How to insert a Tee in pipe without movement - PVC - UPVC - Plumbing
HTML-код
- Опубликовано: 4 сен 2022
- greetings friends
- We are using PVC pipes of the threaded type - heavy class pipe
- Blue glue for PVC pipes
- How to repair PVC pipe
- How to change a PVC elbow
- Repair water leak
- Repair broken pipe
- Repair perforated pipe - Наука
Без движения не получилось, правая труба явно сдвинулась в гильзе в стенке. Нужно было сначала вставить горизонтальные трубы, а затем надеть на вертикальную. Это бы дало большую степень свободы.
И я не понял,зачем он так" сделал. Странное мышление у автора
@@IvanTtofimov это было бы по-русски, а он иностранец, поэтому не смог
Да ,у них мышление такое.Гляньте как пальчиками ,,вставил,, правую трубу. Что-то напоминает.
Если вставлять обе горизонтальные трубы, то сразу вставить вертикальную будет проще.
Ого! Наши забежали! Чё так уже делают? Не паяют? Клей? А сколько атмосфер держит? Старею...
Проще было сделать сначала соединить противоположные трубы, а потом вставить в верхний отвод
Лол, ты разве не видишь что он трубу спокойно подвинул вправо???
Точно ❗хуйней занимается
@@newclient384 он ее согнул фантастическим образом как бумажную...
@@newclient384 Лол, так тебя зовут?
Не совсем понятно, как он последнюю трубу вставлял? Он ее должен был жестко деформировать, тогда вопрос, не возникнет ли в ней трещина в месте перегиба. В общем на таких коротких участках так сгибать трубу очень плохая идея. Тем более трубы будут замоноличены.
Нужно было все три трубы одновременно соединять. Сначала нацепить левую и правую, потом верхнюю. Тогда правую не пришлось бы ломать.
И я про это ☝️
Creo que la solución mas práctica ya la apuntan muchas respuestas y justamente es la que yo también había visto, y es pegar lado izquierdo y derecho y seguido el de arriba antes de secar.
Просто мастер тот ещё еблан
скорее всего он это делал для того, чтобы не нарушался слой клея
тогда бы ты комментарий не написал
There would be less stress on the opposing pipes if you glued all three together at the same time on the upward motion.
I agree and if you noticed on the last joint he slipped the pipe back in the concrete which is not what the thumb nail eluded to
Exactly what I was going to say; no reason not to put both sides in first and then pull down slightly and put on the downward pipe.
The white guy always with the better idea...
Exactly...heat them all up...then put ALL the ends in at the same time...it's the least amount of bending.
Yes - and a lot easier.
@@johnbaldwin2948 yay. The racist has arrived.
Для дренажа пойдёт, для напорного трубопровода это очень рискованно. Труба очень тонкая, после нагрева разрушается кристаллическая решётка, и в этом месте может появится утечка. Хороший мастер соберёт трубопровод сразу, до того как трубу замуруют в бетон, без всякого нагрева. Греют эту трубу только при демонтаже, чтобы сохранить тройник, отвод, или какую либо другую деталь.
У заказчиков планы меняются
Ну, строго говоря, кристаллической решетки у пластиков обычно нету, это аморфные полимеры. В остальном верно, структура их молекул и связей от нагрева может страдать и они могут становиться более хрупкими.
Походу вы на монтаже не работали когда все трубы замурованы в стяжку а лучшие ,, друзья,, сантехника электрики слаботочники начинают свою паутину тянуть а за ими и бравые отделочники ставят перегородки из гипсокартона выбивая пулемётную дробь своими перфораторами и попутно дырявя системы отопления и водоснабжения.
@@russkiyaziat1034 Не скажи , если сделано по технологии стоит отлично. По крайней мере у меня , 25 лет полёт нормальный !!! Правда полипропилен и клей американский. Первый который появился в нашем городе а потом паяльники и европейскийРРR пошёл.
Частичная мобилизация - это когда тебя призывают целиком, а возвращают по частям
The proper way to do this (if doing this method) is to heat both bottom lines, bend them down, connect them, then push up to secure the upper line.
This should be called "what not to do".
I've noticed others have stated the same thing after I commented.
