Guide of replacing the motherboard of ender3 with BTT SKR MINI E3 V2.0 and BTT TFT35 E3 V3.0
HTML-код
- Опубликовано: 30 сен 2024
- BTT SKR MINI E3 V2.0 and BTT TFT35 E3 V3.0 was designed by BIGTREETECH. We are committed to easy printing, easy life.
BTT SKR MINI E3 V2.0
1.The TMC2209 driver use same physical UART port, which save IO and increase the stability of motor drivers.
2.We increase an double Z-axis interface on the motherboard which can work on printer with single or double Z-axis.
3.We set a EEPROM( AT24C32) on the board , so data storage is more stable.
4.Printed circuit boards of SKR MINI E3 V2.0 have 4 layers, which prolong the life of this board.
5.Power chip is MP1584EN and increase the current output which can reach to 2.5A.
6.We add protective device to interface of thermistor.
7.We also set two numerical control fan and a interface (PS-ON) for automatic shutdown after printing.
8.SKR MINI E3 V2.0 also supports BL touch, filament run-out sensor, power-off resumed printing, and automatic shutdown after printing.
BTT TFT35 E3 V3.0
1.ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz;
2.Upgrade the firmware by SD card. It is easy and convenient to operate.
3.This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode.
4.Serial port screen mode supports two printing modes: SD card and U disk.
5.Reserve WIFI port, and WIFI function is realized by external WIFI module；
6.Reserve the extension port of filament breaking detection (FIL-DET)；
7.Reserve the extension port of automatic shutdown after printing (PS-ON);；
8.LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) ；
BIGTREETECH:www.bigtree-tec....
Facebook: www.facebook.c...
Twitter: / biqu_hope
Instagram: / btt_daisy
Please make a video about installing firmware for bltouch
ender 5 plus, with this setup--"no printer attached" message. checked baud rate and made sure it was correct, even tried all the other rates just to see if one would work--still "no printer attached".
How do I fix " no printer attached" did everything right and keeps getting this
second this!
Did you find the answer ?
Yes there is a second cable for the LCD touchscreen seeded its black and replaces the rainbow cable
@@harrymorris9345 Yep, the black 5-pin cable(?). I can print from Marlin mode when both cables are connected. Only touch UI "works" when black cable is connected, still in both scenarios I get "no printer attached". Baudrate thing is same in firmware and settings. Don't know what to do next
At 8:34, it mentions the black wire is connected to TFT interface. The black wire has a plug with 4 wires together and one by itself. Does this end connect to the TFT board or does this end go to the LCD display? Also, with the single black wire, does it attach to the front of the printer (closest to the USB and Micro USB drive) or does it go on the opposite, farthest end from the drives?
hello, this is a late reply but maybe helps someone in the future:
Yes, you need to plug the wire that is alone. The best way to describe the right position of it is to place the wire in the opposite direction from the SD card slot (The four wires that come together are more close to the SD card position and the isolated wire goes in the remain slot).
I hope that this might help
WHY you don't have a guide where you can replace on Ender 3 all of it. Motherboard, TFT35 screen, smart filament sensor and BLtouch??? OR make a firmware.bin file or configuration.h for marlin. And all combination of it.
Request for you at BTT. Include a cable of the length in the video. The cables bundles with the V3.0 is way too short. Don't know what that's all about.
I used my stock cable and it works fine.
Would love to see a firmware video for the Ender 5 Pro using these
To be honest, I think this is THE best chinese instruction I ever got!
Oh and just one thing: next time please charge a few cents more and make the display cable a bit longer. It's a pretty tight fit.
I’ve installed both in my ender 3. Works perfect. Awesome. When Will you do a video with the bltouch instalation?
did you have to install any firmware or was it as straight forward as tech showed?
I just got the SKR mini E3 1.2 and the TFT 35 E3 , Install went great and thank goodness the TFT35 has SD and usb card reader because the main board Micro sd card reader does not work I'm not sure How I will update the Marlin firmware when the BL touch arrives. Is there a jumper or something I can check to see why the micro sd card reader is not working? I have tried 2 micro sd cards and they both work on my computer but neither work on the main board, Thanks for any help..
i mistakenly bought the skr 1.4 turbo and can not get it to work with my ender 3 pro with the tft35e3 do you have a bin file i can download so i dont have to compile anything
i also have issues with my btt skr1.4 turbo board - it does not boot and BIGtreetech is not really helping me - i keep sending them info on my board but they dont want to replace the board - i have been struggling now for over 4 weeks with this board, nothing works
Hi.
after I switched to new motherboard BIGTREETECH® SKR MINI E3 V2.0 on ender 3 pro, the printer moves to the end at X axis, end the table has also moves out after each layer change, I thought maybe there was a bug in the system.
can you please turn the very load music down, which is drowning out the description.
