superbly explained Sir, good job! I had an IR module , I attached a 5 vmotor pump to it using a TIP32C transistor, Output from module is attached to base of transistor, VCC 5v from power source & module to the Emitter & positive line from pump to collector, when the current is switched on it makes the pump to run continously , It , however slows down when an obstacle is brought near the IR transmitter / Photodiode, is there something wrong with the IR module? I was trying to make an automatic soap dispenser
I found the solution to the problem, I realized there are two types of IR module in the market , one with single LED which works well with BC 457 transistor , as shown in your schematics & other with Two indicator LEDS, which works well with TIP32C /TIP 42c
Yes this circuit works, I made it 😍 first ir circuit which worked for me out of 3. If anyone want proof or photos then mention in reply to this comment. Will be Happy to Help You 😊
By using flipflop & relay, you can control any appliances... IR module > flipflop > relay > appliances This video can help you... ruclips.net/video/Wb3vgjZTksA/видео.html
It is not about colour... It is Infrared rays... Black colour fully absorbed IR rays.. Other colours may partially absorb/reflect. White colour fully Reflect IR rays
When you connect a 5v relay to this IR proximity sensor, which transistor is used, PNP/NPN? Or its output can be connected directly to the relay?? Kindly reply..
Sir ac non tuch testor aisa banye jo 5 miters dur se hi indicket karne lage sir kheto me achanak 230 volt tar gira rahata hai jo hame 5 bar Mar chuki hai sir please 2 din me banaye
When connecting the pump this circuit it continually on or when we move any object near to sensor then pump stop working otherwise it continue working Any suggestions how to solve this problem
TV remote controlled home appliances - real time.. ruclips.net/video/MX3e3i53HhY/видео.html This is our another RUclips channel.. Soon this video upload in this channel as DIY video.. If you are interested, watch this video Thankyou..
@@SDevElectronics Can ne555 timer relay module be used for OFF delay also > for both activating the load and hold/maintain its ON position up to specified time (0-10 sec) ? in a IR sensor +ve output circuit ? triggering on off again and again by IR sensor output ? as I am annoyed by the on off flickering Output of IR sensor relay circuit and its sound while using it as automatic sink/basin hand wash process, as hands sometimes goes way from IR leds.
Make sure your connecting right terminals of photodiode. Put multimeter at terminal 3, the voltage at that point should vary... Even everything is right. It may take some time to work perfectly..
Agar humko IR Sensor se ek distance pe ane ke baad AC wale switch ko band karna ho tho Jaise rise ka taba full hua hoga tho machine band karni ho tho kar paynge?
You are genius.
Hi SDev Electronics, I made my own IR Sensor and it works, thanks for the tutorial and for the diagram.
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html....
Is working in sunlight .? Please reply
Gutes Video, ich verwende 2 Sensoren für einen Bahnübergang auf der Modelleisenbahn Spur z
GRACIAS POR TU APORTE MUY VUENO
VERY GOOD IDEA THANK YOU FOR KNOWLEDGE SIR YOU ARE GREAT THANK YOU AGAIN HARE KARISHNA
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html...
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html. ..
superbly explained Sir, good job! I had an IR module , I attached a 5 vmotor pump to it using a TIP32C transistor, Output from module is attached to base of transistor, VCC 5v from power source & module to the Emitter & positive line from pump to collector, when the current is switched on it makes the pump to run continously , It , however slows down when an obstacle is brought near the IR transmitter / Photodiode, is there something wrong with the IR module? I was trying to make an automatic soap dispenser
I found the solution to the problem, I realized there are two types of IR module in the market , one with single LED which works well with BC 457 transistor , as shown in your schematics & other with Two indicator LEDS, which works well with TIP32C /TIP 42c
Same problem
Have you got solution
very good project friend
Yes this circuit works, I made it 😍 first ir circuit which worked for me out of 3. If anyone want proof or photos then mention in reply to this comment. Will be Happy to Help You 😊
Hey please shed some light
@@praneethk3554 What problem are you facing?
Need help the pot of my sensor needs to be adjusted frequently because it suddenly turns on even there's nothing coming close to the sensor.
Why do I have to calibrate the pot always
Are you using it in sunlight or a place where sunlight available very brightly?