Agree and I did the same lol
Correct
When you do it your way you have to pull bottom pipe back first to clear the tee to end of top pipe. This causes the bottom pipes to pull out and if they dont pop out it's still not good to introduce air pockets into the solvent weld as you push pipes back in. With fast setting solvent doesn't go so well. Instead of heating pipe I would, instead, cut the stop out of a short coupling. Use it as a slidable device after connecting one bottom pipe to top pipe.
You are absolutely correct sir
But you have to be fast, and you have to push up before the two sides setup;
because you might need to rotate both sides in order to mate with the top.
If the two sides have setup, but the top does not mate, then you'll be in trouble.
Perhaps there's a slow setting solvent that can be used.
Muy buena técnica de limpiar y limar la tubería x adentro y x afuera. Es muy importante k muchos olvidan 👍
А слабо в нижнем положении тройника вставить сразу слева и справа, а затем и надвинуть на вертикальную трубу. Меньше тело движений.
Слабо, не умно, российское : авось пронесло
Мы не ищем лёгких путей)
Ловкость рук и ни какого мошейничества...труба справа спокойно подвинулась сколько надо было....тут без накидной гайки и муфты с наружной резьбой не обойтись так будет правильно
Она не подвинулась, а согнулась.
И рукой прикрыл..
@@asumptio с таким перегибом она б уже не разогнулась.
А в чем проблема сначала параллельные трубы соединить, а потом перпендикулярно? Тройник подвижен ведь.
@@asumptio Этого мы не видели: согнулась или продвинулась. Но если бы ТАК согнулась, ... Это больше похоже на "переломилась" Дурят нас.
сначала две горизонтальные соединить а потом уже верхнюю,так было бы проще!
Для этого есть специальная пара: штуцер и накидная гайка. Специально для таких ситуаций
@@old_falc вы считаете правильным хоронить в стяжке резьбовое соединение??
@@Dmitry_Storozhenko Ну да. А склейку, тем более произведённую таким способом, правильнее?. Да и не думаю, что это соединение будет замуровано насмерть: закроют лючком, возможно скрытым. Мне вообще не нравятся всякие попытки натягивания на говне шкурки... конкретно - технология показанная в сюжете.
@@old_falc ну, лючки в стяжке вряд ли кто-то делает, если это стяжка. Да и вообще, склейка - лично для меня - дело сомнительное. Я отдам предпочтение пайке. Гораздо надёжнее, на мой взгляд. Никакой резьбы и склейки.
@@Dmitry_Storozhenko в Европе водопроводные трубы склеиваются при чем склейка гораздо лучше пайки... резьбовые соединения и я не стал бы делать в стяжку...
La idea es real y efectiva el tubo de la derecha dobla pór el calór que lo ablanda, la esponjá contiené águá para controlar ĺa curva y poder trabajar, luego lo calíentas ý lo metes en la te.....la humildad al recibir un contenido es muy util, no te fijes en errores de edicion, gracias amigo.
Вариантов масса! Каждый делает как может. Данный вариант называется,- когда коту делать не хрен,- он яйца лижет😁
Да... и главное - правильно выбрать яйца.. чтобы неловко не получилось.
No. The fittings need 1/4 turn to distribute the cement to the joint properly. Do the following:
-Dig the trench longer so the pipe can flex naturally without heating.
-Cut the pipes as shown (buy a cutter and a deburing tool if you make a lot of these repairs)
-Cut an arbitrary length from the T pipe. Make sure it's longer that 2× the depth of the fitting sockets. 15cm is more than long enough.
glue the pipe into the T socket. Following the instructions on the glue can for twisting and hold time.
-Take the newly made T assembled and glue it into the straight section of pipe, aligning the T pipes, again following the glue manufacturer's instructions.
-Use a coupling to join the T pipe, again following the gluing instructions. If you've dug the trenches long enough the pipe will flex enough to fit the coupling in easily.
And that's how you add a tee to a straight run of pipe without seriously weakening the pipe itself.
For proper gluing the joint shouldn't contact water for 30 minutes to 24 hours depending on the pressure to be run. If a small trickle of water cannot be controlled by closing a valve some slices of white bread can be uses to block the pipe. Get the cheapest bread possible. Wad the bread into a ball and shove it several inches/cm into the pipe. When water pressure is restored the bread will dissolve in the water. Seriously it just basically disappears.
