How short after replacement did u get it...if you read the comments some people will turn it on and wait and it goes away ...or run it for a little and cut the power for 20 min after it was running...if you find the heater wires I've seen regular heaters at 22 ohm or 33 ohm these I am not sure I feel like any ohm reading that's not infinite should be good
@@fixitfelix718 I'm almost 24 hours after replacement/reset. I see the other comments and will allow for a few more cycles before pulling the trigger on the heater.. just wanted to be ready. Thanks for your continued support!
Thanks for that i appreciate it!!! If you ever need help with appliances seriously reach out! My contact info is in the first few videos! I try to help everyone!
@felix i made a small dent on the inside of the freezer with the screw driver - is this going to cause a major issue i covered with with black gorilla duck tape - it is a small dent - i am very worried - its like a small hole
@@fixitfelix718 bro felix you are the man thank you - i used some food safe dap all purpose silicone to fill the dent - i shouldn't have tried to break the ice with the screw driver - i defrosted - and waiting for it to cure before turning it on i hope the e4 goes away - i haven't tried changing the sensors yet -Blomberg BRFB1051FFBIN thats my fridge what are the parts i need to buy from encompass in case e4 doesn't go away?
Hi. So i DONT have the error, but i do have the ice build up at the bottom. I believe there may also be a build up at the back of that panel because it looks bloated like a belly. Any advice?
Hi Felix, I replaced the two sensors as per your video. Thanks 🙏 i do not see an error code and I opened the back cover after three days to inspect and don't see any ice build up but do see some frozen drops on some of the pipes. Is that normal?
@fixitfelix718 I just left it unplugged for a day. I will check again in a couple of days to ensure no new build ups.... I have a picture of the frozen droplets, can I send it to you for your opinion?
Defrost sensor and evap senor..if i were you, just because encompass parts..thier #1 parts seller sucks..,,, i would call them and then read off the numbers on the sticker on the side of the refrigerator section..usually starts with brfb#### ...ask for all 3 or 4 sensor in freezer and match them up to the ones in the video...or in that general area..then return or keep the other...its about 5$ each... encompass. Com i believe or parts town. Com. Let me know if that helps
@@fixitfelix718 thanks for your response. I found the model number there! My issue is When I open the fridge I get a flashing error on the display panel it shows 40 (f) : 10 (d) then flashes to E : 4. With the red triangle & exclamation mark ❕🔺 and was beeping. I managed to turn off the alarm by holding the alarm button. Defrosted my freezer fully and I tried to take the small clip off that you showed had a zap strap in your video and one side of the clip snapped but managed to get it to still sit on snug. I am just going to leave and see if it eventually goes away. I red online it can go away. If it doesn’t in a couple days I will try to again and order the parts from the site you suggested. How long does it take to arrive? I find it a pretty tight area to work in pulling the cords around the sharp areas and I don’t want the pipes to open up like you mentioned in the video. Mine is a built in fridge. Really appreciate your response Felix!
hi! im getting charged ~ 150 for FRZ DRAIN HEATER and ~ 150 for Blomberg Sensor. the blomberg fridge/freezer model is is K56300nebu.Not sure if the parts are specific and different for each model. just curious if im getting ripped off and where i can find parts for cheaper? thank you felix!
Hi, In my case, shown E4 code, iced in evaporator. replaced evaporator and temperature sensors, the heater core R= 125 oum. same problem. what should I do next? Is there a control board that could be defective? Can find schematic for this freezer? Thanks.
From what I see the heater looks good and e4 should dissapear after a couple cycles .there was a way to tap in diagnostic mode but I lost the site..email me I'll try to find it...Nd you can flash the board....indont think with good heater and new sensor it will ice up again...if it does its the board....schematics are hard to find for this...I used another models info once and guess how to get into diagnostic..I'll try to send u it..just let it run for a couple days....other comments had the same issue and it dissapeared...
@EmpowermentMentality turn up temp or hold one of the buttons for 3 seconds...on the screen you'll see a " /"0" hold it for 3 seconds...or find the circuit breaker and turn it off over night
Hi Felix, when I powered the fridge back on the freezer fan wouldn’t spin. Nothing seems to be blocking it. Before defrosting the fridge the fan was working. Any idea what it could be ? Or does it take a few minutes for the fan to kick in ?
Hello Felix - I swapped the two sensor cables with the new ones today. Turned off fridge, turned off power supply to the fridge from the switch board. Turned back on. The error is still there - Pls Help!!!