Will it work in sunlight for sanitizer purposes?
Can use outdoor?
In outdoor: cover both LED.
Sunlight can emit ir rays, our module may disturb
Can you make it as a switch for other electronic devices?
By using flipflop & relay, you can control any appliances...
IR module > flipflop > relay > appliances
This video can help you...
ruclips.net/video/Wb3vgjZTksA/видео.html
Thanks
hi.. can I use it 10~30v?
Can I use it as a photoelectric eye mark sensor in packing machine for sense print mark on plastic sheet.
Nice !!!
Bro can we put it in the 24v adapter bro
No 5V is recommended...
Put 5V regulators
will it only work on white color or any object works except black?
It is not about colour...
It is Infrared rays...
Black colour fully absorbed IR rays..
Other colours may partially absorb/reflect.
White colour fully Reflect IR rays
Will it work in sunlight
Reply me plz
Yes
Can i use more ir pair instead of 1 ir pair so circuit is working or not ?
Can this proximity sensor works by connecting in a microprocessor giving a input?
Yes
ruclips.net/video/jCOES2n3jV4/видео.html
@@SDevElectronics contact number
nice project
Can I use lm393 IC , it is open collector so would pull up
Sir is using male header necessary
Can i use simple wire in place of male header?
Sir please answer fast i have to submit my project next week
Header not necessary.
You can use wires..
It's up to your wish
Hi can I use 4558D
Is that a PCB?... Can I use a breadboard in place?
I used dot matrix PCB. You can use breadboard
Can I put a a buzzer instead of led
Sure you can replace led..
Will Dc motor works from this sensor
Yes can,
Use it with Transistor or relay
good for making missle
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html...
Can we extent the length of IR bulb 💡?to place bulb only to visible
Is it use ir 3 pin receiver sensor
No I'm using photodiode.
You can also 3 pin it receiver...
*Can i use the led from remote*
*as the transmitter and reciever?*
*how to make a reciever?*
ruclips.net/video/uorlMHaoP9c/видео.html
When you connect a 5v relay to this
IR proximity sensor, which transistor is used, PNP/NPN? Or its output can be connected directly to the relay?? Kindly reply..
Bomb squad music❣️
What do you used to give
vcc and ground supply
I used my mobile charger +5V 1A
Can you Please tell me what is the name of Device u Used to connect THE IR MODULE WITH THE BATTERY...?????
I used my mobile charger for 5v supply
How u did the soldering?
Refer circuit diagram, inside the video
@@SDevElectronics thanks
Can this sensor work in direct sun light?
Yes, Sun will emit IR rays
SDev Electronics As sun emits ir rays, sensor will be void?
Hello sir .....10k pot or 100k pot?
Maximum hum kitni distance bada sakte h.
10cm max for me. It works on the principle of reflection.
More Light, More reflection, More distance
Can I used 9 v battery
Yes you can use 9V...
Better use 7805 regulator.
Ok.. but i don't know the accories name... what was used...
Components used is shown in this video...
This is 12v possible
Sure but use proper resistor values
how much value Photodiode
5mm photodiode
How much value IR sensor
Hi sir.... How to soldring this circuit
can reflect by human skin
Yes, can reflect..
Can control the sensitivity with preset
sir can it sense upto 1m? what is the maximum distance that can be sensed?
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html....
Sir ac non tuch testor aisa banye jo 5 miters dur se hi indicket karne lage sir kheto me achanak 230 volt tar gira rahata hai jo hame 5 bar Mar chuki hai sir please 2 din me banaye
Please texts in English
How much meter it can detect
Not metres, few centimetres only
But if we requiere enhance distance what should we do?
Output voltage?
5V
Sir relay kaise connect kare aur kon sa relay model number ka
Comment in English Please...
Bhai jan register ki value to app batata ho lakin is ka watt nahi batata ho ka lint watt ki ha 1/4 ya 1/2ya 1 watt ki thank
When connecting the pump this circuit it continually on or when we move any object near to sensor then pump stop working otherwise it continue working
Any suggestions how to solve this problem
I think you may use relay...
Relay may be in reverse logic,
Use opposite logic relay
Same problem
Not using relay
How to create a speed breaker alarm, around 40-50 feet distance
Output voltage kitni rahegi iski
5V
Where can we get these components??