You seem knowledgeable with this much verbiage. Blue glue is hot set glue and cures in a few minutes.
He doesn't know what he's talking about.
Doing what he said is totally unnecessary and a waste of time and money.
There is one thing I always do, no matter what clue I use.
And that is using a primer.
I've done thousands of these type of connections.
And almost every time that I used a clue that stated that you don't need to use a primer.
The connections failed within a few weeks.
Plus with a primer you will get a chemical bond.
And a physical bond.
2 thoughts. 1) The pipe appears to be polybutylene.and that would not work on pvc nor cpvc. 2) I don't think it actually worked here. The last glue up was obscured by his hand, and the pipe either bent into an impossible U shape, or it moved horizontally.
Watch again and see if you see it.
This is the way
@@keithmarlowe5569 - I concur, perhaps the setup is a fake since the camera does not show more than a few square feet. The pipe did slip to the right most likely from the bending pressure and if this was a real long pipe embedded into a real all it would not do that. The hand obscuring the pipe is a red flag too. If someone wanted to teach someone how the difficult part was done right they would hide the pipe behind their hand.
I would have done the two sides since they were already bent outwards, and then pushed it up on to the top leg.
Hola maestro buen día siempre Gracias Santiago 🇨🇱
Buen video, explicas muy bien este método, yo lo he hecho sin calentar los tubos, pero de cualquier manera hay que aprender todo posible método, gracias por compartir tus conocimientos
Y como se logra sin calentar los tubos. Yo tengo una situación donde quiero poner una t en cpvc blue
из раздела: когда коту заняться нечем, он яйца Лижит 🤪
Buen video, la conexión correcta se hizo debido al resorteo del tubo derecho previamente suavizado con la pistola caliente.
Genius. Love this technique. You are like Sigfried and Roy but in one person.
Exelente con el calor se puede manejar la tubería fácilmente buen video. ..
si, pero lo debilita,,, pierde mucho.
Nooo el pvc después vuelve a su estado normal yo lo e usado Muchas veces y me sorprende lo bien que queda muy garantizado
ruclips.net/video/IxZxjOzoN3Q/видео.html
ппц... если трубы довольно быстро прогреваются, то надо было сначала добавить клей, потом прогреть левую и правую, одеть на них, потом на центральную... всё в один заход... чтобы не "ломать" правую.
Gracias por tu aporte y tiempo excelente trabajo yo trabajo en plomería de albercas por cerca de veinte años y no tiene truco tu video es real yo lo he hecho varias veces cuando se rompe una tubería y tienes que acoplar solo calentando el pvc es la única opción . gracias por compartir tus conocimientos 👍
Disculpa. pero no es la única manera yo también los arreglo con un cople solo le quitas la separación que se tiene en medio y listo
ruclips.net/video/IxZxjOzoN3Q/видео.html
No existe otra forma
Excelente explicación...Gracias.🙏👍
Muy buena la técnica para insertar la tele ahora ya la aprendí muchas gracias Dios te bendiga saludo de Perú city .....
Era la tee de tubería de media pulgada
Wrong order, should connect both bottom lines then the top would be much easier
yep
The last pipe must have been very flexible or was pushed back!!
The later, that's why he hides that end with that fabric in his hand.
He fully kinked it, not how i would approach this type of repair here… but pvc water pipes are not used at all now, with mdpe fittings you can do fusion welding, theres also slip couplings for pvc which i have used in the past. Can get quite hard in confined spaces especially with concrete.
I think it creased
ruclips.net/video/IxZxjOzoN3Q/видео.html
Ну где бы вы столько коментов написали -он не слесарь -он блогер😂
я бы склеил сначала горизонтальные(по картинке) трубы, потом вертикальную. склеенная горизонтальная труба шевелилась с большим запасом из-за получившейся длины, тогда можно вклеить вертикальную без случайного перегиба.
Думаю, он так делал не просто так. Твоим способом нарушился бы слой клея, то есть его бы больше вышло из швов из-за боковой нагрузки.
@@VictorGravit , а перегнуть трубку как? проще? я не буду говорить о том что она была нагрета и стала мягче, но кто знает что в месте перегиба будет после остывания? микротрещины там или еще что... у меня нет таких материалов для эксперимента, но я все равно использовал бы свой метод))
ruclips.net/video/IxZxjOzoN3Q/видео.html
Надо сначала горизонт вставлять потом в вертикаль.
