nothing. According to other videos it should start but does nothing. I am very frustrated to the point of wanting to sell my machine.
Ok so lets try and break this down, my first question would be when you click run/pause and the green button on the program does it bring up the set work parameters screen? If it does are you saying after you hit the green go button from the set work parameters screen it does nothing? If so my next question would be, what CAM package are you using to generate your Gcode? Then my next question would be what post processor are you using in that CAM package to generate the Gcode? If your using a vectric product with the correct post then that's a dilemma, I would suggest viewing the Gcode on the machine and checking to see what the first few lines are. My theory is, there might be something in the Gcode that is stopping it from running. Let me know what you encounter and we could try to move on from there. What machine are you using the A11 control system on?
When I press the toolset buttons the cutter moves up instead of down. When I touch the cutter with the touch plate the z axis stops and retracts the set distance. I have auto updated but that did not resolve the issue. Thanks
I would start by checking the gcode to see if the Z move to that height is in there. That way you can rule out if it's a post processor or software issue first.
@@WadeMade my neighbor has a Laguna Swift 4x4 and I’ve gone over your video with him and he is also very thankful of your videos. I’ve been helping him because I have experience running Haas cnc. We both can’t wait for your next video.
Appreciate the video and all of the advice. I am literally using my Laguna IQ for the first time and I cannot figure out why the puck is not zeroing out Z axis properly. Every time I touch off the puck, the spindle run height is at least an inch or more higher than the work piece. I have abandoned the puck and am just lowering the spindle to the point of touching the work piece and setting Z0 manually. I did go in and tried to set the C.A.D. thickness to the actual puck height of approx 25mm. But that just added even more height to the Z zero when touching off. Any thoughts on how to fix?
I'm sorry to hear your having trouble. I haven't been on my machine in a while but maybe there was a software version change. When you entered the thickness in the C.A.D. thickness on the setting page did you enter a positive or negative number? Whatever you entered I'd try the opposite. But when you go to test it keep an eye on the height so you don't accidentally plunge anything or notice any weird behavior. Maybe hold the puck in the air for the first test. Also make sure you enter the thickness in millimeters. I hope that helps.
@WadeWade Please tell me how to control the fall speed after it starts working because mine it's falling down and working very fast and I don't find the option to set it to fall somehow slower... It breaks my motor and my drill heads. I tried to set "Ignore to all" I set my fall speed to 0.1, the Speed scale to 0.5, the Work speed 1000 and still it's going super fast down while cutting sideways... This sideway cut feels like forced and that's why the machine bends my heads and breaks them. Btw I am using it for marble carving, so it's not a drill bit, it's more for sculpting and creating shapes. Thanks in advance!
First thing, what are you using to generate G-code? Second are you trying to pull feedrates from the Gcode or using the pendant to set the speeds? Third, after we learn the first two I can give you some feedback.
@@WadeMade The g-code is made in aspire 9.5 and in artcam, I tried both versions, I use the remote control for control, which is set to ignore the g-code, it works according to the advance settings only when idling until the cutter reaches the material, after which it no longer respects the settings, the z axis goes down too quickly and erases the cutter, the movements on the x and y axes are reduced but not on the z axis. Thank you!
I’m looking for information pertaining to adding a 3rd axis or utilizing the extra I/Os on the RichAuto A11E. Can you provide any additional information pertaining to this
I wish I could help but I don't think I have that information. I did stumble across a guide about setting up the a11e on a new machine. If I come across it again I'll let you know
I bought IQ in 2018 and have found your video's to be spot on. I've recently had a problem with my Handheld Controller plagued with the infamous "GREEN" screen. Laguana was of limited help and wants about $1,200 for a new HHC. Looking online I believe I can buy one (new) for around $300. However if I do, I'm not sure Laguana will give me the parameters to set up the new one. Would you be able to provide set up information (parameters, etc) and/or do you have any suggestions for where to look.
I backed up my parameters. I would be happy to share them. As long as all the drives are the same between our models they should work I would think. Let me know if you want them and I'll post a link to the file on here.