All these components are found in nearby Electronics shop below ₹40.
Or search it in online
Can u pls send the link
Search in this website
nevonexpress.com/ or Amazon
How do i alter it to make it detect black instead of
It misbehaves on sunny days whats the remedy for that
Cover photodiode & IR LED with insulation tape separately
Please make a video on how to control our lights and fans with our mobile. Arduino Uno project with 4 relay channel. Please please🙏🏼🙏🏻🙏🙏🏽🙏🏾🙏🏿
TV remote controlled home appliances - real time..
ruclips.net/video/MX3e3i53HhY/видео.html
This is our another RUclips channel..
Soon this video upload in this channel as DIY video..
If you are interested, watch this video Thankyou..
@@SDevElectronics Can ne555 timer relay module be used for OFF delay also > for both activating the load and hold/maintain its ON position up to specified time (0-10 sec) ? in a IR sensor +ve output circuit ? triggering on off again and again by IR sensor output ?
as I am annoyed by the on off flickering Output of IR sensor relay circuit and its sound while using it as automatic sink/basin hand wash process, as hands sometimes goes way from IR leds.
can we use this to measure heart beat
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html👍👍👍👍
How can connect servo
How to include 4 sensors in series in one circuit for 4 outputs.
Can u send circuit diagram ?
Check Inside the video ..
How much it costs you
Below ₹30
Bro can you please upload the circuit diagram for my help
can you share PCB layout file?
I don't have that?
Make your own from circuit diagram..
@@SDevElectronics obviously i will...just asking in case you have
Ok. 👍👍👍
"Thank GOD", and thank you very much for your support and time 😉 What is the MAXIMUM distance you have tested this device 🤔
15cm
@@SDevElectronics Thank You, is there a way to increase this distance 🤔
It works based on the principle, Reflection of Light...
More brighter light, more distance..
Note: we can't see IR rays through naked eye
@@SDevElectronics "Thank You", thank you very much 👍
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html...
I tried to make it but it didnt work plzz help me
Make sure your connecting right terminals of photodiode.
Put multimeter at terminal 3, the voltage at that point should vary...
Even everything is right. It may take some time to work perfectly..
How can you run 5v water pump on this ir module
You can control Water pump with Relay module
5v- to 5v power supply
GND - to GND
IR OUT - to RELAY INPUT
Agar humko IR Sensor se ek distance pe ane ke baad AC wale switch ko band karna ho tho
Jaise rise ka taba full hua hoga tho machine band karni ho tho kar paynge?
Yes only we have to use relay
Sir TIP 32 kaise conect kare
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html..
How much AMPEARE is required for this circuit
Not yet tested...Max 50mA to 100mA including LED
Mena bhi tray Kara nhi ho rh
2:24 omg
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html....
Sir, I made it but not work
In this video, I tested it with Multimeter
ruclips.net/video/WeI67jCpIAE/видео.html
Sacchi me kam kere ga na ???
Please send back side diagram
Circuit Diagram inside the Video
I need 12 volt output
Where is the schematic digram??
Inside the video...
sir diagram
Circuit diagram @ 1:53
Metal touch sensor alarm anyone explain
Please subscribe , like and share this vedio
ruclips.net/video/5ipIDWnuaDM/видео.html....
Bhai photo diode ka num kya h
bro please send me the back soldering portion
muje ye component kaha milenge
Iska ckt diagram de Diya Kare sir
Bahi sahab nail tou cut karr lou phelay
Jaani ye chaku hai...lag jay to khoon nikal aata hai
Excelente, pero córtate las uñas, se ve muy feo eso.
Thanks for your feedback and good suggestion..
But I (also most Electronics persons) use nails for cutting, sleeving wires and to open Mobile phones.
Sir where is test pin or where do we can connect the logic toggle pin
Apney app hi bnale
Btaya toh h ni kaisey bnaeyngey aisey toh khud hi bna lete
Our support is always with you.
shorturl.at/izES5
abe thik se toh btata bolkr, song kyi daal diya
Bhai apnea phone number send kare do
That nails
Bro how to solder the wire in this module
You can use PCB Female connectors