@@user-uh3sh3uj6z одаренные сначала паралель потом пенпедикуляр.
ruclips.net/video/IxZxjOzoN3Q/видео.html
Мне интересны обстоятельства, при которых трубы без соединения оказались в исходном положении.
Китайцы.
Сначала создают трудности, затем их преодолевают.
Джамшут трубы прокладывал, а Равшан бетон ложил :)
Genial! Thanks from Brazil 🇧🇷
Si es cierto.yo use esa tecnica para un tubo pvc de 100mm...y resultado es mismo..😃
Здесь нет ни горизонта ни вертикали, это всё в полу (посмотри на капли они капают вниз ) а правая труба действительно хитрая , она двигается.
Он её заломал
Она не двигается, фен ее сделал гибкой
100%)
ruclips.net/video/IxZxjOzoN3Q/видео.html
Лажа полная в конце видно было что трубка отодвинул ась в право а вот бывают в основном случаи что ничего не отодвинуть тогда нужно сразу все концы отогнать и все соединить сразу
Он ее согнул, а не отодвинул.
Neat way to do it if you don't have compression coupling. Thanks for sharing
Excelente video cuando todos
Me gustaría saber y ver más videos acerca de trabajos con tubo de cobre
Aunque es una solución antitecnica. Admiro como logra hacerlo con tanta habilidad. No es fácil resolver esa configuración. Saludos
Claro que sí es fácil con un cople y quitas la separación que tiene en medio cortas un o de los tubos y el cople lo colocas de forma corrediza y unes el tubo que cortaste y listo
Ahora con uno de cobre porfavor 😃 excelente video
Con los de cobre limas el pare de un lado de la pieza para que se deslize pasa el medio o centro de la pipa y despues la deslizas hacia la otra pipa al mismo tiempo que unes la pipa vertical. Hay un video de alguien que lo ensena por ahi.
@@Esuper1 muchas gracias por la información 👍☺️
ruclips.net/video/IxZxjOzoN3Q/видео.html
This is a great lesson on how to not work with pipe in tight places by someone who doesn't know what they are doing...
Абра-кадабра, сим-саламин, сыла в волшебство однако
2:35 that pipe clearly moved
it did, kinked the pipe = fail. he did it wrong anyway. i could do it without heating the pipes.
@@jesvans how?
@@zaxarispetixos8728 side it on the left pipe, then the right pipe, then the top pipe. it will go.
ruclips.net/video/IxZxjOzoN3Q/видео.html
Excelente conteúdo!
Muito obrigado por compartilhar.
좋은 기술을 배웠습니다.
감사합니다.
I learned a good technique.
thank you
I like the way you covered the pipe with your hand so you couldn't see the kink you made in the pipe.
When he connected the last pipe did you😅 notice the pipe slid to the right then back into place. This idea may work but this demo was bogus.
I don’t believe everyone it slid at all. I believe he linked it the had to straighten out the link. Look where the pipe enters the masonry. The masonry is tight against the pipe before and after.
It also has to be hot as hell for it to stay so pliable for so long, and yet he calmly held on to it bare handed for forever 😲
heat the 2 conduits that are in a straight line , bend them out slightly , glue the 2 ends of the straight conduits and slip the coupling/ tee joint on both making sure that the tee will align with the other conduit. heat up the conduits until they are flexible ,glue the 3rd conduit and then press the tee onto the glued conduit
Good job very nice job very nice thing very nice enjoying a very nice tools very nice finishing
A very high standard of plumbing work. Most just couldn't care less.
You should always apply primer on PVC before applying cement - especially for PVC water pipes.