Many thanks for your very interesting video. I'm currently having a big problem with my Swift that no one can fix. Sometimes, when the program is started, the speed of advance of the machine does not respect the speeds of the Gcode despite the correct configuration of the DSP. It happens randomly. The speed of the machine is too high and burns the wood. If I restart the program a second time, the machine still does not respect the speed of the Gcode. By restarting the program a third time, without changing any parameters, the machine respects the feed speeds of the Gcode and the cut is correct. Do you have an idea of the problem or a temporary solution for me? Thanks a lot for your help! Julien
I just want to confirm you have the feedrate from gcode setting enabled? Also what program are you using to generate the gcode? If it's a vectric product what post are you using? If you can, post some of your code as well.
@@WadeMade Yes, the feedrate from gcode setting is enabled. I am using Fusion 360 software to generate the Gcode. RUclips must not like the Gcode because it removes messages containing the first lines.
@@tchaotchaokit3463 Hi Julien I've tried to post this response twice now and for some reason, youtube is not allowing it. So the post you used to create the gcode in fusion? Is that a richauto post? It does look very much like that one. There is a Laguna post in fusion you might want to test. It's very different from the rich auto post. I checked your code file and while I can't find anything wrong with it, it's not opening in my ncviewer program correctly. It's missing parts of the geometry. I'm uncertain if this is an issue with the viewer I'm using or your file. I've seen odd things happen to CNC machines when there are rounding errors in the gcode files and that might explain why it's not opening correctly. Lastly please double check your setting in your menu, auto pro, gcode is set to readF and not ignore F. I know I've asked, but that is the only setting that affects this. I was thinking it could be a modality issue but I highly doubt that. I'd suggest a simple program test, maybe a 10" square with a one inch plunge in Z with feedrates of 2540 for x,y and 254 for Z. This will be easy to diagnose if the feedrates are working or not. You might want to test with the post you used above and the laguna post and see if that one fixes your issue. If that doesn't work you might have a defective controller.
Thanks, glad to of helped, I plan to do a follow-up video soon. I was experiencing some issues with the machine losing steps and locking up with Z rapid moves in the up direction. I've since limited them to 100ipm and haven't had any issues but in the next video, I'll cover that, fixture offsets, and a setting in the menus that allows you to set different rapids for the Z, X, and Y.
Hello, I recently bought a used IQ Pro and the controller is not working. It is a RichAuto B57E. Do you know of any resources (like a laguna forum) that can help me troubleshoot? I would appreciate any help!
Does this machine over travel at all in the 24" direction to cut a 24" wide part? They list it as 24" x 36", however they say the bed overtravel's in the Y-Axis by a few inches to route off the end of the machine.
I just checked my machine and from the factory, the max X move is 622.5mm or 24.508". It's possible you could tweak the soft limits to get a little more in the settings but at this width your starting to cover the clamping t-tracks.
I'm pretty sure it's the combo of buttons run/pause and high/low, then pick resume work. I'll take a look when I'm on the machine next time to confirm but I think if you download the axiom manual in my description it's page 26.
I have looked a long time for this information. I am not sure how you located it, but sure glad you did. M controller has something called "FastGrid" in the location you have the term "FallSpeed." Do you know if these are the same thing. Found mine set at 0.5, was wondering if this was limiting my Z plunge rate by 50% of that generated by the Vectric software g-code output? What do you think?
So I tried searching the internet for Richauto and Fastgrid and didn't have any luck. My suggestion would be to test it. You can write a program that plunges 3" with the Z plunge speed at 10ipm in vectric. Make sure to set the tool height higher than 3 inches off the table. If Fastgrid is the same as Fallspeed and you set the Fastgrid to 1 in the control, your speed should read 254mm, then try and set it to .1 And run it, it should then read 25.4mm. If it doesn't change then falldown and Fastgrid must not be the same. What control do you have?
@@robsandstrom9854 Maybe we compare A11E software versions, I'll check and see what mine is tomorrow. If you get a chance, run that test, if it works Fastgrid and fallspeed must be the same. It's odd it would be named differently but maybe it's a different software version. Is your machine a Laguna?
@@WadeMade Not quite sure how to check the software version. Do I plug it into my computer with a USB cord or is it read on the controller. Still trying to have everything you taught sink in. I will also try to find time to run the test you described above. Been a bi busy of late - but I am curious.
Ive had it for a day and i cant see myself every getting used to this control. Is there anyway to mod this to work with mach3 or another pc based controler?
