@@liod_9 Сейчас в велосипедах подшипники не как раньше, сейчас без кареток просто шарики засыпаются туда и конусной гайкой зажимаются. Пока гайка или сам барабан не сотрутса...
Good to see you wearing proper gear for welding I burned the hell out of my arms welding under a trailer from the hot sparks falling on my arms I'm polka dotted with scars on my arms had to get the job done first and last time I do that again!
great machine if you have a small tub or bucket under the sparks from grinding you can quench the workpiece and it will catch most of the sparkes and rubbish
Sek! thanks men.. i watched a ton of diverent beltgrinder vids.. i already made a frame using your V cutting technique.. i'm now creating the tracking and tension part..my original motor is not strong enough.. so i'm going to buy a angle grinder and use that for the power..[i saw this vid a few weeks ago.. i lost it but just now found you back again!] i'll post a video and send you a link when i'm ready.. thanks again for this build!!
Your Dog sure was staring hard at the door lol. Do be careful when welding anything Galvanized as the smoke put off when the Coating is burned Is Highly toxic.667 It has killed those who didnt use good ventilation and inhaled to much. One of the 1st symptoms of being poisoned from Galvanizing is a headache from hell. Itll make you nauseous the headache is so intense.
Only thing missing now is a water drip so you can cool knife blades while you're sharpening them. I'm sure you and your trusty welder could work that one out. Otherwise it's a wonderful machine. Well done!
Great job,real nice design..One thing to think about.Cut a 3/16 deep groove in the wood roller.This will also help the belt from wandering.Keep up the great work Whats next.,,?
While it shows a good result,........it's extremely difficult to weld things square. But it shows many ways to keep the cost down. People pay 1000 times too much fur these thing's.,......like its an industry standard or something.
I mean if you use a welder a decent amount ... you should be fine.. practice and anyone can weld straight , just don't think your going to weld something square the first time you pick up a welder.
If you want to make your piece square use tack welds to set your piece to your desired angle. If you check your angle after each tack,once you get 4 points tacked it shouldn't move. Plus if your angle isn't right you can cut the tack weld easily and reset for the angle you want.
I really like your project I think it has a lot of potential. But the biggest thing and I see wrong and I don't know if anybody has mentioned it cuz there's a lot of stuff here that I can't read, the fact that you're welding on galvanized steel is a big No-No!!! It gives off a lot of harmful gases, when heated will kill you!!! Someone had mentioned about grinding off the galvanized before you will and you will find that you get a better Arc. I say don't even entertain the idea of welding on galvanized without the proper respiratory equipment. Other than that this is one of the best belt grinding builds and one of the easiest belt grinding builds I've seen to date great job
Cool build. I'm liking it. Might give it a go. All you have to do is drink whole milk and the galvanizing poisoning will go away just like Irish potatoes on your eyes when you welder burn them. Is it bad to breathe yes, should you breathe it no, but in the event you have a sick belly and can't breathe drink some whole milk. Done it for years and I'm still here.
Great video Iv built my forge Iv got a R×R track anvil and Iv fabricated everything I need to do blade smithing. Iv been using a hand belt sander. I now know what my next built will be I'm gonna add narrow wheel pulleys as well to do detail work That's killer .Wow Bro You could build a metal lathe with that motor lol . Thats the same one used to turn Jupiter. It's a multi tap motor You can go 120 or 240 Single or 3 phase Isnt it.
Тоесть чтобы сварить три железяки для собственного пользования, просто необходимо быть сварщиком? Ну тогда я универсал, а вот деньги мне платят только за дальнобой.
Expired Deadlines он сварщик любитель и может себе позволить варить в плавках , без маски , и еще можно без защиты на болгарку . лично мне так тоже удобней особенно в жару.
Yeah that's a man, but have you seen all the comments of people complaining about it? Talking about "good job now go buy proper safety gear" bunch of sissies if you ask me. I'm not gonna spend 5 minutes putting on all my gear to run a 1inch bead. A friend of mine is always bitching at me about wearing gloves, and I always tell him the same thing, I'm like there called MAN HANDS go get you a pair.
