I have this same case. Will be learning how to install my RGB fans for the first time, so it was helpful to see how you took off the front panel and then routed the fan cables through the side vent holes of the front of the case. I wish you would have shown a slower version of the video though.
Just bought this case, I got the rgb add model with a PSU shroud and 3 pre installed RGB fans, Your video has been a great help so far with trying to figure out wire management, I even have the same Motherboard as yours, Kinda cool to see how your's looks before starting mine, Thanks for the vid
i have the same case, and yeah, cable management for this case isn't very good. only way to make it "least neat" is to run them in betweet the holes and just strap them there using wires, hehe...but the front panel, i didn't know it could be taken off just by pulling from the bottom 😶
one of the weakest part on this case was the cable management, it needs a lot of work. But the new matrexx versions has the Shroud and other features at the back that addresses the cable management issue.
Hi, bought the one with no fans and im planning to install 6. Now im confuse on how to use/install the built in led lights together with new fans. Any guide on this?
The led lights on the front panel also have a rgb cable that you connect together with the fans. You need to use the splitters included on the fans you bought either rf120 or cf120, other than Deepcool's own fans you can sync or connect the led in the front to other brands.
labeled as main in? not sure if there are those kind of case cables the only ones i have here is the power,. hdd led, reset sw, + & -, hd audio and usb
oh the rgb strip, you can either connect it to the rgb button on the case as well and better get an rf 120 fans also so you can sync all of them either via motherboard 12v header or rgb button. You will see a 4 pin connector there as well as a molex connector
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Thank you for showing me how to remove the front panel... worked like a charm.
Is it difficult to reattach?
@@NW3000 No not really, just a pain to open
@@cupcake_seiko2645 cheers
I have this same case. Will be learning how to install my RGB fans for the first time, so it was helpful to see how you took off the front panel and then routed the fan cables through the side vent holes of the front of the case. I wish you would have shown a slower version of the video though.
I will try to do a follow up video on that since a lot of people are asking me that question as well. thank you for your feedback!
Just bought this case, I got the rgb add model with a PSU shroud and 3 pre installed RGB fans, Your video has been a great help so far with trying to figure out wire management, I even have the same Motherboard as yours, Kinda cool to see how your's looks before starting mine, Thanks for the vid
I am trying to install some fans at the moment but I can't take the front panel of
Same
Grab the bottom part and you can feel a hollow point or something then pull it
I did it, you just have to pull hard from the bottom, it pops out hard!
Host Sub yeah I did and I’m pretty damn sure I broke a couple things holding it in place
i have the same case, and yeah, cable management for this case isn't very good. only way to make it "least neat" is to run them in betweet the holes and just strap them there using wires, hehe...but the front panel, i didn't know it could be taken off just by pulling from the bottom 😶
How did you take the front panel of?
.
I did it, you just have to pull hard from the bottom, it pops out hard!
Got this case and love it but holy shit the cable management was a nightmare lol
I need help I am so confused with the wiring for the fans and rgb strip pls help me
one of the weakest part on this case was the cable management, it needs a lot of work. But the new matrexx versions has the Shroud and other features at the back that addresses the cable management issue.
Love the video po, Gawa po ulit sana kayo ng new para sa pagiinstall naman ng cf120 or rf120 slower version po. Thanks
How did you connect cf120 fans in a rgb header with 4 pin (cf120 fans has 3 pins)
I use 2 different splitters. 1 for 4 pin and 1 for 3 pin
Question how did you remove the front panel?
Same issue. Did u ever find out how to remove the front panel
From what I've seen, you pull the bottom of the front panel and it should come off. Most likely have to take off both panels.
There are little tabs on the side and u push them out
Im trying to install a fan on the lower part on the front and I can’t because of the hard drive thing.
You nees to use the long screws included on the case. The screws are similar to the screws used in an AIO
Hi, bought the one with no fans and im planning to install 6. Now im confuse on how to use/install the built in led lights together with new fans. Any guide on this?
The led lights on the front panel also have a rgb cable that you connect together with the fans. You need to use the splitters included on the fans you bought either rf120 or cf120, other than Deepcool's own fans you can sync or connect the led in the front to other brands.
@@WMDTech Thanks!
How do you plug the case cables labeled main in?
labeled as main in? not sure if there are those kind of case cables the only ones i have here is the power,. hdd led, reset sw, + & -, hd audio and usb
@@WMDTech its the wires for the rgb strip thats on the front of the case
oh the rgb strip, you can either connect it to the rgb button on the case as well and better get an rf 120 fans also so you can sync all of them either via motherboard 12v header or rgb button. You will see a 4 pin connector there as well as a molex connector
WMD Tech where on the motherboard
For what is the cable with "MAIN" on it?
Same problem idk
I can’t pull up the panel its so tight. Please help me
You need to pull it upwards from the bottom area of the front panel, there's a lock so you need to put some force on it
How to remove the side panel ??
side or front? side you will just unscrew all four screws
@@WMDTech the one without the glass i just cant get it out
@@l1m1t80 unscrew the two thumb screws at back (or use screwdriver) then slide it backwards and it should come off
They release model with psu shroud.
yes they recently released a version with PSU shroud, that case will be coming on wmd tech soon!
Have same case and mine has PSU shroud lol, no ssd tutorial bummer
Does it support m-atx
yes
KFC ofc
Gpu installation was a pain in the ass
How do you do it?
Halos same ng Fractal Focus G mas spacious nga lang to' and mas affordable btw nice review!!
Havent seen Fractal Focus G but yes super spacious nito kahit compact case sya and mas ok ung airflow never mo mararamdaman ung init sa TG side panel
sir pano nyo po direktang nakabit yung sa ssd sa may cable management area sir
i-screw mo lang sya on the opposite side
@@WMDTech ah okay po thank you sir
120mm po ba yung fan sa front panel?
yes
Pano niyo natnggal yung front panel sir
Sa ilalim mo hahatakin. Meron syang space sa ilalim
@@WMDTech salamat sir natakot kasi ako pwersqhin sobrang higpit kasi
Ginamit nyo ein ba yung built in na rgb controller na nasa likod ng front panel
pwede mo naman buksan muna then meron syang mga clip sa likod ng front panel? yun pde mo pisilin un para umusli ung front panel
RGB IS ❤❤
san niyo po nabile?
Available na sya sa mga retailers pero sa PC hub pa lang ung merong exact price.
Konting ipon pa mabibili ko na din to
super solid case haha sayang hirap lang ng cable management at PSU shroud
WMD Tech thanks for the info
video is too dark and cannot see anything bro
yeah sorry for that, you can watch the newer video matrexx 55.
Too much rgb.