Why do you not respond to the issue problem I replaced the original Ender 3 board, in my printer, with your board? I have tried contact you, via your website, and I keep getting the message the 'Page Does Not Exist'.
Hi, Could you send the email to service001@biqu3d.com? Sorry for the inconvenience.
Works great on Sovol SV05 as well! Thank you BTT
Thank you. This was not the hardest part. Now the configuration of Marlin please.
Then: could this board be used on a printer with dual hotend?
how to do the same for anycubic mega zero 2.0?
Thanks! I recently ordered these from your store on AliExpress. I can’t wait to get them!
thx for your supporting
For some reason my TFT connector is split so one pin is separate, and you don't provide instructions on which orientation the TFT connects to on the motherboard...
I'm currently dealing with that.
On an SKR Mini E3 V2.0 board, the split single reset connector goes on the TFT pin closest to the power supply inputs. (Eg. If you look at the board so the labels, such as “TFT”, “PWR-DET”, “E0-STOP” are right side up… the single connector goes to the first TFT pin on the left).
It’s the one with the square solder pad in this PDF: github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/blob/master/hardware/BTT%20SKR%20MINI%20E3%20V2.0/Hardware/BTT%20SKR%20MINI%20E3%20V2.0-PIN.pdf
@@lucasthompson1650 Thanks I figured it out after putting them on wrong at first then reversing them. :)
How do you wire the bl touch to the board ?
Is this compatible with the E3D Hemera?
This is a joke right? BTT firmware doesnt work and has rendered my printer unusable until i learn how to compile my own firmware. stay away from this unless you plan on spending all your printing time trying to fix stuff
Dont know if your still having issues but worked fine for me, just need to do your research. I did not have to compile anything. Was able to get all files from the github. Some searching on RUclips and Google helped
Can I use Bigtreetech skr mini E3 V2 in the 3D printer I made myself?
hi, friend. Please send me more details through messenger on Facebook. Our technical support can recommend.
How do I use ps on? Do I need to install any module?
I connected up the hotend fan in the exact Same place as shown in this vid but I can't get it to work, maybe a faulty connector?
Hi! You could contact our tech support via email: service004@biqu3d.com
What do I do with the 5 red jumpers in the bag. Because on your website they are already installed. Do I need to install them or not ?
Good question, been looking for that answer myself but there is a horrendous lack of information available on this board even on their official website.
The jumpers are only used for sensor-less homing.
Mine heating to maximum when I turn it on
Caused me so many errors...Do not buy
我只想知道，为什么bilibili不更新？？？非要墙外来看。
I have Ender 5 with skr mini e3 v2.0 after 1 month board and lcd blank . Can you help me?
I have just trying to install boards and followed your video, all worked well but had one big problem it will no read the sad card. Tried many sad cards that were working on the original board all had the same error. When I insert the sd card the screen displays card inserted. I am assuming that this is a faulty board. Any help is welcome
Great board very silent. But I cannot connect my laptop or Rpi via the usb port. How do I setup skr mini E3 with octaprint?
Have you all made a board for the Monoprice / Wanhao Duplicator 6? That board craps out on this otherwise nice printer I saw there is a marlin 2.0 for these printers just need a quality board in it, I have SKR in my Endr 3pro and love it!
I upgraded my Ender 3 to this exact combination of SKR Mini E3 V2 + TFT 3.5 V3.0. With the stock SKR firmware the display works in both Marlin and touch modes. If I download any version of Marlin, including the BTT-created version, I cannot use the touch feature of the TFT - no printer connected.
I've been looking literally for weeks for guidance on configuring the Marlin source code so the TFT works in both modes. No luck! I can only get it working in touch mode with the binary included with the board, which does not support my filament runout sensor or BLTouch!