I'm sure you can, anything could be modded. But it might take a little tinkering to get it set up and calibrated. I built a CNC router parts 4'x4' machine using a Gecko G540 and it wasn't so bad to do. But, CNC router parts (AVIDCNC.com now) provided me with most of the settings for that kit. I'm sure there has to be other people that have converted a Laguna IQ. But having used both it's not hard to get used to the control on this. Sure, it's not as nice as having all the information on the screen like Mach 3 but it will get the job done. It's easier to use than you think.
@@WadeMade I've been looking at that same motion controller. I need to do more research on it. I'm hoping the built in drivers can handle my nema 34 motors.
@@chestergt7765 If you are refering to the G540 if I remember right I believe it can handle nema 34 motors but you'll be restricted to the power output of the G540 so you won't get full power. On a machine like this I think you will be fine. You'll lose some potential but for the cost savings you might want to give it a try. I believe I asked Ahren of Avid CNC this same question years ago and I believe that was his answer.
Question. I am often having issues with the hhc not being able to read the usb. It ends up scrubbing it and I have to reformat the drive. Have you had this experience and any solutions? Using the original 8 gig disc that came with it. Thanks.
Good day. may I ask how to setup stepper motor output. I have Oriental Stepper motor and I want to use it in my project using RICHauto A11 can you please help me how to set it up. it is a 2- Pluse mode motor. Thank you..
Hi Sherly, I've never actually set up stepper motors from scratch using this control. In the past, I did come across some documentation regarding this. If I locate it again I'll be sure to post it here. Do you happen to know if your machine has 1-pulse or 2-pulse motors currently?
@@sherlypagcaliwangan4064 ok thanks, we are getting a little out of my comfort zone when we start getting into the specifics of the stepper motors maybe someone that knows more than I will chime in. I could tell you where to set the pulses in the control if that helps.
I'll take a look at the settings once I get back on the machine. You may be limited to the Z-axis length though. But for a temporary fix, you could always try and use a quick change collet like a muscle chuck. That ought to extend your Z lower some. You'll lose some of the Z+ height but if you need it to get a little lower it might do the job?
I don't have any experience with the shapeoko personally but just by looking at a video on it I would think the IQ would be a heavier more rigid machine. The video on the shapeoko I saw mentioned it runs on nema 23 motors. I'm pretty sure Laguna claims the IQ are nema 34. But I wouldn't let the motor size sway you. The Laguna IQ can't really take advantage of the speeds a nema 34 motor can achieve, whether it be the motion design or the controller itself the machine needs to be slowed down from the factory to keep it from missing steps. After that it works perfect and is a solid machine. Stepcraft is another company that makes even a 4'x8' machine that runs on nema 23 motors, albeit with a different motion system. Broinwood has one and makes some amazing wood inlayed cutting boards. But you should know he started his business on a similar machine as the IQ, so that's equally as good. Good luck!!
@@TheHelicapt If your looking to learn on the cheap. I have a romaxx WD-1 I'm selling. 1k for the machine locally pickup only. But you'll still need a mach 3 license, a PC to control it, plus a USB smooth stepper device and a handheld router to mount to it. It's not near as good as what your looking at but it might get you started.
Here is a video of the wd-1 if anyone was interested. ruclips.net/video/5i2pcAiNc14/видео.html the prices at the end of the video have changed. 1k for the machine only.
If your talking about adding on I doubt it's possible. But if your talking replacing the Rich auto control I wouldn't be surprised if it's possible but I can't tell you for certain or not. If it is, I'm betting you'd have to start from scratch with your calibration settings. I've yet to see someone convert to Mach 3. But I wouldn't doubt there are people out there who have.
Thanks for the tip, if I ever get back into using the machine I'll look up this info on my control for you, but if you're not using a Laguna your settings might be different than mine.
@@mrrons7663 It's been a while but I'd guess the Pulse setting will totally be based on the stepper motors, ball screw pitch, and or rack/teeth. Years ago I setup a Mach 3 system and there was a calibration process. I don't know if the A11E has one but I did find you some info on the web. Look up this link and there are some formulas to help you calculate. www.omni-cnc.com/wp-content/uploads/2016/03/A11-Manual.pdf It's for the A11 but I would guess they will be similar. Page 27 and 28.