Finally somebody mentions the galvanized piping. You shouldn't be welding or forging anything that contains galvanized material it gives off poisonous gases that will kill you!!! Other than that great job I look forward to seeing more from you.
i was recently welding on a yard trailer i built out of bed rails and closet shelves. i used zinc plated bolts for the axles and ground the zinc coating off. thought it might mess with the welding so i removed it. mild steel does not agree with alloys very much.
Great job on that tool. It would be simplier to just buy one. But then you wouldn’t have nearly the fun of making it. I’m not good with angles but i absolutly love to use my wire welder. Anytime i can put all my tools to work is like therapy for me. Again great job.
I go to work in crocs &shorts I get teased before I put my steel toes boots and pants on & I get pretty dirty and they say put some pants on when I get to work😁 job title mechanic/labor
@Keith Sargent Why the hell would they scrub him with a scrub brush?!! That's really not a good idea when trying to grow back some skin - actually it's a terrible idea!
You're a very talented person. Thank you for sharing your project. One thing I noticed. It looks like you are welding galvanized square tube. I always grind back the galvanized part before welding. Some of those welds may be questionable.
Sacanagem eu paguei quase $3000 em a lixadeira compacta, vem um Áustriaco, meu pai era Áustriaco ,e faz a lixadeira top e relativamente a acessível ao bolso kkkkk parabéns pela ideia amigo,!!! Herzlichen glückwunsch zu diese idee, Danke Mein patrizier !!! 🇧🇷🇩🇪🇦🇹🇦🇹🇦🇹
I would have to build the frame from wood, find an old bicycle, buy at least two belts and have the time to do it all.This is an absolutely awesome idea if you have all the stuff to do it on hand but in reality people like me that only have a few basic power tools would be have a pretty hard time building this but like i said it a ABSOLUTELY AWESOME IDEA !!! I GIVE IT THREE THUMBS UP !!!!! No i didn't say that wrong Diy'd an extra thumb using scrap cardboard and a hot glue gun... Lol Im kidding really but any ( life hack ) video that's popular these day's HAS to have cardboard and a hot glue gun.
Thats awesome, but without bicycle hub also we can do it I guess. Actually, what's the main function of bicycle hub here. Can't We can do it with bearings and motors? Pls give suggestions coz I don't know the function of bicycle hub.
Критиковать не буду, в комментариях замечания правильные и справедливые. Я о другом. Множество видео о гриндерах замечательные, можно брать в изготовление. Но почему-то у них подручник приварен к раме (каркасу, основанию, старине). Что резко сужает возможности станка. Неужели так тяжело для самого себя сделать его регулируемым? Даже при отсутствии материала, станок делаешь - остатки всеравно остаются. Ну хоть бы кронштейн и резьбовая пара. Совершенно непонятно... За работу и прилежание, при всех недостатках, всеравно РЕСПЕКТ! 👍👏🤗
Много я пересмотрел гриндеров.Это конструкция самая простая и надежная.Сразу видно что руки из нужного места растут! Зачет!))
да ну нах. скоро велосипедные втулки будет менять.. там подшипники просто смешные не рассчитаны на такие нагрузки.
@@liod_9 Too bad he didn't use more of those big roller bearings instead of those bicycle wheel head things..
@@liod_9
Конечно. На таким оборотах греется солидол и вылетит там даже нет пылник.Сухой подшипник через полчеса начинает шумит 😃😃
@@liod_9 там не от stelsa подшипники 😀
@@liod_9 Сейчас в велосипедах подшипники не как раньше, сейчас без кареток просто шарики засыпаются туда и конусной гайкой зажимаются. Пока гайка или сам барабан не сотрутса...
Самое прикольное здесь, что сварщик работает в шортах. Сразу видно - наш человек!
он же австрияк
и перчатка одна)))
я сначала подумал что он в гермаке от мотика варит
@@АлександрИванов-ь1ч2з а мне сперва показалось что у него левая рука протез
@@ЕвгенийР-ч5з LO
Good to see you wearing proper gear for welding I burned the hell out of my arms welding under a trailer from the hot sparks falling on my arms I'm polka dotted with scars on my arms had to get the job done first and last time I do that again!
