Ecovacs Deebot 950 bumper malfunction || diagnosis, repair
HTML-код
- Опубликовано: 31 авг 2023
- This video focuses on the Deebot 950 and demonstrates a potential solution for repairing the right bumper sensor when it malfunctions.
*Disclaimer*
This video is for informational purposes only and demonstrates a repair on a circuit board. Please consider the following points:
1. *Personal Responsibility:* The execution of the repair shown in this video is done at your own risk. Any damages that occur during or after the repair are the responsibility of the user.
2. *Loss of Warranty:* Repairing the device as shown in this video may result in the voiding of the manufacturer's warranty. Please check your device manufacturer's warranty terms before proceeding with the repair.
3. *Expertise:* It is strongly recommended to have adequate knowledge and skills in the field of electronics and repairs before attempting the steps shown in this video. Lack of experience can lead to damage to the device or personal injury.
4. *Safety:* Follow all necessary safety precautions, including disconnecting the device from the power source, before starting the repair.
By watching and following this repair video, you agree to the above conditions and accept responsibility for any consequences. The creator of this video assumes no liability for damages or losses resulting from the use of this video.
Credits: Liquid_Ref from www.roboter-forum.com
Music: Magnetic Trailer - Eccentric Funny Music, Lesfm - Real Estate Corporate 
Наука
This video should be more popular: it solved my bumber error. Instead of giving attention to so-called "influencers", videos such as this one should be much more respected and pushed because this makes a REAL value to the world: reduce e-waste by reparing.
It worked for me. Vielen Dank !!!! GREAT! THANK YOU !!
Super! Vielen Dank für dieses Video! Hat meinem ozmo das Leben gerettet... 😂 Auch ich konnte einen aus der Kiste verwenden. 1/4 W Metallschicht
Спасибо! На моем приборе точно также сгоревшие резисторы! Человек, ты лучший! Я месяц пытался сам найти неисправность!
superbe video , faudrait avoir un lien pour acheter la résistance Milles merci 👍👏👏👏👏, j ai trouver la resistance vendue par 100 = 5 euros pas facile a soudé , on y arrive quand meme 20 mn pour la reparation au total , fonctionne nickel merci
Thank you so much for the video. Would u happen to know how to fix it when the robot keeps going against the wall all the time?
Thanks man! I was about to throw my deebot away. I used a regular resistor (330 ohms .25 watts) and it worked just fine.
You are welcome. Good to know that it also works with regular resistors. Did you encounter any challenges when soldering the "large" connectors of a regular resistor onto the board?
thanks for the guide...
you are welcome :)
oh man! Thank you for your video and information! I was loosing a lot of time to find what was the root cause. Maybe you can add some words to the description so , maybe, googling can link easier to your video. I was looking for "deebot 950" + "no straight line" , "near wall", "no straight trajectory", "rototraslation" , "bumper sensor not working". Do you know or think if this issue could be also the casue of going backwards when plugging the water tank?
Hallo,
thank you for your feedback. I'll be adding some of the suggested tags.
Unfortunately, I can't confirm if the issue you mentioned is connected to the malfunction.
Maybe you can report if the behavior has changed after the repair?
@@LukasWorkshop-rv3fc I tried first attempt with official support for the SMD, but they are trained to give pre-defined answers and pre-defined options (ship it, check it, estimate the reparation without any reducition and ship it back). About behavior with water tank I whink it's a problem of mat sensor. I tried to clean it before discovering your video. Now the robots sees mat everywhere, so the backward direction could be for this reason. Wehn I will make all the reparation I will let you know. Thank yuo again!
Thanks for the Video.
At my Deebot both resistors were defect. Looks like a design flaw.
Material cost was a total of 1,94€ as I had to buy 100 pcs. So I have spare for the next century.
How did you find out what parts are broken?
Thanks again Mac.
Hi, glad I could help you with this video.
I got help from a german forum called roboter-forum.com. Looks like a lot of people have this problem, so I also think it is a design flaw.
Best Regards Lukas
Hey
Habe. Sie eventuelle einen Link zu den zuverwendenen Widerständen?
Wäre ihnen für die Hilfe sehr dankbar.
Und vielen Dank für das top Video
Hallo, habe die hier genommen: modellbau-schoenwitz.de/de/Elektronikbauteile/Widerstaende/SMD-0603/SMD-Dickschicht-Widerstaende-330-Ohm-1-0603, Mindestabnahme sind zwar 20 Stück, war aber das günstigste was ich so gefunden habe...
Dann viel Erfolg bei der Reparatur :)
Bei mir waren tatsächlich beide Widerstände defekt, ich habe dort "normale" 330 ohm Widerstände rein gelötet, jetzt funktioniert es wieder. Mit normale meine ich, keine SMD sondern einfache Widerstände aus dem elegoo Baukasten.
Vielen Dank für das Video, ohne dieses wäre ich nie da drauf gekommen.
on my robot both resistors deliver no voltage ._.
Yes, sometimes it is also possible, that both resistors are broken... Did you manage to fix it?
@@LukasWorkshop-rv3fcNo, I can‘t do that on my own, just measured the values
Me2 no way I can do this on my own 🙃
Thank you so much for the video. Would u happen to know how to fix it when the robot keeps going against the wall all the time?