Depends on the glue. Some doesn’t require primer
Sanding eliminates the need for primer.
ruclips.net/video/IxZxjOzoN3Q/видео.html
Мне аж глазам больно стало, когда он правую трубку заломил. Ведь напрашивалось же решение вставить две боковых, а затем одну верхнюю. Или для этого и задумка, чтобы комментариев больше было? :-)
Show muito bom 👍🏾👏🏾👏🏾👏🏾👏🏾🇧🇷
Отличный пример. Про клей ПВХ впервые слышу, спасибо в будущем пригодится. Совсем недавно приходилось искать (пи@дить) трубы, искать сварщика, да и сварочные аппараты работали так что все электроприборы на нашей улице моргали как новогодняя ёлка
Doesn't heating the pipe to a temp that allows you to bend it like that cause it to loose its strength / pressure rating?
you may be right from a technical perspective.
but for typical household pump pressure the cooled and hardened pipe still has the reliability we need.
plus for years people have been heating and fitting pvc so its also a time proven method if you're in a bind. which I think is the point of the video.
No, it does not harm it. But you do risk kinking the pipe.
As others pointed out, as i too noticed, it would have been easier to first insert the two on the left and then shifting everything back up to the upper pipe. But since the person clearly moved the one on our right to make it insert they failed to live up to the title of the video by not moving anything.
I thought I observed the same thing
Here's my take - A slip coupling is your best friend in this situation. No heat gun required and you can take your time with 2 part glue and primer and bevel your pipes properly. But hey what do I know, I'm just a master plumber.
Excelente! 👌👏👏
I, for a time, helped to run eight PVC extruders. They made PVC things. We had a safety protocol to empty the machines of molten PVC during a " Black out". It actually happened once after a 5.0 earthquake. ( So. Cal). PVC, PolyvinylCloride, gives off a gas, that looks like smoke. It's called Tetra- hydrochloride. One "wiff" could collapse your lungs. Just a little FYI.
If the T had the same diameter as the pipe, one could slide sockets over the joints instead.
But even with this thicker T you could glue pieces of pipe in the T first, and then use sockets.
That would not help, but, I'm sure he moved the last pipe, watch it again
Nice job thanks for the video ❤
Thank you, great video
Muito bom! Se encaixasse os dois de baixo primeiro seria perfeito
Pensei o mesmo kkkkkkk
Até porque, dar-se impressão que o cano da direita está falso ( ele o empurra para dentro para ter o espaço...e o que eu vejo)...
Правая труба двигается на ней не видно ни заломов ни згибов туфта.
Ah.... now I know what to do if I ever see 3 pipes trapped in a little hole! 🤣
Excelente aporte............
Interesante ese metodo, pero el calentar y doblar la tuberia ¿no la debilita en caso de que los liquidos que van a pasar esten calientes?
Lo calienta para que pensemos que es la manera pero en realidad el caño está suelto. Un engaño!
Muy bien maestro
Y si fuera tubo de pared delgada como se hace?
Saludos, necesariamente tendria que cortar las tuberias y usar Uniones o talvez ejecutar bocas a las tuberias ....
Brilliant! Excellent video.
Главный секрет успеха это жёлтая, тряпочка!
It would of been easier bending horizontal pipework down then connecting tee,heat pipe up again then pushed it up onto branch pipework.
Parece interesante 🤔.........
Lo será
В начале 2000-х американка была и такой же клей и клеили, прошло 22 года, все ещё так клюют!)))
а что за клей это?
If people worked this slow. We’d still be in the stone age.
Что за клей?Какое давление выдерживает? Я в хозтоварах не видел.
Это термогидробарический суспензионный универсальный наноклей пролонгированного действия.....я тоже такой нигде не видел,потому.что я его только что придумал)
Al poner el tubo del lado derecho se ve claramente como se desliza para atrás y logra insertarlo a la T, entonces si todo fuera estado de concreto y nada se movería, no podría insertarse, tanto por ser un espacio muy reducido. Es un video mal hecho.
Como Usted diga, le agradezco el comentario. Nosotros estamos seguros del video que mostramos......Éxitos a Usted ...(Este trabajo es tan fácil que no existe la necesidad de hacer trampa)
Ele enganou todos. Nao e assim que se faz.
Oswaldo Arellano te equivocas. El movimiento brusco que viste es porque por un momento la tubería se chupó pero la mano no permitió que se viera eso. Ya cuando insertó el tubo en la conexión el tubo recuperó su forma. Soy fontanero y a mí me ha pasado cuando hago esa maniobra. Quiero hacer hincapié en que -si defiendo este video- no es que yo tenga algo que ver con este canal y no conozco a la persona que hizo este vídeo pero sí puedo dar fe de que la maniobra es posible y reconozco ese movimiento brusco que percibiste y que malinterpretaste como un deslizamiento del tubo dentro del muro. Entiendo que no has tenido esa experiencia y por eso percibiste mal. Pero no pasa nada. Me es un placer aclarar el tema. Saludos
El tubo está caliente y de vuelve flexible, se tiene que trabajar rápido para que no quede deformación en el tubo.