Battle wounds.. be proud of your scars.
Nothing like a welders tan.
You mean like the flip-flops & shorts he's wearing lol
Если-бы все занимались ремеслом, помимо своей основной работы по призванию, то в Мире не осталось месту для всякого рода распри !
Браво Маэстро !
А у кого-то, именно распри,это его главное ремесло !🤗
having time to think is vary important, and it is awesome when a person can think of things that can be used to help many others.
With the most humble of tools, this man made a very nice machine. Fine job.
Похоже, что человек делает уже не первый экземпляр. Движения уверенные, отработаны.
.
Я у него посмотрел как болгарка на тисках установлена,как отрезной станок,классно.🤔☝️
Если это не 1 экземпляр !!! то почему не догадался , как то исключить полет искр в лицо ?
Love how this guy works in shorts and sandals. No worries here with hot work.
That's the most powerful motor I've seen on a DIY belt sander/grinder.
He makes do with what he has.
Well, looks can be deceiving. I have one 3 phase motor, maybe bigger than this, has only 800W. Can be pushed safely up to 2kW, but...😅
Para sa mga hindi makabili ng belt sander.
Sana may maliit na version para pangtanggal ng mga spot welds sa kotse. Magaling, kabayan.
I really like that you are using recycled parts in this build.
Ну и я на импортном языке напишу.
Работа супер. Особенно идея с втулками от велосипеда. Спасибо.
Удачи в работе.
Absolutely fantastic safety precautions. Only one glove, bath slippers... etc. Wonderful example for newcomers.
I can't tell if trolling or serious
Лучший самодельный гриндер!
nice project, simple, functional and affordable for many. Well done buddy!
great machine if you have a small tub or bucket under the sparks from grinding you can quench the workpiece and it will catch most of the sparkes and rubbish
За шкив на двигатель- отдельный лайк !
Sek! thanks men.. i watched a ton of diverent beltgrinder vids.. i already made a frame using your V cutting technique.. i'm now creating the tracking and tension part..my original motor is not strong enough.. so i'm going to buy a angle grinder and use that for the power..[i saw this vid a few weeks ago.. i lost it but just now found you back again!] i'll post a video and send you a link when i'm ready.. thanks again for this build!!
Wow! Yes please. Thats great i hope you would have a good results
Wild looking contraption you have there. But very unique way to make a belt grinder
Well done . I don't know if I'm happy that I found this , suggestion , or mad because I didn't think of the bicycle hub myself ! Thank You .
PARABÉNS, a melhor lixadeira que já vi, super bem feito, fiquei torcendo até o final para dar tudo CERTO 😃
Abraço aqui do Brasil 🇧🇷
Your Dog sure was staring hard at the door lol. Do be careful when welding anything Galvanized as the smoke put off when the Coating is burned Is Highly toxic.667 It has killed those who didnt use good ventilation and inhaled to much. One of the 1st symptoms of being poisoned from Galvanizing is a headache from hell. Itll make you nauseous the headache is so intense.
Thanks for the concern bro actually didn't know the effects of the galvanize fumes. Luckily you mentioned it :D
@@SekAustria I had heard of it being deadly long term as it has a lead base. But The short term sickness has been called Metal fever or Flu.
Only thing missing now is a water drip so you can cool knife blades while you're sharpening them. I'm sure you and your trusty welder could work that one out. Otherwise it's a wonderful machine. Well done!
Ульвовіі
Great job, now you have ur own belt grinder. Nothing like making and using your own tools.
Great job,real nice design..One thing to think about.Cut a 3/16 deep groove in the wood roller.This will also help the belt from wandering.Keep up the great work Whats next.,,?
We made one almost like this years ago for our fab to sharpen soap stone [chalk] on. OSHA fined us 7500.00 for it because no guard on it.
While it shows a good result,........it's extremely difficult to weld things square.
But it shows many ways to keep the cost down.
People pay 1000 times too much fur these thing's.,......like its an industry standard or something.
I mean if you use a welder a decent amount ... you should be fine.. practice and anyone can weld straight , just don't think your going to weld something square the first time you pick up a welder.
