You can get unsealed bearings so you don't have to go through the process off taking apart and cleaning the bearings. Save time and money However, because you use the grinder on the bearings to get a sharp edge, you should leave the shield on one side to keep the metal filings from getting in the ball bearings and race. The metal filings creates flat spots on the ball bearings and will make them wear out much sooner otherwise. If using non-shielded bearings, put some grease in the bearings and use a belt sander or you can do it manually on some high grit metal wet sanding paper and just make figure 8's with the bearings until they get the proper edge on them. Using the grease and wet sand paper will keep the metal filings from getting into the ball bearings as well.
But that bearing will not go through any stress, to make things clearer. It'll be only used by hand as a guide for pulling the strings necessary of PET. But yeah, you've got a point anyways. 👍 Stay safe
@@alex1993r What are you talking about?? "sharp the bearings"??? I was saying in my first comment that you can purchase bearings without the seals, so there'd be no need for the grinder in the first place. Which would eliminate the filings getting into the bearings.
@@korishan What he´s talking about is that you have to grind down the chamfer on the outer race of the bearing, to get a sharp corner that can actually shear something. That´s what you do with the grinder.
эти подшипники выполняют в 1000 раз меньше работы, чем должны. В таком режиме их износ минимальный. Металлический порошок просто выдавится после 2-3 оборотов. Если вы будете пытаться делать это вручную - это займет у вас пару лет. Использование шлифовальной машинки с круглым диском обусловлено тем, что подшипники необходимо заточить под углом
Mount/make a sharpener/lapper so it sharpens/keeps the edges at all times. Cuts and sharpens as it goes. You’ll have to make adjustable of course. Invest in a mini-lathe as well. Few hundred bucks for a decent one. Comes in suuuuuper handy for little projects and such where you need to machine little metal parts. You can even buy/make a mount to turn it into a small rudimentary horizontal milling machine for those tough non-circular projects. Keep it up!
good video! thank you for that! I wish you a lot of success with the hobby and Healthy and friendly greetings to you and your family! (and everyone who reads too of course!) Greetings from the Netherlands! Rob
@@function3D ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran
Congratulations for the video, I thought it was great and I'm going to try to replicate it in a school project here to test, when you sharpen the 6200 bearing, is there an angle? it looks flat/straight, I didn't quite understand this sharpening scheme, would the two bearings use the same angle? Do you have a link with a photo or video showing these details of how to do it step by step to sharpen perfectly?
I am looking for a bottle cutter, I have seen several models, I have only tried the simplest with a cutter blade and washers as height supplements and it has not worked, they are not as simple as they seem to be. I want to try this one with bearings, I think that the sharpening issue is like with scissors, you only have to wear down one side, I think that without wearing down it could work but the cut would not be clean, and something that everyone warns is that maintaining the width of the the pet tape in a constant value is the secret of a good filament, here with 1 dollar I get the 2 6200's
I need to know what I need and how to put it all together and how u made everything like the gears and stuff so I can do some recycling myself. This is so cool!!! Please hit me up soon as you can 😀
I love the ingenuity. I've been enjoying the comments and how everyone has a suggestion. My question is, why make it so complicated with ball bearings when you could of just used a razor?
A knife blade dulls very quickly; These bearings are made of a very hard steel that does not dull nearly as fast. The bearing cutter works by shearing, like scissors or shears do.
Hola bro yo otra vez , Bro como haces para que la tira no suba y baje cuando corta? he tenido muchos problemas con eso y no tengo una tira consistente en toda su extension . Gracias por tu ayuda
Wow , plantie un proyecto de fabricación de filamento en mi instituto de profesorado de educación tecnológica y la verdad que además de que ya tenía la idea en mente, tu aporte me ayuda un montón !!
The base part on Prusa is different than the one in your video. Was this intentional? I can just add the area that holds the bottles in Tinkercad. Thank You 🙏
Few Questions? What is strip cut should be in mm? and Bearings, when installing on bolts, are they should be touching edge to edge or overlap should be fine?
hola como estas? estoy con un proyecto similar el Petamentor2 y tengo problemas con el afilado de los rodamientos, los paso por la moladora pero logro que corten de una pasada la botella., cualquier ayuda sirve, gracias
Sensational project, the best I've seen so far, adjusting the height of the pet was very simple, congratulations! Do you have a version for 608zz bearings (bearings for skates and skateboards), or could you make it? They are much cheaper and easier to find.
