@@Nathan1975Liggy check in circuit diagram a 220 ohms resistor is connected to the Anode of Red Led while the Led Cathode pin is connected to the collector pin of the transistor but when soldering, the resistor position is changed with red Led position, one side of the 220 ohms resistor is connected to the collector of an NPN transistor (BC 547).maybe this change in positios between Led per diagram and resistor vs practical soldering explains why Led is always ON. I haven't tested the circuit yet but if I am going to test it then I will do it per soldering not per diagram. Maybe the author can tell us more ,by the way ,I'm not an expert in this area ,I do some innovations and therefore have to learn constantly and pay attention to every detail before I try anything
Otherwise, congrats Tech ideas, it is great, simple and working perfectly. The only thing you could possibly check again is difference between the circuit diagram and actual soldering on positios of Red Led and a 220ohms resistor
I built the circuit as the video instructed and as the suggestion to change the direction of photodiode/dark LED and I am still unable to get it to work as in the video. Help please.
Drone doubt. One thing is not clear in this video (f450 video ) . ESC without BEC. 1. First doubt if we buy all 4 esc with bec or just one? 2. Not clear if the if the external voltage regulator (BEC) is connected to all ESC or just one. Because in f450, we solder all 4 ESC, and I couldn't see how it connected, to where /which component etc 3. If all 4 ESC have built in BEC, should we disable it? Should the red wire removed and only data & negative wire is connected to the flight control board? I saw something like that somewhere. So Please clarify..
@@BinuJasim maybe the person who asked the question was not clear. When he/she asked if the the circuit can work at night and daylight , probably the circuit was understood as being a light sensor while it is actually a proximity sensor,or the person wanted to know if the circuit is not affected by the sunlight, of course these IR device s are prone to sunlight. Otherwise Tech ideas deserves a credit for a good work, he has shown a way our task is to congratulate him and if possible improve it in terms of the range it can detect, other applications etc
Why is the place of red led different between actual building and circuit diagram? In the circuit, red led is between the collector and 220 ohm while in actual setup it's found connecting between 220ohm and photo diode. Curious to know which is correct, pls.
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
WOW! Nice photo work, nice jig that holds transistors, etc. Nice simplicity. quick and simple!
Thank you
Awesome bro i was searching how to make simplest and i found you the best thanku very much for this idea keep it up 😃😃👍👍👍👍🙏🙏
I have never found something like this! I will rebuild it!!! 👌👍
It’s so easy to build
Very good presentation. Thanks a lot!
I did and led is always on?? Can you please help me🙏
same here mate. found 2 circuits on RUclips now one uses an LM358 OpAmp and that was the same. both circuits the LED is permanently on
@@Nathan1975Liggy check in circuit diagram a 220 ohms resistor is connected to the Anode of Red Led while the Led Cathode pin is connected to the collector pin of the transistor but when soldering, the resistor position is changed with red Led position, one side of the 220 ohms resistor is connected to the collector of an NPN transistor (BC 547).maybe this change in positios between Led per diagram and resistor vs practical soldering explains why Led is always ON. I haven't tested the circuit yet but if I am going to test it then I will do it per soldering not per diagram. Maybe the author can tell us more ,by the way ,I'm not an expert in this area ,I do some innovations and therefore have to learn constantly and pay attention to every detail before I try anything
Otherwise, congrats Tech ideas, it is great, simple and working perfectly. The only thing you could possibly check again is difference between the circuit diagram and actual soldering on positios of Red Led and a 220ohms resistor
Can I use an infra red receiver instead of a photodiode? I m from Malaysia.
Yes, of course you can use ir receiver to it
1:39 which resistor you used please reply fast
100 ohm
Tq tq tq so much 👏👏👏👏
Thanks sir for this project 😱😱🤐😍😍😍👍👍👌👌👌👌👌🤘🤘🤘🤘
Welcome
My circuit is made in exactly the same way but my LED is always on . How can I fix it?
Fixed the circuit , photodiode is incorrectly biased in video , make sure to connect shorter side to transistor
I built the circuit as the video instructed and as the suggestion to change the direction of photodiode/dark LED and I am still unable to get it to work as in the video. Help please.
What kind of photodiode is this one?
Can we use it with 9v battery output
Yes, you can use it
@@TechIdeasAG what is range of sensor
Wow, very simple and useful. excellent non speak education. great thank for you.
Can i using mosfet rfp30n06le ?
Any transistor Or only u mentioned transistor
Mere pas D965 he
It will also work, just follow the pinout
Is it long lasting? How can I use 12 volt solenoid valve in place of led light?