thanks a lot, you have post two realy interesting videos for DSP users, I have DSP B18 (4axes simultaneous) and I find nothing else als those chinese stuff, ok, what important ist what Wademade post. I have seen tath in Fusion about postprocess there is the Richauto who make a code in .nc (ok with the 3axes), there is also a generic chinese Ledio in .mmg (must take the 4 axes but I have not yet succeeded better than 3 axis with this one and there is te Laguna in .PRG? Laguna propose for the 4 axis to use a other axe, ok sorry you do not have those question, I look forwards, watever if you have something to post about wat make sense to prepare behind the computer specialy for DSP about postprocessor other something else, I will be very interested, have a nice time
Thanks for answer. If you do not, I have allready an other chalenge ;-) is it possible to read the complete name of a file before start it? and an other question (not important) how do you write a welcome message on the DSP? (I have seen one but do not rember wehre)
@@franmo662 I don't think this is exactly what you are looking for, but you can view your gcode on the control. The first line would be the complete name of the file usually depending on what post you are using. But you can find that info here ruclips.net/video/fDrOJ-1CE4g/видео.html As far as a startup welcome message I'd have to look into that. I wouldn't be surprised if there is a way.
I have a Laguna IQ 5 to 6 years old that I bought brand new so far the hand controller has failed twice unrepairable five to $600 for a new one I wish Laguna would offer at least a repair service at a reasonable price machine is great hand controller sucks
Good job! Just bought a cnc with that controller and you are the one that made me understand how to use it! Looking forward for more content.
Thanks so much for this video. You are the first person that has actually covered some of the functions like feed rate from the code.
a whole year looking for such a video totally worth it...Thanks dude!!!!
Glad to have helped. Thanks for the kind comment.
thank you, i've been stuggling trying to get my settings again since I had to reboot all my settings for a computer issue. This explained a lot.
Fantastic video! I spent days trying to get the info in this video from Laguna videos and documentation with no luck. Thank you for putting all this out there!
Finally, a video on setting the tool setter - thanks so much.. Feed n Speed info was gr8 also .. keep these coming!
Dude! I can't tell you how happy I am to find this video! Been operating a couple grizzly machines at work for months and yes going crazy trying to figure out/find info on pulling feed rates from code and using z probe! Manuals have been pretty confusing/useless and most of the videos I've watched are about the same. Thank you so much for this!
Thanks for this video. You have saved a lot of people a lot of time. As you say, it's insane that these good machines some with virtually no documentation so thanks again. BTW, you can control spindle speed dorectoly from your G code. You have 8 possible speed, (S) presets in the handset which you can program to whatever spindle speed you want. Say you want to run a 12000 mm/min, make that, say S2, and specify 12000 in your G code. As long as the handset has that speed allocated to an S number, it will follow the Gcode.. Thanks again.
Do you have a link on how to do this? I can't figure it out.
@@Shipwreck0316 Here you go: ruclips.net/video/yG1QERG4e9I/видео.html
Are you able to change speeds via your pendant, or only via G-code? I haven’t been able to get either to work. I've set G Code Setup > S Read = ReadS, configured the values for Machine Setup > Spindle Setup to allow 8 different speeds, but adjusting the spindle "gear" (as RichAuto calls it) either via the pendant (using ON/OFF + Z+/Z-) or via G-Code (i.e. M03 S12000) still has absolutely no effect on the actual spindle speed. When running the program, the controller correctly detects the speed indicated in the G-code and displays S3 (which is what I have set for 12000 rpm), but the spindle itself reaches 22500 rpm (since I have the VFD set to 375), and the difference is clearly audible.
@@StevenRosburg Hi, I export my code using a 'Richauto' post processor, (from Fusion 360) and provided I've specified matching spindle speeds in the CAM paths, it works.
@@Sentientfx1 okay, thanks. I’m going to have to keep digging then, because I’ve tried G-code that’s generated from Fusion 360 as well as hand-written G-code where the spindle speed matches one of the values configured in the pendant, and while the pendant recognizes the speed by displaying the appropriate spindle setting (e.g. S3), the VFD either never gets the message or ignores it.
Thank you thank you thank you bro I’ve been running rich auto on couple machines I even upgraded one completely it’s an excellent system. I still manage to learn something from you. Cheers, Ziggi from Australia
Great to hear!
Hello, it is the first video that I see of a complete configuration of this control, thanks for the information.
This video was just what I needed! Thank you so much for taking the time to make it! I learned a ton
Thanks, fyi I made a follow up video with a little more info.
thank you so much for this! i have the same machine but different controller- this still helped a ton!
thank you I have had a Laguna swift for 5 years did not know how to use
Occasionally, we find gold. Thank you for pointing this out!
