Thanks for your clearly explanation But I have a question. If I can use a lora module for more rang.. And what is best module that provides less time delay
Your Gerber is in error !! In the transmitter 5 volts it only arrives in the regulator 3v3. If using the AMS1117 3.3 you do not need the 1K resistor. The 10K resistor is also missing from the processor reset, both from the transmitter and the receiver. Whoever orders the plates will see that they do not work.
Can you please make one more transmitter and receiver but of 14 channel. Bro please make it we all are supporting you . Please please please . This was very nice and beautifully made . Your videos are awesome . Please make it
Sir RC TRANSMITAR H JO IC H12D, H12E, L293D, 7805 Transistor s Bana h sir iss se motar ko 5volt out put milta h jiss s motar ghumta h sir, RC transmitar k 5volt out put ko 12volt output kaise kre JIS se motar high speed s ghum ske
Brother i can not understand the s1 to s7 connectors or header pin purpose. please explain this. And if i attach a coreless motor with j1 header then dose it works??
How to setup Elevon Mixing (channel 1 + channel 2) for delta wing plane like f22 rapter,delta wing?? plz reply my question answer 🥲 in this transmeter and reciver
hello, thanks for this video i made the transmitter and receiver and their is a connection between them but i have a problem no channel on the receiver is resetting to 0 for example if i connect a led to a potentiometer CH the led doesn't turn off if the potentiometer is all the way down but i can increase the brightness of the led when i move the potentiometer up even servos don't move or the motor on esc ,i can control the throttle but not turn it completely off. the same happen with switches can't turn of a led but can increase brightness of led when turned on. please if you have any idea tell me thanks in advanced :)
Hello, I like your project, but since I am a beginner, I would like to ask. I need not only to send, but also to receive battery status data from the receiver. Unfortunately, I can't adjust the program to make it work. Can you please advise?
I was trying using nrf24l01 module with arduino, but could not communicate between two nrf24l01 module. Please make a video to live demonstrate how to use nrf module with arduino mega/nano from very begining level
Hey , I have already made it few days back but throttle joy stick is little tricky, did you modify it ? I have excluded spring so It can stays in same position.
Hi. I wonder can you help me. I have a parrot skycontroller for my drone. It is a wifi controller. The function for up down has stopped working. Controller connects to the drone and all other functions work. I can only assume the control chip in the joystick is gone bad. Where might I find a new chip to replace this? Parrot are of no help to me on this.
Sir i am havin a rc brushed motor mini quadcopter and i lost the tx, the drone is build with stm32f031k4 chip with xn297l radio chip, so i want to control that drone with ur diy tx, is it possible?
this is good work. can you kindly share your schematic diagrams sir. and if possible your code fro this demostration . the link in the description is broken i guess. thank you
@@rc3d490 aliexpress has the joysticks which have center as the 0 position which does not provide the full range of throttle . so that is the one i am asking for
I cannot open the both sketches... error is could not create sketch. I am using windown 7 32 bit. Can u post the sketch in *.txt format in your download else i won't able to learn anything. Please!
I don't know why people do not view this videos...awesomee👍👍👍
My dear, for watching only video, this video is perfect. But for implementing its not good. You should explain the parts also. All parts.
@Internet Gamer'z 360 that’s not an explanation, its a list
don't talk like idiot
Thanks for your clearly explanation
But I have a question. If I can use a lora module for more rang.. And what is best module that provides less time delay
Excellent project. But I'm unable to download the schematic diagram, it's not found!
Your Gerber is in error !!
In the transmitter 5 volts it only arrives in the regulator 3v3.
If using the AMS1117 3.3 you do not need the 1K resistor.
The 10K resistor is also missing from the processor reset, both from the transmitter and the receiver.
Whoever orders the plates will see that they do not work.
Can you plz provide rotary encoder switch link and which type of rotary switch we have to take plz replay Asap......,Thank you
We can't make make using NRF24L01 because there are some issues with range.
If you make it perfectly then there is no issue
@@EtDiscover NRF are good for RC boats cars but in case of planes if planes go out of range there will be a crach.
