Если взялся за дело доводит его до конца. В твоём случае станок должен был что либо просверлить. А тут как он был сломан таким и остался. Доделай его до работоспомобного состояния и будет тебе лайк
I applaud the job you did especially with so few power tool, it a good restoration. However please bolt down your vise, it's a beautiful bit of kit and deserves a permanent place of honour.
Do you applaud the fact that the machine was painted ? is this called restoration? This is a good machine, if it is restored, it will be able to serve for a very long time and help in the work ! but after such a restoration it is not a machine but just a useless twister with a beating spindle and a non-working cartridge !!! In our country, for such work, THEY are FIRED immediately !!!!
Мне вот так у всех под кустом свирлика воляиться ? И покраска проста божественна!! Но самое главное где станина и мотор? Или он от вечного двигателя работает? И как прекрасно бить по болту с резьбой молотком. Если-бы мне поймали на преждней работе за таким то руки отрывали с совсем корними
You should have put the first one of those bearings that went on the top of the quill drive in first then inserted the second. That would have kept their spacing.
Temporary? No room on the bench? Drill a couple of holes through the bench top, secure the vise to the top with two or three heavy bolts, washers and wing nuts. When you’re done, spin the wing nuts off, remove the bolts and store the vise. The holes in the bench could be used with dogs for planning or sanding...simple. No excuse for turning a vise into a weapon.
LMAO I thought I was the only one calling BS on these videos. "I mean, I was mindin me own binuss and what do I's find!?!" Every video and their not the only ones who do it. Seriously, we don't need some story for the hunk of crap ... we just want to watch it get restored lol.
@@0420Junket I like the people who say: "I picked this up for ten euros/dollars at a scrap yard" or "someone was cleaning out an old storage shed and find this in the back" or something like that. I do not believe "my videographer was filming me when I found this piece of industrial machinery lying by the side of the road."
@@Ambidexter143 lol exactly. “This person with the camera goes everywhere with me. When finding tools, going the store or even taking a dump ... their there .” Lmao
Very good restoration. You have demonstrated how much can be accomplished with hand tools and labor. Will the second part of the video include installing a motor? Good job!
Hey great job mate , it is good to see the old gear being restored and looked after . Mate I have a question for you , can you tell me what those two extra belt pulley cogs on the side of the drill press are there for and what do they do as I have never seen that set-up on a drill press before . Also where does the electric motor go on the drill press . I hope this finds you doing another resto and I hope I am not bothering you with these questions .
I think some people have lost sight of the purpose of the video's it doesn't make ant differance how you come by the unit, as long as you have fun fixing and watching.
It's thrown away not so long ago. Didn't rusted too much. No bolts unscrewing with acetylene torch. I think it's not even meets rain before you found it)
For the record, I've done this type of rebuild a few times. doing a BOISE CRANE 1800 at this time. Judging by some of the comments, I'm inclined to think this must be "open Sunday" in the lounge at the local sanitarium !! :)
@@TOP19809 там шариковый упорный подшипник стоит, его тяжело найти, автор решил не парится. Да и посадки подшипников все стандартные, там конкретно просажен вал..
Рукожоп! Так испоганить добрый станок, который можно было бы привести в порядок. Сборка подшипников - шпинделя и втулки - в учебник ляпов при сборке. Браво!
I'm not sure that this was an "actual find". But I do know that the puppy was a cutie. Did it work after all that restoration ? I didn't see the on / off switch replaced with the wiring.
Hello, in today's video we will restore a drill press that I bought at a yard sale and clumsily threw in some bushes and covered up with a couple of sticks.......
Yes, I don’t buy the ‘find’. There is virtually no corrosion and everything is so well lubricated it comes apart with ease and no heat. The chuck and arbor were not there at the ‘find’ then they are mysteriously in the quill, then they disappear again before re-emerging. Would have liked to see a minimal protective coating or lubrication on mating and sliding surfaces during re-assembly. But still fascinating enough to watch to the end. Thanks for posting.
Вы зачем вытащили станок из гаража. Открутили площадку. Положили его под дерево и закидали ветками, а потом включили камеру и сделали вид, что он там до вас лежал. Такого не бывает!
Радиально упорные подшипники собираются не запресовыванием а внутренняя обойма вставляется под углом к наружней и с проворотом. Для шлицевых гаек существует специальный ключ а не пробойник.