You're the man for this. For real. Thanks
Thanks for this. Illumination!!!
Absolutely amazing video. Thank you so much 👍🏽
Glad you enjoyed it!
Thanks this is the most comprehensive video I have seen. I did change my settings in pro settings like you suggested. Just got my machine. Thanks Again
What is the black knob for on the electrical control box close to the RPM adjustment at the end of the video
Hi, thank you, I have a Richauto A11 and when I click on the file I want to run it loads but immediately then goes to a "line no 1" on screen, when I then press "run" + "1" it does nothing. According to other videos it should start but does nothing. I am very frustrated to the point of wanting to sell my machine.
Ok so lets try and break this down, my first question would be when you click run/pause and the green button on the program does it bring up the set work parameters screen? If it does are you saying after you hit the green go button from the set work parameters screen it does nothing? If so my next question would be, what CAM package are you using to generate your Gcode? Then my next question would be what post processor are you using in that CAM package to generate the Gcode? If your using a vectric product with the correct post then that's a dilemma, I would suggest viewing the Gcode on the machine and checking to see what the first few lines are. My theory is, there might be something in the Gcode that is stopping it from running. Let me know what you encounter and we could try to move on from there. What machine are you using the A11 control system on?
When I press the toolset buttons the cutter moves up instead of down. When I touch the cutter with the touch plate the z axis stops and retracts the set distance.
I have auto updated but that did not resolve the issue. Thanks
thank you keep the good work
Great video man... thanx alot... my machine seems to be ignoring the safe Z height from Vcarve Pro... any idea on how to fix that?
I would start by checking the gcode to see if the Z move to that height is in there. That way you can rule out if it's a post processor or software issue first.
Thanks! It was a very helpful video.
You're welcome, I'm glad I was able to help. I should have a 2ND video up soon with some more info.
@@WadeMade my neighbor has a Laguna Swift 4x4 and I’ve gone over your video with him and he is also very thankful of your videos. I’ve been helping him because I have experience running Haas cnc. We both can’t wait for your next video.
@@miked3612 Thanks Mike, I'm glad I was able to help.
Appreciate the video and all of the advice. I am literally using my Laguna IQ for the first time and I cannot figure out why the puck is not zeroing out Z axis properly. Every time I touch off the puck, the spindle run height is at least an inch or more higher than the work piece. I have abandoned the puck and am just lowering the spindle to the point of touching the work piece and setting Z0 manually. I did go in and tried to set the C.A.D. thickness to the actual puck height of approx 25mm. But that just added even more height to the Z zero when touching off. Any thoughts on how to fix?
I'm sorry to hear your having trouble. I haven't been on my machine in a while but maybe there was a software version change. When you entered the thickness in the C.A.D. thickness on the setting page did you enter a positive or negative number? Whatever you entered I'd try the opposite. But when you go to test it keep an eye on the height so you don't accidentally plunge anything or notice any weird behavior. Maybe hold the puck in the air for the first test. Also make sure you enter the thickness in millimeters. I hope that helps.
@WadeWade Please tell me how to control the fall speed after it starts working because mine it's falling down and working very fast and I don't find the option to set it to fall somehow slower... It breaks my motor and my drill heads. I tried to set "Ignore to all" I set my fall speed to 0.1, the Speed scale to 0.5, the Work speed 1000 and still it's going super fast down while cutting sideways... This sideway cut feels like forced and that's why the machine bends my heads and breaks them. Btw I am using it for marble carving, so it's not a drill bit, it's more for sculpting and creating shapes. Thanks in advance!
First thing, what are you using to generate G-code? Second are you trying to pull feedrates from the Gcode or using the pendant to set the speeds? Third, after we learn the first two I can give you some feedback.
@@WadeMade The g-code is made in aspire 9.5 and in artcam, I tried both versions, I use the remote control for control, which is set to ignore the g-code, it works according to the advance settings only when idling until the cutter reaches the material, after which it no longer respects the settings, the z axis goes down too quickly and erases the cutter, the movements on the x and y axes are reduced but not on the z axis. Thank you!
I’m looking for information pertaining to adding a 3rd axis or utilizing the extra I/Os on the RichAuto A11E. Can you provide any additional information pertaining to this
I wish I could help but I don't think I have that information. I did stumble across a guide about setting up the a11e on a new machine. If I come across it again I'll let you know
Thank you. Wow. Total newbie here. What software program(s) did you use to create the g-code?