What rf module will be use if want to increase the range and libe streaming camera also
Next episode
Can you please make one more transmitter and receiver but of 14 channel. Bro please make it we all are supporting you . Please please please . This was very nice and beautifully made . Your videos are awesome . Please make it
My nrf24l01 attena module is not working properly .please give me suggestions 🙏🏻🙏🏻
Sir RC TRANSMITAR H JO IC H12D, H12E, L293D, 7805 Transistor s Bana h sir iss se motar ko 5volt out put milta h jiss s motar ghumta h sir, RC transmitar k 5volt out put ko 12volt output kaise kre JIS se motar high speed s ghum ske
Brother i can not understand the s1 to s7 connectors or header pin purpose. please explain this. And if i attach a coreless motor with j1 header then dose it works??
This receiver only for brushless motor Not coreless , This Receiver just produce sense
how to program IC without ur that programming device
You can using Arduino uno nano as you want
@@EtDiscover how
Sir please make a rc car and interface this remote contoller with it.
How to setup Elevon Mixing (channel 1 + channel 2) for delta wing plane like f22 rapter,delta wing??
plz reply my question answer
🥲 in this transmeter and reciver
Hi, sir in this drone use camera to fit this option is available
Can we use this reciever for brushed motor drone
Please reply
No
What changes should I make on the reciever for making brushed motor to work
yes
Atmega 328 p sm ke uper jo ic attach hi uska name btaiye aap
Ams 1117 ke bat kar rahe ho app??
If I make this then do I will need KK flight controller to control drone?
I like to use transmitter control via Bluetooth control in mobile, what type of board can I use, please give a good suggestion.
Which camera you used to make videos
Can we use it as flight control board for brushless motor drone
What should i use from ur list provided in description if i want to make only 4 channel transmitter nd reciever ?
hello, thanks for this video i made the transmitter and receiver and their is a connection between them but i have a problem no channel on the receiver is resetting to 0 for example if i connect a led to a potentiometer CH the led doesn't turn off if the potentiometer is all the way down but i can increase the brightness of the led when i move the potentiometer up even servos don't move or the motor on esc ,i can control the throttle but not turn it completely off. the same happen with switches can't turn of a led but can increase brightness of led when turned on. please if you have any idea tell me
thanks in advanced :)
What should you do with these diy projects after making these projects
can you tell me about this
Excuse me ....can you tell me which couse did you study to know about all this stuff
If I use this for making a quadocopter then I have to solder the accelerometer on the transmitter board???? Am I right ?
Hi, how did you modify the joystick potentiometers? Thank you!
Hello, I like your project, but since I am a beginner, I would like to ask. I need not only to send, but also to receive battery status data from the receiver. Unfortunately, I can't adjust the program to make it work. Can you please advise?
Bro AAP bressles motar bna sakte ho
Can we program ic with arduino uno ic socket by change this ic plzz tell
I was trying using nrf24l01 module with arduino, but could not communicate between two nrf24l01 module.
Please make a video to live demonstrate how to use nrf module with arduino mega/nano from very begining level
Tomorrow is my digital electronic exam 🤨 idk why I’m watching this but it’s great 👍 gonna make one as my project
Hey , I have already made it few days back but throttle joy stick is little tricky, did you modify it ? I have excluded spring so It can stays in same position.
You need to change Value of millisecond
preet charan what will I have to study to make this mu higher education
@@parshvapatel8484 degree in electronics
Wait… you’re offering the gerber files for free?? Bro you are my hero. I’ll donate to you In a little while. Ty so much.
please describe about the "rotary encoder"(sw1) in your ckt. where you have placed the potentiometer....can you give a link for the potentiometer?
can this be made with STM 32? STM 32 has better ADC resolution
Can we use a coreless motor in this
Sir me 2 remote Banana chata हू... To kya 1 transmiter se 2 receiver nhi chalege.. Na???
Code me kuch changes karna padega kya.. ❓
Which programmer modules did you use please?
I want to make one but I am making PCB at home and when I create schematic ,and tries to convert in PCB it says incomplete nets. Please help.