So I recommend either leave it alone like this 3 days it will dissapear after a couple cycles...or whiel the refrigerator is running after 24 hrs...hit the breaker off....leave it off for 1 hour and then turn it on again.....younhad e4?
Hello Felix, my blomberg fridge had the same error. I ordered the two parts and replaced them, but the e4 error still appears after rebooting. 😢what would you advice the next step to be?
Did you just reboot it .. i recommend shut off the refrigerator first..hit breaker for 15 min..then breaker on ..then turn on....make sure both connectors were pluged in good and firmly...it will probably go back to. Normal by tomorrow if not let me know
Hi, I dont know how to setup my fridge. Every mode seems to be to cold, and the vegetables are freezing. Am I suppose to put the fridge at 46, 43, 40 or 37??
@alexandregagne1209 yea I believe you but my question is important...you might be missing the fan motor magnet at tip of door so everything freezing because when you close door fan doesn't run
Not sure... e1 I think it's power fail but I have 2 numbers for tech support 8883522356..8004599848.... you can try this the 888 is for technicians I believe...just pretend you are and try to get the answers .....I looked for my cheat sheet on errors but I can't find it...
Thanks! Fixed, except it wont reset the error code. Holding power button turns it off and on, with error code returning immediately. Unplugging doesn't work
Yes, I cut the power from breaker while fridge was ON and I didn't restore it for several hours (maybe 5?) and it did reset. Purrs like an error free kitten now (after your fix, thanks).
Not easy you need to.find the service manual I lost it and even with manual I'm not sure...I think when you turn it on and off it starts in defrost sometimes. Usually I replace sensors after a manual defrost and in a few days it refreshes the code
@@pavelmedvedev358 probably the heater is OK usually sensor fails and back when I made the video I couldn't figure out which was which so I just always do both on top.
@@pavelmedvedev358 the resistance depends on the temp of the sensor and I don't know the parameters of those thermistor but in a warm cup and an ice cup you can measure the ohm but i dont have clue what temp equals which ohm...could be out of range when in the extreme temps. No idea
Anyone know how to test the defrost heater (ohm reading)? Replaced both sensors and still getting an E4 error. Thanks
How short after replacement did u get it...if you read the comments some people will turn it on and wait and it goes away ...or run it for a little and cut the power for 20 min after it was running...if you find the heater wires I've seen regular heaters at 22 ohm or 33 ohm these I am not sure I feel like any ohm reading that's not infinite should be good
Google "skillcat team heater ohm reading " I just like 22 to 130 or something like that try that page veryyyy similar to your refrigerator's heater
Refrigerator Troubleshooting: Defrost System - SkillCat www.skillcatapp.com/amp/refrigerator-troubleshooting-defrost-system
Did you see the site I sent
@@fixitfelix718 I'm almost 24 hours after replacement/reset. I see the other comments and will allow for a few more cycles before pulling the trigger on the heater.. just wanted to be ready. Thanks for your continued support!
Felix is a great repair man and walked me through the steps over the phone.
Luis sent me here. Subbed.
Thanks for that i appreciate it!!! If you ever need help with appliances seriously reach out! My contact info is in the first few videos! I try to help everyone!
@@fixitfelix718 Sure! Any friend of Louis is a friend of mine!
Solid content as always!!
Hello, can you please provide a link to get these products : Defrost sensor/ E vape sensor for this Blomberg Refrigerator. Thank you
Great video, thank you!
Thanks please like and subscribe to help this reach more people.....we're you able to fix it?
Great video i just have to find time to change them.What the name of the website to order the parts?
Encompass. Com or search Encompass parts ..if you have trouble email me the model sticker ..I'll try to figure it out
Is there a way to keep the main refrigerator on while the freezer if off as it’s defrosting?
Thank you!! This is great help, Sr!!
Louis sent us here
Hes an awesome dude...i gotta say!
@felix i made a small dent on the inside of the freezer with the screw driver - is this going to cause a major issue i covered with with black gorilla duck tape - it is a small dent - i am very worried - its like a small hole
taping it up is ok. but if the shelf part that holds the shelf broke or popped then becareful it does not let the shelf/drawer hang and keep door open
@@fixitfelix718 bro felix you are the man thank you - i used some food safe dap all purpose silicone to fill the dent - i shouldn't have tried to break the ice with the screw driver - i defrosted - and waiting for it to cure before turning it on i hope the e4 goes away - i haven't tried changing the sensors yet -Blomberg BRFB1051FFBIN thats my fridge what are the parts i need to buy from encompass in case e4 doesn't go away?