Great no need for OP 👍
Where is out?
Great 👍🏼 video.......Can use buzzer instead ...... different sound intensity determines by the distance of the obstacle??
Você conseguiu fazer com a campainha ?
Drone doubt.
One thing is not clear in this video (f450 video ) . ESC without BEC. 1. First doubt if we buy all 4 esc with bec or just one?
2. Not clear if the if the external voltage regulator (BEC) is connected to all ESC or just one. Because in f450, we solder all 4 ESC, and I couldn't see how it connected, to where /which component etc
3. If all 4 ESC have built in BEC, should we disable it? Should the red wire removed and only data & negative wire is connected to the flight control board? I saw something like that somewhere. So Please clarify..
Awsome bro
Muy buena idea
Wow.... great..... well-done
Wow nice.. Excellent for my mini project. A big thank you from me for uploading this video.. Thank you....
Is that save when i'm using 12v input?
Can I use 9V battery instead of 3.7 V battery please reply urgent sir
Your circuit worked
Can we add buzzer
Which one - n + in inrared n photo diode sir?
Short lead is negative
@@TechIdeasAG for both of 2 parts right? Tx u sir god bless u
with this can a metal detector be made?
Great project
Sir ye bataiye ki isko hum 5v se chala sakte hai
Yes, you can
Neither of led may we control dc motor in this
Which is the out pin of this sensor??
Of course, the collector of the bc547
Does it work only in the dark? Or on daylight too? Sry for my english
Yes, it'll work on daylight also
Thx:)
@@TechIdeasAG Don't talk if you don't know. IR receiver will turn on in sunlight.
@@BinuJasim maybe the person who asked the question was not clear. When he/she asked if the the circuit can work at night and daylight , probably the circuit was understood as being a light sensor while it is actually a proximity sensor,or the person wanted to know if the circuit is not affected by the sunlight, of course these IR device s are prone to sunlight. Otherwise Tech ideas deserves a credit for a good work, he has shown a way our task is to congratulate him and if possible improve it in terms of the range it can detect, other applications etc
Hi can a 9v battery be used on this instead of an 18650?
How did it go?
Can I use IR LED receiver yes are no plz response 😭
Yes, you can
My led is always on is there any problem with this
Nice Job. Thanks for sharing. ;-)
That circuit is going to have serious problems with interference.
Yes, and there is an application for it.
Wow nice
what is ir led
Infra Red LED
Can i use this circuit for my car as a parking sensor.
Please reply brother..........
What's the function of infrared?
will this work as a water level sensor ?
Can i use 9v battery
Is that capacitive or inductive sensor
No, this is IR proximity sensor
100 om or 220 oms ki regist kitne watt ki leni he ..1 watts 1/2 watts
Hi..i love ur videos...plzzz make a simple solar tracker circuit for the 12V DC motor on the solar panel stand..
Incredible!!
How much power supply we can give
Sound is very high.
I don't quite understand how it works :\
Informative sobra ty
Thank you
I have a doubt can we use infra red light incase of photo diode??????
Pls reply fast, genius
Yes, it will also work
Can i to use with a bomb of water? For a dispenser....
It is not working 😞 plz help
I soldered how did you show that I follow of soldering wire
Simple home detector for cockroaches or mouses. :)
V nice
i need your help vaya
Ok
@@TechIdeasAG vaya apnar sathe kotha bolte chay ami
bolben please
Nice😃
Is it fake?. I did and led always on
I found ur circuit problem and sensor ok now
Wt the problem
Why is the place of red led different between actual building and circuit diagram? In the circuit, red led is between the collector and 220 ohm while in actual setup it's found connecting between 220ohm and photo diode. Curious to know which is correct, pls.
@@mgmg-nr2dj i don't remember now which one problem photo diode or ir led.i just remember he showed wrong + -
GharGhnti ni pcb vidiyo banavoji
Can you please make that on breadboard
Bc548?
Ok
Not working
Mal porque corta el vídeo ya que el LED se queda encendido hay que agregar otra resistencia
Publicité trop longue : je coupe et je ne reviendrai pas.
photo diode ka no.kya h
Класс , молодец!
Yhanks
It detect not your left hand?
on trans on induktor on led ...
Nice but
We prefer arduino this days
genial
Bhai saman nahi mil raha
Zajebiste! Super
Why ird
Meka weda nene
Bc 547 nahi milta
Bhai bc547 and bc548 same npn transistor hain aur Yeh kisi bhi electronics ki soap par mil jate hain