After seeing your video I decided to purchase the bearings and do it myself. Followed your instructions today which were very helpful and now I have a much quieter washing machine on its spin cycle. Awesome video - thanks very much.
Thanks for the help (HWF80BW2) much the same as in the video just a few things are different, the front panel has a couple of dowels down the bottom so once you’ve removed the screws pull it out a little then lift it up ( not hit down) and I found it easier to attach the pipe back on to the detergent dispenser before the front panel went on apart from that it’s an excellent video
If your shaft doesn't come all the way through the rear bearing (and you can fit the pulley onto the shaft); fit the bolt to the shaft and start turning. The pulley will act as a washer and you will pull the shaft back to where you want it. When it is in position you can torque the rear nut. I suggest a bit of lock tight on the threads too.
Mine is 12 years old and the bearing just started to become a little noisy. Looking at the pictures in the video how gross and rusty some parts are hard to believe its only 2 years old. Would suggest to clean all parts and inspect the motor brushes while it is disassembled for piece of mind.
Having just completed the job I would say they are on par with the other 'name' brands. Everything is logically placed, easily accessed once chassis panels are removed etc. Bearings go because water gets past the seal. The design of front load washers means the seal is not generally covered in water (as against top loaders). Of course, the cantilever design on front loaders means that shaft movement puts the seal under stress, which can lead to failure and allowing water ingress to the bearings. How do we resolve this problem? Easy. Do NOT overload the machine. Packing in clothes usually results in a lousy wash result anyway. Forget the marketing (8 kg etc). Use common sense. If the clothes cannot freely move in the drum during the wash cycle, there's too many in there. The Chinese bearings are pretty good, but you can always replace them with Timkins or SKS etc. Personally I don't think it matters in this application if you don't overload the machine. I found a button, a self tapping screw, and 6 coins in the pump outlet body (where the hose joins). Make sure you put your finger up the plastic pipe to see if there are blockages. DO NOT use fabric softener if you want your machine to last. It clogs up everything. To achieve a similar result use white vinegar instead. DO use concentrated front loader laundry detergent. DON'T use the stuff that comes in big boxes and is full of filler.
After seeing your video I decided to purchase the bearings and do it myself.
Followed your instructions today which were very helpful and now I have a much quieter washing machine on its spin cycle.
Awesome video - thanks very much.
Thanks for the help (HWF80BW2) much the same as in the video just a few things are different, the front panel has a couple of dowels down the bottom so once you’ve removed the screws pull it out a little then lift it up ( not hit down) and I found it easier to attach the pipe back on to the detergent dispenser before the front panel went on apart from that it’s an excellent video
Thanks for taking the time mate. Probably saved me hours of stuffing about with it. Especially like the freeze the bearings tip. Cheers!
If your shaft doesn't come all the way through the rear bearing (and you can fit the pulley onto the shaft); fit the bolt to the shaft and start turning. The pulley will act as a washer and you will pull the shaft back to where you want it. When it is in position you can torque the rear nut. I suggest a bit of lock tight on the threads too.
Thank you my seal went and the bearings where starting to get noisy thanks again
How long did the original bearing last? Are these machines reliable or well made?
This machine was only a few years old and in my opinion, No, they are not well made. (Made in China)
@@paulywooly almost everything made in China nowadays and it doesn't mean it is bad quality. This used to be true 10-15 years ago.
Mine is 12 years old and the bearing just started to become a little noisy. Looking at the pictures in the video how gross and rusty some parts are hard to believe its only 2 years old. Would suggest to clean all parts and inspect the motor brushes while it is disassembled for piece of mind.
Having just completed the job I would say they are on par with the other 'name' brands. Everything is logically placed, easily accessed once chassis panels are removed etc.
Bearings go because water gets past the seal. The design of front load washers means the seal is not generally covered in water (as against top loaders).
Of course, the cantilever design on front loaders means that shaft movement puts the seal under stress, which can lead to failure and allowing water ingress to the bearings.
How do we resolve this problem?
Easy. Do NOT overload the machine. Packing in clothes usually results in a lousy wash result anyway. Forget the marketing (8 kg etc). Use common sense. If the clothes cannot freely move in the drum during the wash cycle, there's too many in there.
The Chinese bearings are pretty good, but you can always replace them with Timkins or SKS etc. Personally I don't think it matters in this application if you don't overload the machine.
I found a button, a self tapping screw, and 6 coins in the pump outlet body (where the hose joins). Make sure you put your finger up the plastic pipe to see if there are blockages.
DO NOT use fabric softener if you want your machine to last. It clogs up everything. To achieve a similar result use white vinegar instead.
DO use concentrated front loader laundry detergent. DON'T use the stuff that comes in big boxes and is full of filler.