Hi. I wonder can you help me. I have a parrot skycontroller for my drone. It is a wifi controller. The function for up down has stopped working. Controller connects to the drone and all other functions work. I can only assume the control chip in the joystick is gone bad. Where might I find a new chip to replace this? Parrot are of no help to me on this.
Please tell me all over total budget for this project
How did you solder?
Google drive link is not working bro
Plz help me with it 🙏
Great i watch your videos for a long time they are wonderful , i'am ahmed one of your fans from morocco
Thank you so much
@@EtDiscover you ate welcom every time
can you pleas tell us how to configure mpu-6050 3 axis module in this transmiter to controol drone
How much volt did you used for reciver can we use 3.7v
which component is L3 AND R3 IN SCHEMATIC??
Pls give information about all the components of receiver boarx
Is this transmitter compatible with Whoop Lite F3 Mini brushed flight controller
I have only Arduino uno board can I directly connect it with transmitter for uploading the code .
If yes then how?
Can this work with unchangeable batteries ? Please reply
Kitna distance cover kr skta hai yeh drone.. Aur age range increase krna hoga to kya krna hoga. Yeh bhi batiye na..
Sir, what is the range of trancmiter and riciver
Cant you provide any circuit diagram for transmitter and receiver??
Sir i am havin a rc brushed motor mini quadcopter and i lost the tx, the drone is build with stm32f031k4 chip with xn297l radio chip, so i want to control that drone with ur diy tx, is it possible?
Sir where can we get the programming?
Hey bro what is the menziles? This transmitter
Please sir tell me where is it possible for me to dtmf and 2 mobile phones and use it as reciver and transmitter
What are the 2 pin male header on the receiver for?
where you got that components pls give me link
How did u do that yo your joystick
Please explain the programming part with normal arudino not your homemade
Can i program microcontroller ic using arduino
You can
Nicely done
this is good work. can you kindly share your schematic diagrams sir. and if possible your code fro this demostration . the link in the description is broken i guess. thank you
Can we increase the range and the no. Of channels??
Very good project I liked it
Thank you
From which state you are
Please try to make waterpump from old Brushless dc motor
Sir plsss add heatsink to the 5v regulator ic
Don’t need for this because here not too much current are consuming
How to make a electronic robot which operates the programic logic command.please basic training in robotics video.
from where do i buy that type of joystick
AliExpress
@@rc3d490 aliexpress has the joysticks which have center as the 0 position which does not provide the full range of throttle . so that is the one i am asking for
Amazon the purchase link is in the description box
which switch i can not hear in trans mitter
6:07 to 6:12 what you exactly did here?
Can i connect brushed motor to this
Nice vedio ...Mai bhi aisa hi project banaya hu
how to program ATMEGA328P SMD with bread borad
Where does The ANT wire go
Can you plzz give me the link of desired transmitter and receiver pcb board which you have asked from jlcpcb ..
Plz make a channel mixing (2 servo) ( channel 1 + channel 2) module circuit
Bro u r super and mindblowing work
And pls make a Brushed ESC for RC Trucks (I'm using fsi6 transmitter) it's working on ppm ports.
Ok I’ll try
@@EtDiscover Thanks... So many members r waiting for u r Brushed ESC video.
Thank you
Can u make a racing drone using this transmitter and receiver
Excellent work!!!
Your work is great!
Sir what is the range of this
Tx and rx
Can u make same concept for camera input and output purpose
How to make ppm or sbus reciever
Coming soon, next video
Thanks for replying 😀
Bahi pls ek rc sports toy car banaao plsss luv your videos
can lora be used for transmission
Sir your google drive link is not working please provide me a correct link i am also making a drone so i need this Tx and Rx
I couldn't make that work. I used two Nrf24L01+ but I only got 1 packet received in 10 sent.
Please how can I get all the exact electrical Components for the project such as capacitor resistors
Coba test jarak maksimal berapa meter...?
Good project 👏👏👏. Good editing
I cannot open the both sketches... error is could not create sketch. I am using windown 7 32 bit. Can u post the sketch in *.txt format in your download else i won't able to learn anything. Please!
Please bro please make it clear that how we will program the transmitter and receiver
How many metre done by without antena module
Hello. what is the encoder on the board used for? . can you order a stepper motor?
How can i make it