I tried it with the 608zz but I was not able to do it because they did not withstand the high speeds they reach when I sharpen them. You would need a good 608zz or another method to sharpen them that does not involve high speeds.
So is the trick to have the one bearing right to the edge of the other one and not overlapping to much? I been tring to do this for 2 weeks lol.. My bottle just runs threough the bearing and creasing the bottle..
@function3D ¡ Saludos ! Muy ¡ Buen video ! Me interesa esta herramienta. ¿ Las fábricas y vendés ? Necesito una. ¿ En qué país estás ? ¿ Precio ? ¡ Gracias !
@@diegoj.richmond428 Hola, aquí tienes este video actualizado ruclips.net/video/hEdDhRgakms/видео.html, soy de España y envío a todo el mundo, esta es mi tienda online function3d.xyz/shop/ Saludos!
First of all you are doing good i hope you are using old used bottles .. and you should do this at huge level by selling the material you are preparing and should prepare accordingly to the customer needs
Sir, many thanks to you for how to create the bottle cutter, its very helpful for me. But i can't transformed it from 6.8mm width to small width, cause im using 3d Pen, can u figure it out how to create the machine? 🙏 🙏 🙏
This depends totally on what you want to do with it. The cheapest but best for your money is the ender 3. Its usually around $200 USD (on amazon) or a little less and its a filament printer. Anycubic is having some awesome sales right now (on their website) on their resin printers which puts their cheapest one around the same price as the ender 3. I think its the Anycubic Photon 4k Resin gets higher quality with a bit less effort in the settings, but has a big difference in build plate size. Filament printers have bigger print beds whereas resin printers have really small ones.
@@untitled8513 En el culo y en el cuello puesto que la pared de la botella no entra horizontal la anchura se reduce, al igual que en las curvas intermedias que pueda tener por medio de la botella, usa mi cutter de guia de altura variable, link al video en la descripción de este, la idea es conseguir una anchura lo suficiente para que entre duro pero sin saltos de pasos del motor por la boquilla de la maquina de tal forma que las partes anchas se estiraran más que las partes estrechas compensándose e igualandose suficientemente el flujo
@@untitled8513 Tengo las descripción actualizadas desde hace meses pero RUclips no le da la gana muestrar las actualizadas, a veces pienso que no hay nadie a bordo de RUclips, ruclips.net/video/hEdDhRgakms/видео.html
Why is this channel underated. This needs to blow up.
I'll get the bomb
Tic tac tic tac chik shik shik.
Heide, that channel is very good, who knows it, they use it, sub, and likes it
But everything else is not relevant
Dont simp
Repost and it will
I can’t wait till you make millions on RUclips and upgrade that clamp. You got skills, and your channel style qualifies as therapeutic.
Love it, there's so much plastic around it always feels stupid buying more to 3d print stuff
You can get unsealed bearings so you don't have to go through the process off taking apart and cleaning the bearings. Save time and money
However, because you use the grinder on the bearings to get a sharp edge, you should leave the shield on one side to keep the metal filings from getting in the ball bearings and race. The metal filings creates flat spots on the ball bearings and will make them wear out much sooner otherwise.
If using non-shielded bearings, put some grease in the bearings and use a belt sander or you can do it manually on some high grit metal wet sanding paper and just make figure 8's with the bearings until they get the proper edge on them.
Using the grease and wet sand paper will keep the metal filings from getting into the ball bearings as well.
But that bearing will not go through any stress, to make things clearer. It'll be only used by hand as a guide for pulling the strings necessary of PET. But yeah, you've got a point anyways. 👍 Stay safe
You cant sharp the bearings without removing the shield. And also, the metal filings will get into it anyway
@@alex1993r What are you talking about?? "sharp the bearings"???
I was saying in my first comment that you can purchase bearings without the seals, so there'd be no need for the grinder in the first place. Which would eliminate the filings getting into the bearings.
@@korishan What he´s talking about is that you have to grind down the chamfer on the outer race of the bearing, to get a sharp corner that can actually shear something. That´s what you do with the grinder.
