Thanks , I enjoy your video. I just acquire one , but there is something wrong with the inner selection knob. I hope I can get it fixed as I really like it. 😅
При намотке ниток нужно повернуть влево рифленый диск на маховике справа и тогда крутится только моталка ниток. Сейчас восстанавливаю такую машину после наводнения - очень понравился механизм. Не забывайте менять смазку в картере челночного механизма!
@@4anat пробовал, кругом где типа есть мануал просят денег, но не факт что есть. странно что на офсайте нет этой модели. еще и не комплект, этих шестерней зигзаговых нет, судовая машина, +100500 строчили кривыми руками, куча проблем теперь с ней.
@@19BAG75 Шестерни съемные -это копировальные диски, по ним разные фигуры строчат. А так машинка простая. Смазать вовремя и зазор проверить между иглой и носиком челнока. Там еще картер есть под челноком, в нем густая смазка, поменять, скорее высохла.
@@4anat картер ?! это такая металлическая коробочка на дне машинки ? кстати, не в курсе как разобрать натяжитель нити, что то он глючит, нить более-менее проходит только при установке на 0 я частично разобрал его, до тарелочек, а дальше хз. как.
I noticed when you start sewing you manually turn the side towards you Is this to get started as I have tried sewing with one of these machine and couldn’t understand why it wasn’t sewing and moving the foot Please can you confirm Thank you
When you wind a bobbin the needle is not supposed to go up and down it should stay still, so that’s not right pushing the bobbin lever should disengage the needle mechanism…?
Yes in winding the bobbin the needle is not supposed to be moving, but most times people forget to screw back the knot on the wheel, hence I rather leave it and wind the bobbin with the needle moving
But then it wouldn't be the same. It would become 'just another sewing machine'. I have a manual sewing machine...it came with a motor I could add if I wanted to, but, I don't want to.
@@bondmachines my anuty gifted me the machine, have been trying to get a needle for it. I got our normal needle for butterfly but it's not entering the needle space. Please what needle does the does the janome 752 uses?
@@faithadeyemi it may have dirt accumulation in the needle channel, keeping it from fully entering. I seen this before. Take the needle clamp off and clean
I thoroughly enjoyed your demonstration video. It was excellent. The Jenome / New Home 672 machine is a beautiful looking machine.
Yea it sure is.. One of my personal favourite
Thanks , I enjoy your video. I just acquire one , but there is something wrong with the inner selection knob. I hope I can get it fixed as I really like it. 😅
Yeah it can be fixed...
При намотке ниток нужно повернуть влево рифленый диск на маховике справа и тогда крутится только моталка ниток.
Сейчас восстанавливаю такую машину после наводнения - очень понравился механизм. Не забывайте менять смазку в картере челночного механизма!
Привет. а инструкции к этому аппарату нет случайно ?
@@19BAG75 Не было , интуитивно, принцип одинаковый. Но можно в интернете найти . But you need to understand Engish or other languages, ok.
@@4anat пробовал, кругом где типа есть мануал просят денег, но не факт что есть.
странно что на офсайте нет этой модели.
еще и не комплект, этих шестерней зигзаговых нет,
судовая машина, +100500 строчили кривыми руками, куча проблем теперь с ней.
@@19BAG75 Шестерни съемные -это копировальные диски, по ним разные фигуры строчат. А так машинка простая. Смазать вовремя и зазор проверить между иглой и носиком челнока.
Там еще картер есть под челноком, в нем густая смазка, поменять, скорее высохла.
@@4anat картер ?! это такая металлическая коробочка на дне машинки ?
кстати, не в курсе как разобрать натяжитель нити, что то он глючит,
нить более-менее проходит только при установке на 0
я частично разобрал его, до тарелочек, а дальше хз. как.
I like tp.order one set.janome,,,672
Price
How to order
I h been 20yrs back
It.a best mechine i h come across!!!
Ok.. It's available.. What's your country of residence?
Thanks for sharing sir.
Nice mechine. I have one too
I noticed when you start sewing you manually turn the side towards you
Is this to get started as I have tried sewing with one of these machine and couldn’t understand why it wasn’t sewing and moving the foot
Please can you confirm
Thank you
I used my hand cos the belt wasn't right at the time.. In your case, check the feed-dog regulator if it's up or down
Please i need your help, my new home 672 is not sewing. Please what could be the cause? I will really appreciate it if you can help me with it
What's the issue with it
Hello, What country are you in?? Does the disc cam fit any of the old janome model? Do you sell the disc cam?
Lagos Nigeria.. Yes it fits... Presently I don't have it..
@@bondmachines please can I get notified whenever you have it?
Ok
Hi! Could you post a video on how to use jenome sewing machine model 673 pls thanks
Ok no problems..i will
Good morning can i get the discam for new home model 672
Yeah..
Please show how to use jsnome 802 model
Will do, when I get the machine.. Okay!
Where can I get the disc cam for my machine? Mine came with only the zigzag
It's available,2k per disc
When you wind a bobbin the needle is not supposed to go up and down it should stay still, so that’s not right pushing the bobbin lever should disengage the needle mechanism…?
Yes in winding the bobbin the needle is not supposed to be moving, but most times people forget to screw back the knot on the wheel, hence I rather leave it and wind the bobbin with the needle moving
How much price nowadsy
I want to buy 1 set
I have 1 set ,20yrs back when young !And h extral 4pcs red zizag dic free
Janome 672 is best mechinr
Please what's your country of residence
Do u also have the disc for Janome 671
Presently I don't
Mi maquina hace unas punteadas y no cose y vuelve a coser y vuelve a dejar de coser😢😭no se que hacer
Pls what is the needle type for this machine
HA and DB
Un video de como regular el cangrejo por favor
Please how can I get the disc?
hola como debo hacer o que puntadas sirve para coser un buso cambie de aguja pero no cose
Did you thread the machine properly?
Way do this machine top thread?
Should be add a sewing motor
Will better easy sewing works
But then it wouldn't be the same. It would become 'just another sewing machine'. I have a manual sewing machine...it came with a motor I could add if I wanted to, but, I don't want to.
I want to buy a 672 model matching
Pls how can I get the disc cam
I've got them available
I have to a matching,what can i do?
I don't understand your question
does anyone have the instruction booklet in pdf please? I need it for my mother
The manual I have is in Japanese
I have the english version manual.
That's great!! Can you send to me?
How do I fix my needle for this machine?
Front threading mechanism.. Groove side facing you
@@bondmachines my anuty gifted me the machine, have been trying to get a needle for it. I got our normal needle for butterfly but it's not entering the needle space. Please what needle does the does the janome 752 uses?
HA or DB needles..size 14-21
@@bondmachines I mean Janome 672
@@faithadeyemi it may have dirt accumulation in the needle channel, keeping it from fully entering. I seen this before.
Take the needle clamp off and clean
No se como poner en recta 😢
Pm price
You mean the price?
Traducir en español x favor
Chile!!!!
I am Sri Lanka. I won't to design disk
Presently I don't have the disc cams Available
Puede hablar en español,no entender nada
Please write in English