Not impressed . The main shaft looked buckled when it was spun towards the end of the video and who in their right mind would re-use old worn woodruff keys and that old chuck. Filing new gear teeth on that massively abused chuck was the point where I lost faith in the restoration and couldn’t take it serious any longer. Why is it these “restorers” believe that the more metal you remove , the closer to manufacturing tolerance the part becomes???
![I build mini BENCH DRILL / Construyo mini TALADRO de mesa [1a Parte]](http://i.ytimg.com/vi/3s2Y73Kk9BI/mqdefault.jpg)
![I build mini BENCH DRILL / Construyo mini TALADRO de mesa [1a Parte]](/img/tr.png)
![1908 Wine Corking Machine [Restoration]](/img/1.gif)
Поле чудес да и только и станки валяются и инструменты . Ходишь как за грибами. Захотел станок сверлильный нашел, захотел перфоратор.
😂потом на авито кинут. Биение пару соток😅 в идеале
Nice work. No lathe, no sandblaster, no reman parts. Just basic tools and hard work. Great job.
Excellent job resurrecting that old abandoned drill press. Now it can serve for another lifetime. Excellent!
ahhhhh paint ! very good for grapes ..... bon appetit . healthy for human and animal.
Если взялся за дело доводит его до конца. В твоём случае станок должен был что либо просверлить. А тут как он был сломан таким и остался. Доделай его до работоспомобного состояния и будет тебе лайк
Ни движек не поставил ни кнопку обратно
Где происходит эта ерунда? В какой стране?
@@maratmustafin9806 рф
I was looking for such a machine. And here he is!
Перекупская схема, помыть покрасить и на авито за три цены. На директлоте такой же нс-12, без стола и двигателя, за 4500р продавался недавно.
I applaud the job you did especially with so few power tool, it a good restoration. However please bolt down your vise, it's a beautiful bit of kit and deserves a permanent place of honour.
Do you applaud the fact that the machine was painted ? is this called restoration? This is a good machine, if it is restored, it will be able to serve for a very long time and help in the work ! but after such a restoration it is not a machine but just a useless twister with a beating spindle and a non-working cartridge !!! In our country, for such work, THEY are FIRED immediately !!!!
Мне вот так у всех под кустом свирлика воляиться ? И покраска проста божественна!! Но самое главное где станина и мотор? Или он от вечного двигателя работает? И как прекрасно бить по болту с резьбой молотком. Если-бы мне поймали на преждней работе за таким то руки отрывали с совсем корними
You should have put the first one of those bearings that went on the top of the quill drive in first then inserted the second. That would have kept their spacing.
Excellent restoration! Peace 💫
Not nice to be sarcastic Sandra . . .
J ONB unlike you I am not a hater.
Excellent Restoration!!!
👏👏👏👏👏👏👏
👌😁👌😁👌😁👌
👍😎👍😎👍😎👍
Anyone else screaming BOLT THE VISE DOWN... or is that just me.
no
Maybe he wants ! A Temporary ! Fixture !?
That and screaming use some dam penetrating fluid. Disassembly would be much faster
Temporary? No room on the bench? Drill a couple of holes through the bench top, secure the vise to the top with two or three heavy bolts, washers and wing nuts. When you’re done, spin the wing nuts off, remove the bolts and store the vise. The holes in the bench could be used with dogs for planning or sanding...simple. No excuse for turning a vise into a weapon.
Me too!
That was a lot of work done on a tool I wish I had. Good Job!
Достойно.
Oh look! Under this tree! It's that drill press I put there 2 minutes ago! WHAT ARE THE CHANCES?????
the same with the angle grinder! what are gthe chances?
LMAO I thought I was the only one calling BS on these videos. "I mean, I was mindin me own binuss and what do I's find!?!" Every video and their not the only ones who do it. Seriously, we don't need some story for the hunk of crap ... we just want to watch it get restored lol.
@@0420Junket I like the people who say: "I picked this up for ten euros/dollars at a scrap yard" or "someone was cleaning out an old storage shed and find this in the back" or something like that. I do not believe "my videographer was filming me when I found this piece of industrial machinery lying by the side of the road."
@@Ambidexter143 lol exactly. “This person with the camera goes everywhere with me. When finding tools, going the store or even taking a dump ... their there .” Lmao
good, the chances are GOOD
Almost finished, nicely done!