эти подшипники выполняют в 1000 раз меньше работы, чем должны. В таком режиме их износ минимальный. Металлический порошок просто выдавится после 2-3 оборотов.
Если вы будете пытаться делать это вручную - это займет у вас пару лет.
Использование шлифовальной машинки с круглым диском обусловлено тем, что подшипники необходимо заточить под углом
Glad you are posting the videos and have the list of materials I'll make one soon
Mount/make a sharpener/lapper so it sharpens/keeps the edges at all times. Cuts and sharpens as it goes. You’ll have to make adjustable of course. Invest in a mini-lathe as well. Few hundred bucks for a decent one. Comes in suuuuuper handy for little projects and such where you need to machine little metal parts. You can even buy/make a mount to turn it into a small rudimentary horizontal milling machine for those tough non-circular projects. Keep it up!
Genius
good video! thank you for that!
I wish you a lot of success with the hobby and
Healthy and friendly greetings to you and your family!
(and everyone who reads too of course!)
Greetings from the Netherlands!
Rob
This is pure gold! Thank you!
Excellent , will try myself also respect from India
Love you 💗💗💗💗💗 bro from India 🇮🇳🇮🇳🇮🇳🇮🇳🇮🇳🇮🇳🇮🇳
this man knows what hes doing
Muy buen video bien explicado a pesar de no tener audio ni estar en castellano!!!! Muchas gracias
hey nice project I also really like 3D printing and I have a question How deep did you put this screw for the bottle guide?
Exactly what I was looking for, saw one of your shorts and this got you a sub!
That's exactly how I got here! 😹👍
Guao! Muchas gracias! Esto para mí es muy interesante, voy a intentarlo, saludos desde México. ❤️
Awesome work, Congrats! Blueprint in drive is gone.
The old conundrum of needing to print parts before you have a printer…
Excellent!
What is the width of the stripe if you want to make 1.75 filament?
The width of the cut depends on the thickness of the bottle wall, as a general rule:
Thickness Width
0.2mm 10mm
0.25mm 9mm
0.3mm 8mm
0.35mm 7mm.
@@function3D ⚠️ God has said in the Quran:
🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 )
🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 )
🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 )
🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 )
🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 )
⚠️ Quran
Thank you for sharing your techniques.
Commenting for the Algo ! Great video, love your work
in your website, please, where is the electronic box cap ? missing ? thanks for your great work !!!!
Congratulations for the video, I thought it was great and I'm going to try to replicate it in a school project here to test, when you sharpen the 6200 bearing, is there an angle? it looks flat/straight, I didn't quite understand this sharpening scheme, would the two bearings use the same angle? Do you have a link with a photo or video showing these details of how to do it step by step to sharpen perfectly?
I am looking for a bottle cutter, I have seen several models, I have only tried the simplest with a cutter blade and washers as height supplements and it has not worked, they are not as simple as they seem to be.
I want to try this one with bearings, I think that the sharpening issue is like with scissors, you only have to wear down one side, I think that without wearing down it could work but the cut would not be clean, and something that everyone warns is that maintaining the width of the the pet tape in a constant value is the secret of a good filament, here with 1 dollar I get the 2 6200's
WoW nice method of cutting :)
Awesome bro thanks for sharing 💕
I need to know what I need and how to put it all together and how u made everything like the gears and stuff so I can do some recycling myself. This is so cool!!! Please hit me up soon as you can 😀
I love the ingenuity.
I've been enjoying the comments and how everyone has a suggestion.
My question is, why make it so complicated with ball bearings when you could of just used a razor?
A knife blade dulls very quickly; These bearings are made of a very hard steel that does not dull nearly as fast. The bearing cutter works by shearing, like scissors or shears do.
@@AnnaVannieuwenhuyse thank you!
Hola bro yo otra vez , Bro como haces para que la tira no suba y baje cuando corta? he tenido muchos problemas con eso y no tengo una tira consistente en toda su extension . Gracias por tu ayuda
Mantengo un ángulo por encima de la horizontal mientras estiro, eso hace que la botella se pegue a la guía en todo momento
Wow , plantie un proyecto de fabricación de filamento en mi instituto de profesorado de educación tecnológica y la verdad que además de que ya tenía la idea en mente, tu aporte me ayuda un montón !!