I use Vectic Aspire and Fusion 360. Mainly Vectric products though.
I bought IQ in 2018 and have found your video's to be spot on. I've recently had a problem with my Handheld Controller plagued with the infamous "GREEN" screen. Laguana was of limited help and wants about $1,200 for a new HHC. Looking online I believe I can buy one (new) for around $300. However if I do, I'm not sure Laguana will give me the parameters to set up the new one. Would you be able to provide set up information (parameters, etc) and/or do you have any suggestions for where to look.
I backed up my parameters. I would be happy to share them. As long as all the drives are the same between our models they should work I would think. Let me know if you want them and I'll post a link to the file on here.
Many thanks for your very interesting video. I'm currently having a big problem with my Swift that no one can fix. Sometimes, when the program is started, the speed of advance of the machine does not respect the speeds of the Gcode despite the correct configuration of the DSP. It happens randomly. The speed of the machine is too high and burns the wood. If I restart the program a second time, the machine still does not respect the speed of the Gcode. By restarting the program a third time, without changing any parameters, the machine respects the feed speeds of the Gcode and the cut is correct. Do you have an idea of the problem or a temporary solution for me? Thanks a lot for your help! Julien
I just want to confirm you have the feedrate from gcode setting enabled? Also what program are you using to generate the gcode? If it's a vectric product what post are you using? If you can, post some of your code as well.
@@WadeMade Yes, the feedrate from gcode setting is enabled. I am using Fusion 360 software to generate the Gcode. RUclips must not like the Gcode because it removes messages containing the first lines.
@@tchaotchaokit3463 Which post are you using in fusion 360? Can you share a link to the gcode file? Maybe stick it on Google drive and share it.
@@WadeMade drive.google.com/file/d/1fL-KyuqfWqZ4kYsFVHPZm_GPv1PAVLkW/view?usp=sharing
What do you mean by which post?
@@tchaotchaokit3463 Hi Julien I've tried to post this response twice now and for some reason, youtube is not allowing it. So the post you used to create the gcode in fusion? Is that a richauto post? It does look very much like that one. There is a Laguna post in fusion you might want to test. It's very different from the rich auto post. I checked your code file and while I can't find anything wrong with it, it's not opening in my ncviewer program correctly. It's missing parts of the geometry. I'm uncertain if this is an issue with the viewer I'm using or your file. I've seen odd things happen to CNC machines when there are rounding errors in the gcode files and that might explain why it's not opening correctly. Lastly please double check your setting in your menu, auto pro, gcode is set to readF and not ignore F. I know I've asked, but that is the only setting that affects this. I was thinking it could be a modality issue but I highly doubt that. I'd suggest a simple program test, maybe a 10" square with a one inch plunge in Z with feedrates of 2540 for x,y and 254 for Z. This will be easy to diagnose if the feedrates are working or not. You might want to test with the post you used above and the laguna post and see if that one fixes your issue. If that doesn't work you might have a defective controller.
Well done. Thanks a million.
Thanks, glad to of helped, I plan to do a follow-up video soon. I was experiencing some issues with the machine losing steps and locking up with Z rapid moves in the up direction. I've since limited them to 100ipm and haven't had any issues but in the next video, I'll cover that, fixture offsets, and a setting in the menus that allows you to set different rapids for the Z, X, and Y.
Mine doesn’t nearly move that fast when homing. Is this adjustable?
I believe so, next time I'm on the machine I'll look.
Hello, I recently bought a used IQ Pro and the controller is not working. It is a RichAuto B57E. Do you know of any resources (like a laguna forum) that can help me troubleshoot? I would appreciate any help!
I wish I could help but I don't know of any. You you could try vectric or cnczone, but they are not Laguna forums.
@@WadeMade thanks @
Does this machine over travel at all in the 24" direction to cut a 24" wide part? They list it as 24" x 36", however they say the bed overtravel's in the Y-Axis by a few inches to route off the end of the machine.
I just checked my machine and from the factory, the max X move is 622.5mm or 24.508". It's possible you could tweak the soft limits to get a little more in the settings but at this width your starting to cover the clamping t-tracks.
Great video. Can you tell me how to resume a program when you have saved a break.