Very good restoration. You have demonstrated how much can be accomplished with hand tools and labor. Will the second part of the video include installing a motor? Good job!
31:12 now with added eccentricity, for 10% bigger holes. BUY NOW!
Теперь я понимаю суть фразы: покрасить и выбросить
Согласен. Залипуха!
Ето рождение новой фразы: смазать подшипник и выбросить!
Можно еще: из говна пулю лепить! ;-)
Mis felicitaciones por tan buena restauracion de este taladro de banco, gracias por este video y saludos desde Venezuela.
Hey great job mate , it is good to see the old gear being restored and looked after . Mate I have a question for you , can you tell me what those two extra belt pulley cogs on the side of the drill press are there for and what do they do as I have never seen that set-up on a drill press before . Also where does the electric motor go on the drill press . I hope this finds you doing another resto and I hope I am not bothering you with these questions .
I think some people have lost sight of the purpose of the video's it doesn't make ant differance how you come by the unit, as long as you have fun fixing and watching.
Hola...buen video...me parece que hay que agregarle musica de fondo....
thanks, great job, the camera is very zoomed in, can you zoom out little bit to get part of the holistic view? thanks again
Nice 👌🏻
Puppers is best assistant. :)
Обязательно положи на тоже место где взял. Следующий тоже должен получить свои лайки.
WOW !! How long did it take to do this?
Those grapes are going to taste funny after this spray job :-) (20min in)
That was actually well preserved. It look that way when it came out of the Soviet factory brand new.
BOM TRABALHO ,PARABENS AQUI DO BRASIL...
My favorite part was the magic at the beginning when it was “found” with no chuck but one appeared a few seconds later while still in the grass
No chuck, then a chuck, then no chuck again.. lol
A chuck chuck here and a chuck chuck there, old....
PARABENS NOTA 1000
It's thrown away not so long ago. Didn't rusted too much. No bolts unscrewing with acetylene torch. I think it's not even meets rain before you found it)
For the record, I've done this type of rebuild a few times. doing a BOISE CRANE 1800 at this time. Judging by some of the comments, I'm inclined to think this must be "open Sunday" in the lounge at the local sanitarium !! :)
Nice work
Досмотрел до момента когда убитый, рассыпавшийся подшипник начал собирать в шпиндель и сразу стало всё ясно, дальше смотреть не стоит,👎
Зато вал внутри шпинделя смазан толстым слоем солидола
Так ждал что он его действительно восстановит. Но нет. Просто почистил и покрасил.
В следующем видео будет показано завершение восстановления и запуск в работу. Только когда это будет.
Сам положил, сам нашёл - зачем восстанавливать.
Пиздец, даже кожух не разогнул.
@@stell33.stell33 видно по многому, что станок там лежал лишь летом, в сухую погоду максимум пару месяцев.
Super👌👌👌👌👌👌
I feel like i should donate just so this guy discovers a socket set.
Посадка под подшипник восле патрона прослаблена настолько, что обойма крутится.....
если бы он туда новый подшипник поставил то может она бы и не крутилась
@@TOP19809 там шариковый упорный подшипник стоит, его тяжело найти, автор решил не парится.
Да и посадки подшипников все стандартные, там конкретно просажен вал..
Очень похож на советский станок нс 12!
Рукожоп! Так испоганить добрый станок, который можно было бы привести в порядок. Сборка подшипников - шпинделя и втулки - в учебник ляпов при сборке. Браво!
Да, именно жаль станок. Попал не в те руки. 🥺
Good restoration
I'm not sure that this was an "actual find". But I do know that the puppy was a cutie. Did it work after all that restoration ? I didn't see the on / off switch replaced with the wiring.
использование дрели, зажатой в тисках, выдает вас как русских людей)
Интересно, а он знает, что такое ГОЛОВКИ???
А также что тиски не прикручены к столу выдаёт школьников
did you make the second video?
0:41 magically a drill head appears
Painted grapes. Good taste.
Восстановление методом покраски)
Fantástico trabajó
Nice. Now drag it back to the woods..
Hello, in today's video we will restore a drill press that I bought at a yard sale and clumsily threw in some bushes and covered up with a couple of sticks.......
good
Wondering why you didn't straighten out the belt guard before you Painted it and put it back together
Puppy checks out drill press and says, "Hold my vodka..."