@andishae make sure water flushed out drain quickly
Hi. So i DONT have the error, but i do have the ice build up at the bottom. I believe there may also be a build up at the back of that panel because it looks bloated like a belly. Any advice?
Defrost the ice and make sure hole behind panel is clear to drain outnwater i have another video on that some where
@CuriousChoi same swelling thing happened to be (detected when things didn't slide/ close right) shortly after error followed.
Same here.. but on a Summit fridge. Any chance it's the heater or more likely the sensors? Can you test the heater with a multimeter?
Hi Felix, I replaced the two sensors as per your video. Thanks 🙏 i do not see an error code and I opened the back cover after three days to inspect and don't see any ice build up but do see some frozen drops on some of the pipes. Is that normal?
how did you defrost? steamer or blowdryer.....a few drops ok....make sure door is closed and sealed well no gaps in rubber seal
@fixitfelix718 I just left it unplugged for a day. I will check again in a couple of days to ensure no new build ups.... I have a picture of the frozen droplets, can I send it to you for your opinion?
@ahmad.yamani sure fixitfelix718 gma il
What are the 2 different sensors you replaced called? Also how do you check model number?
Defrost sensor and evap senor..if i were you, just because encompass parts..thier #1 parts seller sucks..,,, i would call them and then read off the numbers on the sticker on the side of the refrigerator section..usually starts with brfb#### ...ask for all 3 or 4 sensor in freezer and match them up to the ones in the video...or in that general area..then return or keep the other...its about 5$ each... encompass. Com i believe or parts town. Com. Let me know if that helps
@@fixitfelix718 thanks for your response. I found the model number there!
My issue is When I open the fridge I get a flashing error on the display panel it shows 40 (f) : 10 (d) then flashes to E : 4. With the red triangle & exclamation mark ❕🔺 and was beeping. I managed to turn off the alarm by holding the alarm button. Defrosted my freezer fully and I tried to take the small clip off that you showed had a zap strap in your video and one side of the clip snapped but managed to get it to still sit on snug. I am just going to leave and see if it eventually goes away. I red online it can go away. If it doesn’t in a couple days I will try to again and order the parts from the site you suggested. How long does it take to arrive? I find it a pretty tight area to work in pulling the cords around the sharp areas and I don’t want the pipes to open up like you mentioned in the video. Mine is a built in fridge.
Really appreciate your response Felix!
Does the panel come out with just the two screws at bottom or do I need to do something with the fan on top? Thank you!!
The fan on top is part of the icemaker ..if its the same as the video.
hi! im getting charged ~ 150 for FRZ DRAIN HEATER and ~ 150 for Blomberg Sensor. the blomberg fridge/freezer model is is K56300nebu.Not sure if the parts are specific and different for each model. just curious if im getting ripped off and where i can find parts for cheaper? thank you felix!
1st question is where do you live more or less ..I'll look up what you asked
Not sure which sensor but they are 5 dollars...is it 150 and 150 300 total ..parts and labor? Or 150 plus 150 plus labor ?
Encompass. com call them ask for parts or look online
Hey ..did you see my message
in toronto canada! sorry just saw this@@fixitfelix718
Read description...find my other videos on defrosting blomberg and ice maker repairs!
Question, when I turn it off to defrost where does the water go/draining to? Do I need to be emptying that somehow out too?
Thanks!
Behind the refrigerator into a small tray above the compressor and it evaporates
@@fixitfelix718 ohh ok, thank you so much!
Hi, In my case, shown E4 code, iced in evaporator. replaced evaporator and temperature sensors, the heater core R= 125 oum. same problem. what should I do next? Is there a control board that could be defective? Can find schematic for this freezer? Thanks.
From what I see the heater looks good and e4 should dissapear after a couple cycles
.there was a way to tap in diagnostic mode but I lost the site..email me I'll try to find it...Nd you can flash the board....indont think with good heater and new sensor it will ice up again...if it does its the board....schematics are hard to find for this...I used another models info once and guess how to get into diagnostic..I'll try to send u it..just let it run for a couple days....other comments had the same issue and it dissapeared...
How do you defrost the day before?
shutting off the whole unit
@@fixitfelix718 how? I have a blomberg in a condo unit (build in the wall) I dont see a power switch anywhere
@EmpowermentMentality turn up temp or hold one of the buttons for 3 seconds...on the screen you'll see a " /"0" hold it for 3 seconds...or find the circuit breaker and turn it off over night
Hi Felix,
Where can i buy those parts?
''encompass ''..parts.. google them there ...sometimes links here dont work... encompss parts com
please call them and verify model and part numbers
did you find it?