Please, please, please tell me how to configure Marlin for the TFT 3.5 V3 so I can configure my runout sensor and BLTouch.
i installed both the skr mini E3 v2.0 and the tft 3.5 E3 v3.0 today and all i get on the screen is 2 lines across from left side to right and in backgroung is the marlin and touch icons. nothing works. and the sm chip on the touch screen gets really hot
If you purchased your SKR mini as a package with the TFT display I would avoid upgrading the firmware. I installed the board and display and all seemed fine until I tried to print from the SD card, immediately got an error trying to read the file. I though hey lets update the firmware, now I have the lastest firmware but the TFT no longer communicates with the board "No Printer Connected". I only bought this as a package to simplify the upgrade and it didn't even work properly out of the box, firmware updates only made the problem worse. Unless you have some compelling reason to go 32bit I'd avoid the aggravation this update creates :(
Vs code needs to be updated to accommodate the version 2 board, also when you build your own firmware it fails on around 5 things that need updating in marlin I guess. (Including board unrecognised) anyone found a work around yet? Bigtreetech own complied firmware on github also fails. I think these products are fantastic, I have v1.2 at the moment and V2 on the way. I need to compile my own firmware for auto bed levelling filament detection etc.
hello
I have connected the layer parts cooling fan and the electronic box fan as you said, but none of those fan seems to work. how do i fix this?
Installed, and runaway bed heating problems. Jump through hoops, get visual studio, bla bla bla. You know what, shove your board.
I've had both for a while now. At first I had some issues but some research on RUclips and Google helped me in the end, also I didn't have to compile anything
Hello, how can I connect a leser kit with a 3-pin connection: 12v, Gnd and PWM? Thank you
Is the V2 compatible with BL V3.1 also using Octoprint out of the box without any FW upgrade?
Hi, I have a problem in my Ender3.
Motherboard skr mini E3 v.1.2 with display tft24, but don’t run.
If I turn on the printer the output on the display is :”illegal Flash App”.
Can you help me?
Does the Display also work without using the new mainboard?
It’s a shame that when in touch screen mode and goes to print strange things happen eg shoots off to the far right corner and then fires out a load of filament at high speed. Using the stock board and stock touchscreen firmware. When in Marlin mode no problems at all.
Hi!! This motherboard works for Ender 3 PRO? Thanks.
Hola, justo hace unos dias me llego el BTT SKR MINI E3 V2.0 y el BTT TFT35 E3 V3.0, pero tengo un problema ya que instale todo bien, me funciona perfecto al encenderla , pero tengo un problema y es que el puerto del SD MINI no me lee los las memorias... solo puedo imprimir conectado un pendrive desde el TFT, ayuda por favor para solucionar este problema
Im using this without a screen but im not able to print via usb like i was able to before. Is there a certain reason for that?
Lose the silly background music and increase the volume of the narration. The reviews of bigtreetech boards does not instill confidence regarding quality control and durability. If the results were on par with the ads and descriptions, this could be a real winner.
hello the power-off resumed printing how to enable this feature?
Hello, is Skr mini E3 V.2 compatible with Antclabs BL touch?
Not at this time. The firmware is on github but it does not seem to work for anyone. I just fails to probe the bed.
Yes mine was with vers.3.1 but I would think that you have to make sure it is a genuine BLTouch. My only problem was that after installing the firmware from BigTreeTech Git site I expected to see the BLTouch on the main menu, it is hidden away in the Configuration menu. Once I found it and pre levelled with a piece of paper , set the offset and works great. Tested on a benchy with no problems at all even the letters on the bottom are far better than before. I am now waiting for the touchscreen to arrive as it was dispatched 4 days after the board for some reason.
@@stuartalexander3
thank you very much Stuart. I have ordered Antclabs BL and BTT screen touch for Skr min E 3. I should receive them within nexr few days.
The fact that we can flash firmwares tor updates through simple SD card is very practical for me as I am not a programmer. Thanks BTT to make flashing process accessible to novice users!
In addition to that I very happy to have now Skr mini E3 V.2 installed on ender 3 pro with Marlin 2.
Zoé Ketchoz , I ordered the board BTT SKR MINI from BigTreeTech and it arrived after 12 days to the U.K. I ordered the touchscreen a few hours later and that has not arrived yet possibly due to a different supplier than the board. Creality have a lot to learn as their firmware site is pretty much useless and the fact that they sell the silent board but no firmware for it as supplied. I downloaded the BLTOUCH firmware from their site and it refused to even show up anywhere. Creality tech help is non existent therefore with the BTT board and their excellent firmware site my Ender 3 is good for the mechanics but useless with 8bit boards etc. BTT seems the only way to go. PS you will need to switch the poss and neg lead over on the connector before connecting to the board, only takes a couple of minutes.