The base part on Prusa is different than the one in your video. Was this intentional? I can just add the area that holds the bottles in Tinkercad. Thank You 🙏
You're a legend! Thanks for sharing.
I have seen other models of platforms to mount the bearings, most of them have a guide to guide the tape and also to guide the bottle while it rotates
Few Questions? What is strip cut should be in mm? and Bearings, when installing on bolts, are they should be touching edge to edge or overlap should be fine?
The width depends on the thickness, the bearings touch each other and cut like scissors
Perfect calculation bro
hola como estas? estoy con un proyecto similar el Petamentor2 y tengo problemas con el afilado de los rodamientos, los paso por la moladora pero logro que corten de una pasada la botella., cualquier ayuda sirve, gracias
can i ask what 3d printer you use?
усовершенствованный бутылкорез адвоката Егорова))
My bearings are very tightly fitted to each other. They cut like dull scissors. any suggestions for getting the bearings sharper?
Nice cutter
Hi, I've tried but it doesn't want to cut the bottle, do you have some ideas ? thank you
the bearings need to be tightly pressed against each other
Want to know the screw size to fit the bearing can you tell?
Sensational project, the best I've seen so far, adjusting the height of the pet was very simple, congratulations!
Do you have a version for 608zz bearings (bearings for skates and skateboards), or could you make it?
They are much cheaper and easier to find.
I tried it with the 608zz but I was not able to do it because they did not withstand the high speeds they reach when I sharpen them. You would need a good 608zz or another method to sharpen them that does not involve high speeds.
I was still able to sharpen some of them by braking them while sharpening them but they did not cut the bottles well
As a machinist I am thinking of throwing them onto a surface grinder to sharpen them.
No spinning on their part at all.... and Very sharp.
Super!
Les mesures au pied a coulisse sont en mètre ou en inch?
Excelente tu video, solo que los enlaces para bajar los archivos no funcionan, podrías por favor volver a subirlos, muchísimas gracias
hi i am wondering how can it cut the bottle did you sharpen the face of the bearing thankyou
But you can see exactly what you're asking about in this video
Ваш бутылкорез самый лучший! Спасибо вам
ruclips.net/video/hEdDhRgakms/видео.htmlsi=bMiKg7kKH0l2v-fp
That's too deep for me, technically speaking. Thank youUUUU!
Does anyone among you have the list of materials...nut washer and bolt
thank you very much
do you grind both bearing or just the one? Id imagine both...
both
@@function3D what would you charge me to just make me one and ship it to me? Not lazy, physically can't make one right now. Live on Oklahoma.
Are you sanding/ grinding flat or at a angle ?
This is so cool 😊
Can I buy this gadget already made and ready to screw into a piece of wood ?
Все понятно и хорошо показано молодец.
Genius! how important is the exact bearing you use? I have a ton of 608 bearings, should that work or is the diameter important?
I use 608 bearings mate! work just as good..
Nice idea it's very good
Where can I buy such a device for recycling bottles on tape for a 3D printer
So is the trick to have the one bearing right to the edge of the other one and not overlapping to much? I been tring to do this for 2 weeks lol.. My bottle just runs threough the bearing and creasing the bottle..
The bearings must not only be sharp, but also rub together like the blades of scissors ruclips.net/video/hEdDhRgakms/видео.html
@function3D ¡ Saludos ! Muy ¡ Buen video ! Me interesa esta herramienta. ¿ Las fábricas y vendés ? Necesito una. ¿ En qué país estás ? ¿ Precio ? ¡ Gracias !
@@diegoj.richmond428 Hola, aquí tienes este video actualizado ruclips.net/video/hEdDhRgakms/видео.html, soy de España y envío a todo el mundo, esta es mi tienda online function3d.xyz/shop/ Saludos!
болты какие - на 6 или на 8 мм?
Brother, for how much do you sell these two machines
Your awesome and amazing. Thank you for the channel
¿Puedes volver a poner los stl para imprimir por favor?
Gracias.
puedes pasar el archivo modificado?
el del video es distinto al que publicastes, usa la parte donde va un tornillo para la barilla
Hello. Thank you for sharing your projects. You can lay out the latest model of the bottle cutter. With a part for the guiding bottle.