@@kasu7639 exacto
Son trabajitos claves que a veces te desesperan.....
Профессионал 😂 на деле все трубы деформированы и лопнуты
Be easier to use a slip fitting.
Infelizmente o tubo não ficar este tempo todo flexível por causa do calor, ele deveria ter colocado os dois tubos da horizontal e depois o da vertical
Totalmente de acuerdo
Good job! Congratulations! Initially I thought to be very difficult, but on final was simply. Thanks!
Fabuloso gracias
20mmとなっていますが、1/2インチと書いてあるので、13mmじゃないですか・・・
Yo lo hice con soplete, quedó un poco deforme y quemado pero si se pudo 😁
Las primeras veces nos sale así, incluso muchas veces fallamos en el primer intento,,, es cuestión de poder practicar...gracias por comentar
Nicely done!
No sé que tanto se quejan. Mal no lo hizo. Consiguió resolver el problema.
Eu faria diferente, colocaria os dois tubos na horizontal e depois colocaria na vertical.
Yo también, sería más fácil
Чудным образом труба справа ушла в стену и вернулась обратно...тогда зачем весь гемор с прогдевами и чудной смазкой?
это не чудосмазка это клей...
@@Viktor_Pertsovich даже не сомневаюсь..и потому как трубы от температуры теряются в размерах,использую резиновые прокладки по старинке(ну кто-то премию получил за изобретение)
@@AlexAlex-wf3mt резиновые прокладки только в канализации хороши, а на горячей воде резина не долговечна
Increíble que suban este video tramposo!! El caño de la última unión lo muestran como fijo en pared pero en realidad está suelto.
A las tuberías no se les echa tanto pégamento que dentro de la tubería se produce una rebaba y reduce la velocidad del agua y en tuberías grandes que llevan cosas pueden producir atascos
Saludos , gracias por los consejos . Exitos a Usted .
Use primer. Then, wipe off excess solvent "bead" with a rag or primer dobber as the solvent continues to eat into the pipe until it cures.
Muchas gracias por el video , cierta vez me toco hacerlo y creo que lo hice mal , en mi pais solo existe el pegamento transparente y naranja ....que es ese pegamento azul ?
Espero le ayude el video
Hi_vp,hi_3p,pvc 계열은 열을 가하면 하자가 발생삽니다
Pegamento para pvc OATEY azul u otras marcas en Peru
Структура трубы при нагреве и загибах изменилась.Под давление такой узел нельзя ставить.На самотек пойдет.
Фокусник, артист!
배관에 기초 지식이 없는 사람이 배관 하네요 이런 댓글 남기는것도 시간 낭비 하는듯 한데 잘못 된 지식을 올바른 방법을로 인식 할까봐 남겨요
우리는 서로 다른 건설 시스템이 있다는 것을 이해해야 하며, 다른 작업 기준과 무엇보다도 다른 자재가 있음을 이해해야 합니다. 인사말 .
Пиздеж! Труба справа спокойно перемещается на этом видео!
Всё трубки вставлять одновременно. Так мне кажется лучше.
Нужно вставлять все три сразу с нагревом правой и левой труб. Но если честно то такого способа соединения на холодную я не знал. Какие-то специальные трубы и соединения.
En una epoca todos los pegantes eran transparentes, una marca de pvc uso el azul para reconocer sus productos y asi responder por la garantia.....
Eso depende de q pais seas seas en mi pais el pegamento de cpvc es amarillo y el tubo es color hueso no gris
Aqui no Brasil não tem esse tipo de cano. Parece um tudo flexível.
Ahh, this reminds me of when I used to lay piping on my property; those were the days!
Perfeito a ideia!
Não acredita em tudo que vc vê no RUclips não. Porque vc pode se descepcionar.
Repara no último momento do cano. Para onde ele recusou aquela tanto? E cano PVC não inverga com tanta facilidade assim não. só acredito vendo pessoalmente