Keith Zimmerman , have you changed over the leads on the VCC connector. Leave the signal where it is but change the other 2 over.
try fixing the firmware, as it's riddled with bugs and pointless having if that doesn't work.
Is it compatible with the original lcd screen?
do you apply hot glue like the stock motherboard? is it safer to apply hot glue? or does it matter?
there is no need, the glue is there to hold the connections for shipping.
Hi. I just installed both of this but had a "No printer attached" error. I tried changing the marlin configuration.h file as someone suggested to
#define SERIAL_PORT_2 0 but it says port 0 does not exist. Please help to solve this problem. Thanks!
Also the touch screen mode isn't able to access the onboard sd card and it will hang when selected. But in the old marlin screen it works. Any solution to this? Thanks!
I just experienced this same issue, I hope you get some help.
When connecting the Z motor cable, there is a ZAM and a ZBM on the motherboard... which one do I use and which one is left empty?
use ZAM. ZBM would be used if you installed a second Z-motor and lead screw.
no firmware works sadly, i have tried now 4 different branches and no joy
Can you use the stock screen?
does the SKR board not work with the original ender screen?
It can work with the original screen
Hi, will this work on my cr20 pro
Great Video. Very useful. I installed my skr mini e3 v2.0 and tft35 e3 v3.0 on my ender 3 pro without any problem. I miss a bltouch section. Please make a video with instructions to have the bltouch 3.1 working on these boards.
I just installed the board on my brand new ender 3 pro and it's crashing into the x and y switch
Thanks for making this video. It was very helpful to me during installation. Very nice screen. Good touch screen and menu implamentation.
Is there any short circuit protection?
Good video! Is it possible to use the TFT USB or card reader to read G-codes?
I just installed the TFT35 v3 on my ender 3 and can confirm the USB and SD card reader can be printed from and is hot swappable without the need to refresh etc.
Will this work with the original ender 3 screen?
Yes
Где купить плату?
www.bigtree-tech.com/shop/product/show/id/40
nice
Thank you. Your instructions are great
What’s the red jumper and how do I know what positions to use for my Ender 3 pro?
the red jumper on the board for power, The factory setting is 5V. If you use the E3 DCDC5V V1.0 module, you need to change the jumper to the other end.
Do I need to buy a different screen or can I use the stock screen?
you can use the oringinal screen of ender 3, but it only has marlin mode.
@@bigtreetech5117 I have the original screen. I can not save e-steps when I change them.
Might want to make note of the hot glued connectors like I hane on my Ener 3 Pro...
Installing mine today!
Can’t wait to get this, I ordered mine directly last week, Hope it gets here quickly
Good idea. I paid extra to get mine Thursday and BL Touch is not working. By the time you get it they will probably have a working firmware for BLT.
@@KeithZim we update our firmware of bl touch, you can try this new link github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/blob/master/firmware/V2.0/README.md
I can’t get it to work
I’m literally about ready to chuck the board into the road and run it over along with the screen , I got it just today and I had everything plugged in from stock to this and it lights up red on the skr board and red on the TFT screen loads “marlin” and “touch screen” I try clicking and using the knob nothing doesn’t respond.
Thank you
Sweet chinese accent :)
Was that Chinese ?? Good thing there are subtitles !!
Good product!
Does it work for Ender5?
It is capable with ender3, ender3 pro, ender5 and CR-10.
Can you do a tutorial on installing the firmware from the github page?
thanks for your suggestion, we will consider
@@bigtreetech5117 please do this as soon as possible
It’s not that hard, go to the Githib page. Go to SKR E3 V2.0. Navigate to the firmware and download the one that you want weather it be the ender 5 or ender 5 with BL touch etc..... Once you download the firmware you want Name it firmware.bin and put it on your SD. Then take the SD put it in your board and ta da your done. Also, it says this in the instructions PDF for the board so if you need any more help look there. It’s also on the github.
if you lose the music i might watch your video's i cant understand a word your saying
10/10 - I'm using it with ender 5. This board is great: silent motors, easy install and amazing documentation on github. Support for BLTouch probe on this board improved the printing experience a lot.