Hi Felix, when I powered the fridge back on the freezer fan wouldn’t spin. Nothing seems to be blocking it. Before defrosting the fridge the fan was working. Any idea what it could be ? Or does it take a few minutes for the fan to kick in ?
7 hours ago...I'm sure it's spinning by now..if not did you unplug anything
are the fan working afterwards？
@lucywang3830 fan takes like 30 min to turn on unless it's broken or blade is stuck
Hello Felix - I swapped the two sensor cables with the new ones today. Turned off fridge, turned off power supply to the fridge from the switch board. Turned back on. The error is still there - Pls Help!!!
So I recommend either leave it alone like this 3 days it will dissapear after a couple cycles...or whiel the refrigerator is running after 24 hrs...hit the breaker off....leave it off for 1 hour and then turn it on again.....younhad e4?
Read some of the comments some people have this issue and it goes away..check it out
Hello Felix, my blomberg fridge had the same error. I ordered the two parts and replaced them, but the e4 error still appears after rebooting. 😢what would you advice the next step to be?
Did you just reboot it .. i recommend shut off the refrigerator first..hit breaker for 15 min..then breaker on ..then turn on....make sure both connectors were pluged in good and firmly...it will probably go back to. Normal by tomorrow if not let me know
@UWMaBoss, cut the breaker while fridge is ON for 5 hours.
What happen did the guy fix the unit?
Hi,
I dont know how to setup my fridge. Every mode seems to be to cold, and the vegetables are freezing. Am I suppose to put the fridge at 46, 43, 40 or 37??
@@alexandregagne1209 when you shut the door do the lights go out inside
@@fixitfelix718 😭my question is real ! Every mode seems to freeze the vegetable in the fridge.
@alexandregagne1209 yea I believe you but my question is important...you might be missing the fan motor magnet at tip of door so everything freezing because when you close door fan doesn't run
@alexandregagne1209 can you email me your phone number we can talk . "Fixitfelix718" at gmail
The freezer for me works after defrosting but the regular fridge doesn't get cold what would be the issue
there should be a magnet or a white strip on top of refrigerator door that turns on fan....or give it 24 hrs...also needs to defrost fullllly
@fixitfelix718 it still gives me the e4 code but I defrosted it for 2 days already and the fan still doesn't kick on
I did this now I have an additional code E-1 and E-4. I reset the fridge and they still come up.. Now what would you recommend?
Not sure... e1 I think it's power fail but I have 2 numbers for tech support
8883522356..8004599848.... you can try this the 888 is for technicians I believe...just pretend you are and try to get the answers .....I looked for my cheat sheet on errors but I can't find it...
You replaced parts alredy?
Additional code ...maybe the thermistor was on the wrong pipes or the code will dissapear on it its own over a day or so once running properly
Yes I replaced the exact parts you list in your video@@fixitfelix718
I put them where you directed.......
Hey sent you an email. Trying to ID these 2 parts I need to buy. Let me know when you have a chance
Thank you!
Thanks! Fixed, except it wont reset the error code. Holding power button turns it off and on, with error code returning immediately. Unplugging doesn't work
Did it reset the code ever?
Yes, I cut the power from breaker while fridge was ON and I didn't restore it for several hours (maybe 5?) and it did reset. Purrs like an error free kitten now (after your fix, thanks).
Awesome congratulations!
turns out, it didnt reset because of power cut but simply time elapsed. So turn off and on, then ignore error, should clear in 3 days
What is the model no. for the defrost sensors?
Best bet is to type you model number into encompass parts . Com and search..because it could be different
Send my your model stick to my email ill check
K56300NEBU is the model no. Marketing Code isBRFB1050FFBIN
Thanks for your help
@@Dreams1954 ill check tomorrow morning..where u located
How to turn on the defrost mode ?
Not easy you need to.find the service manual I lost it and even with manual I'm not sure...I think when you turn it on and off it starts in defrost sometimes. Usually I replace sensors after a manual defrost and in a few days it refreshes the code
@@fixitfelix718 i got it. But i did have E4 error code. I checked all sensors ( multimeter) and there is resistanse. Ok. I'll check it out. Thank you
@@pavelmedvedev358 probably the heater is OK usually sensor fails and back when I made the video I couldn't figure out which was which so I just always do both on top.
@@pavelmedvedev358 the resistance depends on the temp of the sensor and I don't know the parameters of those thermistor but in a warm cup and an ice cup you can measure the ohm but i dont have clue what temp equals which ohm...could be out of range when in the extreme temps. No idea
@@fixitfelix718 my bad, i had to say that i did not have any error codes. ok. should be fine