If you want to make your piece square use tack welds to set your piece to your desired angle. If you check your angle after each tack,once you get 4 points tacked it shouldn't move. Plus if your angle isn't right you can cut the tack weld easily and reset for the angle you want.
Maybe add a guard at the top roller as I saw stuff flying at your eyes from there. Gotta be safe. One day I will copy this great idea.
Можно ли пояснить, для чего узел натяжения ленты сделан из массивных подшипников, а не из той-же велосипедной ступицы?
Может ступиц не хватило) а подшипники были.
Алексей Шелковников Агааа!
@@Alex-Hippi как вариант 😉👌
логичное замечание кстати
OH! dear you are great 100% contribution at our society,lot of thanks.
А я поставил лайк, работа мне очень понравилась. НЕ как не представляю, как варить в шортах, я и у штанах умудряюсь прожигать. Специалист.
МУЖИК, яйца стальные :)
Я в шортах после десятка электродов ноги до волдырей сжёг!
Китайцы, кто их считает... Хорошо хоть маску надел
Никакой охраны труда.
Ни краг, ни одежды.
Ещё б сапоги на босу ногу надел. 😄
Зы. За изобретение - лайк
Thanks for all your ideas and application. Very nice. Greetings from Maine.
Top!!!
Se colocar uma lata com dobradiça na parte de cima para evitar as faiscas fica perfeito!!!
I really like your project I think it has a lot of potential. But the biggest thing and I see wrong and I don't know if anybody has mentioned it cuz there's a lot of stuff here that I can't read, the fact that you're welding on galvanized steel is a big No-No!!! It gives off a lot of harmful gases, when heated will kill you!!! Someone had mentioned about grinding off the galvanized before you will and you will find that you get a better Arc. I say don't even entertain the idea of welding on galvanized without the proper respiratory equipment. Other than that this is one of the best belt grinding builds and one of the easiest belt grinding builds I've seen to date great job
thanks for the concern bro, i got a respirator for welding btw.
Cool build. I'm liking it. Might give it a go. All you have to do is drink whole milk and the galvanizing poisoning will go away just like Irish potatoes on your eyes when you welder burn them. Is it bad to breathe yes, should you breathe it no, but in the event you have a sick belly and can't breathe drink some whole milk. Done it for years and I'm still here.
Shouldn't weld while the coasters are attached, the ball bearings could arc and ruin the piece. Great idea.
Great video Iv built my forge Iv got a R×R track anvil and Iv fabricated everything I need to do blade smithing. Iv been using a hand belt sander. I now know what my next built will be I'm gonna add narrow wheel pulleys as well to do detail work That's killer .Wow Bro You could build a metal lathe with that motor lol . Thats the same one used to turn Jupiter. It's a multi tap motor You can go 120 or 240 Single or 3 phase Isnt it.
Гриндер конечно хорош спору нет!!!но только сварщик в тапочках это вообще отпад!!))))без обид автор )))
Не будь занудой .он не трубу1200 под газом варит.
Тоесть чтобы сварить три железяки для собственного пользования, просто необходимо быть сварщиком? Ну тогда я универсал, а вот деньги мне платят только за дальнобой.
@@kthekeeper5117
Mo ml
Expired Deadlines он сварщик любитель и может себе позволить варить в плавках , без маски , и еще можно без защиты на болгарку . лично мне так тоже удобней особенно в жару.
Good job.Nice to see your working.👍👍👍
Welding with shorts and flip flops I like his style
Yeah that's a man, but have you seen all the comments of people complaining about it? Talking about "good job now go buy proper safety gear" bunch of sissies if you ask me. I'm not gonna spend 5 minutes putting on all my gear to run a 1inch bead. A friend of mine is always bitching at me about wearing gloves, and I always tell him the same thing, I'm like there called MAN HANDS go get you a pair.
If you ground off the galvanizing where you are going to weld, you might be surprised how much better the arc is.