I'm pretty sure it's the combo of buttons run/pause and high/low, then pick resume work. I'll take a look when I'm on the machine next time to confirm but I think if you download the axiom manual in my description it's page 26.
Not sure if you got your answer. But if not, how you do it is press run and “1” together. Then scroll to break you saved.
I have looked a long time for this information. I am not sure how you located it, but sure glad you did. M controller has something called "FastGrid" in the location you have the term "FallSpeed." Do you know if these are the same thing. Found mine set at 0.5, was wondering if this was limiting my Z plunge rate by 50% of that generated by the Vectric software g-code output? What do you think?
So I tried searching the internet for Richauto and Fastgrid and didn't have any luck. My suggestion would be to test it. You can write a program that plunges 3" with the Z plunge speed at 10ipm in vectric. Make sure to set the tool height higher than 3 inches off the table. If Fastgrid is the same as Fallspeed and you set the Fastgrid to 1 in the control, your speed should read 254mm, then try and set it to .1 And run it, it should then read 25.4mm. If it doesn't change then falldown and Fastgrid must not be the same. What control do you have?
@@WadeMade I have the A11E controller.
@@robsandstrom9854 Maybe we compare A11E software versions, I'll check and see what mine is tomorrow. If you get a chance, run that test, if it works Fastgrid and fallspeed must be the same. It's odd it would be named differently but maybe it's a different software version. Is your machine a Laguna?
My Controller says I have update version q13-1689 and product ID:A0431157 if you wanted to compare.
@@WadeMade Not quite sure how to check the software version. Do I plug it into my computer with a USB cord or is it read on the controller. Still trying to have everything you taught sink in. I will also try to find time to run the test you described above. Been a bi busy of late - but I am curious.
Ive had it for a day and i cant see myself every getting used to this control. Is there anyway to mod this to work with mach3 or another pc based controler?
I'm sure you can, anything could be modded. But it might take a little tinkering to get it set up and calibrated. I built a CNC router parts 4'x4' machine using a Gecko G540 and it wasn't so bad to do. But, CNC router parts (AVIDCNC.com now) provided me with most of the settings for that kit. I'm sure there has to be other people that have converted a Laguna IQ. But having used both it's not hard to get used to the control on this. Sure, it's not as nice as having all the information on the screen like Mach 3 but it will get the job done. It's easier to use than you think.
@@WadeMade I've been looking at that same motion controller. I need to do more research on it. I'm hoping the built in drivers can handle my nema 34 motors.
@@chestergt7765 If you are refering to the G540 if I remember right I believe it can handle nema 34 motors but you'll be restricted to the power output of the G540 so you won't get full power. On a machine like this I think you will be fine. You'll lose some potential but for the cost savings you might want to give it a try. I believe I asked Ahren of Avid CNC this same question years ago and I believe that was his answer.
Question. I am often having issues with the hhc not being able to read the usb. It ends up scrubbing it and I have to reformat the drive. Have you had this experience and any solutions? Using the original 8 gig disc that came with it. Thanks.
Mine won't read 2 of my drives ATM... Can anyone help?
Good day. may I ask how to setup stepper motor output. I have Oriental Stepper motor and I want to use it in my project using RICHauto A11 can you please help me how to set it up. it is a 2- Pluse mode motor. Thank you..
Hi Sherly, I've never actually set up stepper motors from scratch using this control. In the past, I did come across some documentation regarding this. If I locate it again I'll be sure to post it here. Do you happen to know if your machine has 1-pulse or 2-pulse motors currently?
@@WadeMade when I use it in a PLC it is needed to be controled ny 2-pulse modw
@@WadeMade when I use it in 1-pulse
@@sherlypagcaliwangan4064 ok thanks, we are getting a little out of my comfort zone when we start getting into the specifics of the stepper motors maybe someone that knows more than I will chime in. I could tell you where to set the pulses in the control if that helps.
I'm looking for info on how to change the Z limit, I changed to a lower spoil board and a few of my shorter tools won't reach.
I'll take a look at the settings once I get back on the machine. You may be limited to the Z-axis length though. But for a temporary fix, you could always try and use a quick change collet like a muscle chuck. That ought to extend your Z lower some. You'll lose some of the Z+ height but if you need it to get a little lower it might do the job?