Link in the description
Thank you for sharing this 🙏🏻🙏🏻✌🏻✌🏻
Больше видео ,у тебя хорошо 👍 получается
Ендер3
Solo se puede sacar un solo tamaño de hilo?
First of all you are doing good i hope you are using old used bottles .. and you should do this at huge level by selling the material you are preparing and should prepare accordingly to the customer needs
I use my used bottles
Nice job 👍💞
Would LOVE to know what you used to clean out those ball bearings.
Ive always used brake cleaner.
Grease (subtitles)
Aseton
Great 👍 can you share of technician details?
Sir, many thanks to you for how to create the bottle cutter, its very helpful for me. But i can't transformed it from 6.8mm width to small width, cause im using 3d Pen, can u figure it out how to create the machine? 🙏 🙏 🙏
What to do with those strips ?!
Olá, tudo bem, você fornece este desenho para imprimir em 3D?
yo, did you really use a grinding disc to cut that bolt on purpose?
ruclips.net/video/hEdDhRgakms/видео.htmlsi=HRbp-2xx4VJN4jRF
@@function3D lol okay then
Could I ask for a stl file to define the bearings for the cutting tool. I don't know which one it is. Because my ENG is weak. Thanks
Updated video, see description ruclips.net/video/hEdDhRgakms/видео.html
I have already printed the first type, so I need the cover for the bearing
I’m confused ~ but section is actually cutting the bottle 🤷🏾♀️ ~ genus idea ~ I just don’t understand how it works!
Anyone has the problem of the stripes getting wider? Help me please. Thank you.
plz provide me the exact stl file shown in video
Как часто затачиваете подшипники?
Never
Good idea !!! Where can you buy a complete set assembled? What is the price?
Etsy. About 50$
Thank you
Do you sell these?
What 3d printer would you recommend to someone just getting started?
This depends totally on what you want to do with it. The cheapest but best for your money is the ender 3. Its usually around $200 USD (on amazon) or a little less and its a filament printer. Anycubic is having some awesome sales right now (on their website) on their resin printers which puts their cheapest one around the same price as the ender 3. I think its the Anycubic Photon 4k
Resin gets higher quality with a bit less effort in the settings, but has a big difference in build plate size. Filament printers have bigger print beds whereas resin printers have really small ones.
Dude, can we just buy it directly?
Hi bro
How wide is the pet bottle yarn?
function3d.xyz/en/?Display_FAQ=267
Deixa o link para download
So nice
I want one of these
Which bearing is used
github.com/function3d/petalot/blob/master/BOM.md
Thank you
muy buena esta máquina de cortar .debería patentizarla para venderlo a quien quiera comprartelo
Is there a place I can see this being made
Go to description arrow,at bottom is transcript, all is there
tengo problemas haciendo las tiras. nunca me salen de una misma medida de un lado mide ciertos mm y mas adelante cambia, que estare haciendo mal
@@untitled8513 En el culo y en el cuello puesto que la pared de la botella no entra horizontal la anchura se reduce, al igual que en las curvas intermedias que pueda tener por medio de la botella, usa mi cutter de guia de altura variable, link al video en la descripción de este, la idea es conseguir una anchura lo suficiente para que entre duro pero sin saltos de pasos del motor por la boquilla de la maquina de tal forma que las partes anchas se estiraran más que las partes estrechas compensándose e igualandose suficientemente el flujo
@@function3D estan caidos loss links
@@untitled8513 Tengo las descripción actualizadas desde hace meses pero RUclips no le da la gana muestrar las actualizadas, a veces pienso que no hay nadie a bordo de RUclips, ruclips.net/video/hEdDhRgakms/видео.html
Terlalu kreatif 🔥
How much does this machine cost?
what is the blue chemical, is it isopropyl alcohol
Solvent to remove the glue from the label
It’s essentially the same concept as scissors, but spinny
Bearing size?
ruclips.net/video/hEdDhRgakms/видео.html
Eres realmente genial.
my want to keep tiny bit of oil on the berings
ruclips.net/video/hEdDhRgakms/видео.htmlsi=cKZ2HpLfq-jsXYvP