Finally somebody mentions the galvanized piping. You shouldn't be welding or forging anything that contains galvanized material it gives off poisonous gases that will kill you!!! Other than that great job I look forward to seeing more from you.
i was recently welding on a yard trailer i built out of bed rails and closet shelves. i used zinc plated bolts for the axles and ground the zinc coating off. thought it might mess with the welding so i removed it. mild steel does not agree with alloys very much.
Very nice and simple design! It's amazing what can be done with an inexpensive welder and an old motor!
-Thanks for the upload!
You forgot the angle grinder, cutting blade ,steel ,clamps and electricity. Much cheaper to just buy a belt sander
What a variety of designs, and there is no limit to human thought. Like!
Why did you use 4 bearings for the tensioner wheel instead of another bicycle hub?
J DeWitt because he already used two and bikes only come with two
Should only weld galvanized in the wide open or with more protection. Like the project . Thanks
Great idea with the bicycle axels. I’m starting to build my belt grinder real soon
.com
Much respect for your project and your abilities.
Tolle Arbeit, ein unentbehrliches Werkzeug!
جون
Ein reiß und Gesichtsschutz wäre noch cool.
Great Job. Pwede ba ma weld ang washing mchine pulley na nag crack? Thanks
мне нравится как они делают чётко! а главное молча! а то наши разведут бодягу ... половину ролика выкинуть можно. лайк!!!
это точно сути с письку на морозе лишь треп
Servus, Großartig,nicht nur die Idee auch die Umsetzung. Hut ab , Meister.
This is not homemade as so many big machines are used.
these guys must have a lot of time to think this stuff up but I'm glad it's uploaded
Sir san po nyo nabili yun induction motor
That is very simple but I like so much, you make me proud.
Браво!👍👍👍👍👍👍👍 супер благодарю! Сделано профессионально🙏👍
well done. nice to see builds with cheap stuff.
как по мне станочек получился супер !!!! ну а модернизировать можно кому как нравится ... !!!!!!!!
Лотіватож
Awesome work, i like your projects. So many inspiration for my workshop. Thx, greetings from Austria
Maravilloso proyecto, justo lo que necesito 😀 fácil de hacer y muy útil, gracias.
Great job on that tool. It would be simplier to just buy one. But then you wouldn’t have nearly the fun of making it. I’m not good with angles but i absolutly love to use my wire welder. Anytime i can put all my tools to work is like therapy for me. Again great job.
Welding in shorts and sandles, Brilliant
Qoyil va omad
Savol bor edi mukun bolsa matorning kuchi haqida ayta olasizmi iltimos ... Kw va aylanish tezligi ...
Fantastic work, dude! Great new tool! 😃
Секс без границ
U tube is killing me with commercials. Hope you got paid well.
Good show.
Thank you so much bro
Perfect Work!!!!!! Vou fazer um com certeza!!!!!
Odlicno uradjeno!
Um dos melhores vídeos que eu vi com essa finalidade .
Oh god , why the Dislike Guys !! he's amazing
Those who can...do.
Those who can't critize!
@@stephengardipee5980 true )
simple tapi berkwalitas. terima kasih atas petunjukx .
Motor= 3600 rpm ou 1800 rpm, ?
Cool idea!
Great job buddy!
Belt grinder is one of my favorite tools :)
Yea buddy, useful one :)
0p
Hahahaha nice! Comments also shows support, you two are supporting each other wgen you two comment each other
Р
Б
Зачем столько сварки в глазах рябит?
galing mo ser...pede mag apprentice sau...thanks
You are my kind of welder , shorts and flip flops. Lol I wear flip flops year around and it snows where I live.
I go to work in crocs &shorts I get teased before I put my steel toes boots and pants on & I get pretty dirty and they say put some pants on when I get to work😁 job title mechanic/labor
Gary Brooks poitt
Ώω
@Keith Sargent Why the hell would they scrub him with a scrub brush?!! That's really not a good idea when trying to grow back some skin - actually it's a terrible idea!
some hot slag jump to between my toe by welding with flip flops, that's hurt so much. won't to that again with flip flops
You're a very talented person. Thank you for sharing your project. One thing I noticed. It looks like you are welding galvanized square tube. I always grind back the galvanized part before welding. Some of those welds may be questionable.