@@WadeMade right on thanks
@@WadeMade press menu, table size, increase the Z value
Is this CNC better than the Shapoko HDM ? I’m weighing out both
I don't have any experience with the shapeoko personally but just by looking at a video on it I would think the IQ would be a heavier more rigid machine. The video on the shapeoko I saw mentioned it runs on nema 23 motors. I'm pretty sure Laguna claims the IQ are nema 34. But I wouldn't let the motor size sway you. The Laguna IQ can't really take advantage of the speeds a nema 34 motor can achieve, whether it be the motion design or the controller itself the machine needs to be slowed down from the factory to keep it from missing steps. After that it works perfect and is a solid machine. Stepcraft is another company that makes even a 4'x8' machine that runs on nema 23 motors, albeit with a different motion system. Broinwood has one and makes some amazing wood inlayed cutting boards. But you should know he started his business on a similar machine as the IQ, so that's equally as good. Good luck!!
@@WadeMade
Thanks so much for the insight. A lot to digest and make a decision
@@TheHelicapt If your looking to learn on the cheap. I have a romaxx WD-1 I'm selling. 1k for the machine locally pickup only. But you'll still need a mach 3 license, a PC to control it, plus a USB smooth stepper device and a handheld router to mount to it. It's not near as good as what your looking at but it might get you started.
Here is a video of the wd-1 if anyone was interested. ruclips.net/video/5i2pcAiNc14/видео.html the prices at the end of the video have changed. 1k for the machine only.
Is there a way to change this controller to inches?
I don't think so but I'm not 100% certain on this.
Theres no way to connect a desktop and run mach3 or 4 or any other?
If your talking about adding on I doubt it's possible. But if your talking replacing the Rich auto control I wouldn't be surprised if it's possible but I can't tell you for certain or not. If it is, I'm betting you'd have to start from scratch with your calibration settings. I've yet to see someone convert to Mach 3. But I wouldn't doubt there are people out there who have.
Hi, how do I ask a question here ?
Feel free to ask. I haven't been using my machine for a long while so I'm a little rusty.
you must say about table and pulse Setting
Thanks for the tip, if I ever get back into using the machine I'll look up this info on my control for you, but if you're not using a Laguna your settings might be different than mine.
@@WShep yah i`m not using the laguna,did you know the another machine setting? i`m new user please help me
@@mrrons7663 It's been a while but I'd guess the Pulse setting will totally be based on the stepper motors, ball screw pitch, and or rack/teeth. Years ago I setup a Mach 3 system and there was a calibration process. I don't know if the A11E has one but I did find you some info on the web. Look up this link and there are some formulas to help you calculate. www.omni-cnc.com/wp-content/uploads/2016/03/A11-Manual.pdf It's for the A11 but I would guess they will be similar. Page 27 and 28.
For some reason Laguna ships the IQ with pulses/mm set to 400 for all three axes. It should be 320.
thanks a lot, you have post two realy interesting videos for DSP users,
I have DSP B18 (4axes simultaneous) and I find nothing else als those chinese stuff, ok, what important ist what Wademade post. I have seen tath in Fusion about postprocess there is the Richauto who make a code in .nc (ok with the 3axes), there is also a generic chinese Ledio in .mmg (must take the 4 axes but I have not yet succeeded better than 3 axis with this one and there is te Laguna in .PRG? Laguna propose for the 4 axis to use a other axe, ok sorry you do not have those question, I look forwards, watever if you have something to post about wat make sense to prepare behind the computer specialy for DSP about postprocessor other something else, I will be very interested, have a nice time
Thanks for the kind words. If I decide to get a rotary 4th axis and experience your dilemma I'll be happy to post a follow-up with what I figure out.
Thanks for answer. If you do not, I have allready an other chalenge ;-) is it possible to read the complete name of a file before start it? and an other question (not important) how do you write a welcome message on the DSP? (I have seen one but do not rember wehre)
@@franmo662 I don't think this is exactly what you are looking for, but you can view your gcode on the control. The first line would be the complete name of the file usually depending on what post you are using. But you can find that info here ruclips.net/video/fDrOJ-1CE4g/видео.html As far as a startup welcome message I'd have to look into that. I wouldn't be surprised if there is a way.
Wish I could give you a 1000 likes. Thank you.
I have a Laguna IQ 5 to 6 years old that I bought brand new so far the hand controller has failed twice unrepairable five to $600 for a new one I wish Laguna would offer at least a repair service at a reasonable price machine is great hand controller sucks