No way those bolts would have come out as easy as that
Даже позавидовал -мне бы так ,пойти по маленькому в огород и найти станок ,не каждому так везет,а противовеса так ,случайно,нема было?
Осталось найти основание и мотор со шкивом. И поменять сверлильный патрон - его кулачки изношены до предела.
и добавочно заменить подшипники на пиноли
Now don't you worry, spelling not important here.
И здать нахрен в лом!
Great restoration 👍
Yes, I don’t buy the ‘find’. There is virtually no corrosion and everything is so well lubricated it comes apart with ease and no heat. The chuck and arbor were not there at the ‘find’ then they are mysteriously in the quill, then they disappear again before re-emerging. Would have liked to see a minimal protective coating or lubrication on mating and sliding surfaces during re-assembly. But still fascinating enough to watch to the end. Thanks for posting.
Parece Nuevo !!!
like it alot but maby brighter colours
lets see if I got this right....you used a spaner wrench to put it back together but not to take it apart?
Какой точности при сверлении достигли? 😂
Или сверлилка так, на всяк случай, чтоб было чем доску просверлить?
Жаль станок. 🥺
Ничего не восстановлено, сделано как попало, цвет - говно. Зря потраченное время.
Да его просто изнасиловали)
Если загонять деталь молотком, то это не восстановление. Так, почистили слегка
Ацкей , проведите такую же работу и , возможно, измените свое мнение..
Hubiese estado bien verlo en funcionamiento
патрон, в конце видео, офигеть как бьёт!!!
Так он ещё и бил по патрону железным молотком, прямо в район посадочного места, где конус 😖
Good job, bro! I like restoration, too.
The pulley nut isn't fully engaged meaning the shaft isn't inserted correctly.
Патрон зачем старый оставил? Где мотор, плита,ремни , стружка?
я в училище собирал такие станки токаря делали детали а мы собирали 10 станков в месяц должен собрать )))))))))))
You found that stored in an old she'd or something, no way it was in the weather and dirt for more than a week.
Isso que é restauração
Great video, let's do a good job together, see you guys again
Hello friend Vietnam
Вы зачем вытащили станок из гаража. Открутили площадку. Положили его под дерево и закидали ветками, а потом включили камеру и сделали вид, что он там до вас лежал. Такого не бывает!
At least the shaft turns and the quill moves. I'd love to see the runout measurements though. :/
It does look really poor... I wouldn't use it like that
Возьми себе за правило, все трущиеся детали смазывать при разборке и сборке. Применяй ВД шку или другую Смазку глубокого проникновения.
Удачная находка..
Добрый станочек!
Он его не нашёл, где положил, там и взял. Халтура, блин.
Hello from Azerbaijan
Радиально упорные подшипники собираются не запресовыванием а внутренняя обойма вставляется под углом к наружней и с проворотом. Для шлицевых гаек существует специальный ключ а не пробойник.
Вот это я понимаю, болгаркой зачистил и всё.
Nice . But where's the motor. Should have fitted one.
Peter at the end of the video it say's they're doing another video showing it finished plus how it works 👍.
The motor is under the 51 Hudson . It will be discovered next week.
It would take me a month to put it back together.
Cleaning up castings flaws but not putting in new bearings, Whats the point
Connect a motor and lets see it working!
Should have been changed the bearings. And the chuck
Agreed
The chuck is way obsolete. A keyless chuck would have been better. Good keyless chucks are not cheap.
@@firesurfer keyed chuck > keyless chuck
Какую смазку применяете?
Крем для лица, наверное?
Not impressed . The main shaft looked buckled when it was spun towards the end of the video and who in their right mind would re-use old worn woodruff keys and that old chuck. Filing new gear teeth on that massively abused chuck was the point where I lost faith in the restoration and couldn’t take it serious any longer. Why is it these “restorers” believe that the more metal you remove , the closer to manufacturing tolerance the part becomes???
Где найти рейку и крутилку что на колонке?(
Чего там ещё реставрировать?! Отличный станок,сразу тащил бы на барахолку-и так заберут...
👍👍👍
Where is the motor no clue how well it really works.
BL Restoration, what is that liquid you are using from that fanta bottle? white spirit?
Ех мені б хоча б такий.
Мне интересно после таких манипуляций с губками патрона он без закуси начал работать
nice what kind of threads does Russia use?
Metric threads, imperial threads are only in russian optic ( binoculars, old cameras...)
А моторчик где?