Любо глянуть! Размеры бы ещё и было б шикардос
Главное идея с велосипедными ступицами,а размеры мне кажется надо начинать с ленты если стандартная,или самому склеивать тогда всё походу на столе...
Os eixos de bicicleta aguenta o calor?
what is the revs per minute of the engine.....and,what is the minimum power to work properly..can it be 1 kw,2 kw....
Sacanagem eu paguei quase $3000 em a lixadeira compacta, vem um Áustriaco, meu pai era Áustriaco ,e faz a lixadeira top e relativamente a acessível ao bolso kkkkk parabéns pela ideia amigo,!!! Herzlichen glückwunsch zu diese idee, Danke Mein patrizier !!! 🇧🇷🇩🇪🇦🇹🇦🇹🇦🇹
This is very impressive!
Donde compraste las correas están wow soy tu fan tu trabajo es magnífico
лента таки гуляет, ннадо бочку из синей изоленты делать на регулировочном ролике и на приводном шкиву. Инфа 100%.
"Бочки" достаточно на натяжном (регулировочном) ролике, инфа 146%. :)
Без синей никуда. Пробывал черной - не тот коленкор.
Very good work hamen yah machine chahie to kaise mile belt grinder
Молодец .Золотые руки .
I would have to build the frame from wood, find an old bicycle, buy at least two belts and have the time to do it all.This is an absolutely awesome idea if you have all the stuff to do it on hand but in reality people like me that only have a few basic power tools would be have a pretty hard time building this but like i said it a ABSOLUTELY AWESOME IDEA !!! I GIVE IT THREE THUMBS UP !!!!! No i didn't say that wrong Diy'd an extra thumb using scrap cardboard and a hot glue gun... Lol Im kidding really but any ( life hack ) video that's popular these day's HAS to have cardboard and a hot glue gun.
Well said bro.
Thats awesome, but without bicycle hub also we can do it I guess. Actually, what's the main function of bicycle hub here. Can't We can do it with bearings and motors? Pls give suggestions coz I don't know the function of bicycle hub.
good idea bro,gusto ko yan,magkano yung belt sander grinder.
Great! I like so much!.
How many rpm is the engine?
I think its 2400 rpm. Not really sure.
Must c
Why didn't you make the table adjustable for angles? Might come in handy!!
Bill Woehl thats in the new and improved updated version
Yeah, thats what you call a oversized motor XD
Nice build man, helped me a lot
EXCELENTE AMIGO ,,,EXCELENTE ,,,MUY MUY BUENA , HERRAMIENTA,,saludos
Awesome project, i like it
nunca tinha visto tanta gambiarra em um video só! kkkkk
parabens amigo muito bom. tmj
أحسنت أيها المبدع . تحية لك من سوريا .
тоже люблю в тапочках и шортах сваркой варить)) пританцовывая))) иногда
Amigos muy bueno herramientas para un chapistas aver si lo puedo hacer gracias amigo Dió te bendiga
EXCELENTE VÍDEO, MUITO DIDÁTICO DICAS DE MUITA IMPORTÂNCIA PRA MIM VALEU OBRIGADO !
Tou contigo! Adorei e vou fzr uma pra mim assim!
Jaimefranca Garrido
Só acho esse motor muito bruto. mais ficou muito bom
O motor é de baixa rotação ficou muito bom.
Критиковать не буду, в комментариях замечания правильные и справедливые. Я о другом. Множество видео о гриндерах замечательные, можно брать в изготовление. Но почему-то у них подручник приварен к раме (каркасу, основанию, старине). Что резко сужает возможности станка. Неужели так тяжело для самого себя сделать его регулируемым? Даже при отсутствии материала, станок делаешь - остатки всеравно остаются. Ну хоть бы кронштейн и резьбовая пара. Совершенно непонятно...
За работу и прилежание, при всех недостатках, всеравно
РЕСПЕКТ!
👍👏🤗
motor how many revolutions per minute
Probably 1350
Parabéns cara vc é um gênio ficou ótimos 👏👏👏👏
Were you wearing long sleeves when you handled the grinder?
Looks scared....
Thank you very much for sharing information ... a wonderful and very useful product.