Very impressive work . Love the way you” clock up “ the work piece . A bit nerve wracking when you’re the last one to machine ,even if it’s a simple operation 🤣
EL PONER LA BRIDA DE SUGECCION EN MEDIO SIN CALCE DEBAJO ME DABA UN POCO REPARO .CLARO CON SEMEJANTE TOCHO DE PIÑONES EN UVE NO TIENE PELIGRO . PERO ES BUENA COSTUMBRE DE DEBAJO BRIDA CALCE O GATITO . SALUDOS .
Fantastic work. Sorry if my question is addresses in some of the non English comments. Is there a rule about positioning features (key ways or bolt circles) on an indexed feature ( gear, sprocket). To clock the features for timing? And how would that work for a skewed gear like this?
I am guessing it didn't have a tight positional tolerance. If so he would have had a vertical bar arrangement instead of a near horizontal one. At least that's how I used to do it before moving off the shop floor.
Knowing my luck if I tried a job like that I'd put the holes in the wrong end or put in seven or some damn thing. That part is only worth, what, $200000? No biggie.
Probably not that much but still way more then you'd like to pay out of your own pocket haha. Last Monday I had 4 titanium products each worth €10000 that had to be reworked but this time the CNC gods decided I was worthy haha
I was quite surprised that a woodworkers tape measure (like mine) was all that's needed to precisely position a ($ lots of money) pinion prior to such delicate surgery 🤔
Raymond muy buen video , su compañero es un excelente oficial , le consulto dos cosas ... las V esas son a 45° , y que marca es o que nomenclatura tiene. Saludos desde Rosario Argentina.
Los prismas en su interior tienen 90° y cada una de sus caras en relación a la base es de 45°. Se han construido en el propio taller y son herramientss muy utiles para sujetar piezas circulares. Gracias y un saludo desde España Jesús.
Es un macho de máquina para agujeros ciegos y va acoplado a un roscador automatico diseñado para fresadoras CNC aunque como se puede ver en el video también se puede utilizar en máquinas convencionales.
@@TheMetalRaymond muchas gracias por contestar colega , hace 16 años manejo máquinas cnc . Siempre trabajando con boquilleros y machos convencionales. Es un gusto ver sus videos. Un abrazo grande Maestro.
Solo nos queda estar de espectadores.... Saludos mi querido y estimado amigo...me imagino las noche que habéis pasado...pero digno de reconocer. Saludos desde Perú....
Друг скажи, пожалуйста, а как можно устанавливать деталь на посадочные шейки и обкатывать не прижатую деталь? Хотя о чем я, работа по 2 разряду. Успехов в работе
In the Android phone Playstore there are a variety of trigonometry applications to calculate coordinates. They are easy to use and very practical for this purpose.
Alguna marca en especial? Pues también realizo roscado pero solo atino a hacerle la entrada más no su totalidad, algún consejo para roscarlo de esa manera, gracias
Desconozco la marca pero son machos de máquina corrientes. Generalmente hay que taladrar el agujero al diámetro correcto que requiere el macho y hacerle un chaflán para facilitar el inicio.Si además esta en buenas condiciones de corte y le añadimos aceite adecuado para roscar no deberias tener ninguna dificultad para realizar esta operación.
O no se grabó, o se omitió del vídeo, pero sólo veo que el reloj comparador se usara para la circunferencia del eje. No habría también que usarlo a lo largo del mismo (o por lo menos a lo largo de la cara que se va a taladrar y roscar, para asegurar que queda perpendicular al mandril de la máquina?
Los prismas sobre los que se asienta el piñon van encajados en las ranuras de la mesa y estas a su vez están perfectamente alineadas con las caras exteriores y con el eje de la caña. Con estos útiles tan practicos no es necesario centrar el eje en su extensión, solamente centrar con el reloj en su circunferencia para buscar el centro desde el que partir.
УРА!!! Раймонд снова с нами👍😁
I myself work on a similar machine 2620В.
I always watch such videos with great interest.
beautiful work !
just would like to have the value of that piece in my pension plan !
Aprendo muito com seus vídeos e dicas...admiro muito o senhor,posta mais vídeos 🙏🙏🙏
Very impressive work . Love the way you” clock up “ the work piece . A bit nerve wracking when you’re the last one to machine ,even if it’s a simple operation 🤣
Bravo Turkey İzmir selâm 👍🌹
Muito bom parabéns . qual o nome dessa indústria q você trabalha?
Exelente. Gracias Sr.
Gracias amigo. 👍
Ai mà chê' tao ra liai may công cu này thât là sã Pham máy công cu tuyêt vöi
Si es una mandrinadora cnc, para piezas grandes.
EL PONER LA BRIDA DE SUGECCION EN MEDIO SIN CALCE DEBAJO ME DABA UN POCO REPARO .CLARO CON SEMEJANTE TOCHO DE PIÑONES EN UVE NO TIENE PELIGRO . PERO ES BUENA COSTUMBRE DE DEBAJO BRIDA CALCE O GATITO . SALUDOS .
Даааааа, большая деталька!!! :D И как всегда, ЛАЙК!!!
Спасибо друг.👍
ruclips.net/video/1M6ONMrBax8/видео.html
Ничего не понимаю, ваше видео без указания прямой ссылки на чужом канале.
Я всегда с удовольствием смотрю Ваши ролики.
Удачи и благополучия.
Спасибо другу за поддержку.👍
Gosto muito dos seus vídeos. Trabalhei muitos anos em mandrilhadoras aqui em SP. Brasil. No momento estou desempregado.
Obrigado pelo seu apoio neste trabalho, Ulises. Saudações. 👍
Excellent work👍👍👍 . Thanks for sharing
Thank you friend for your support. 👍
Me gustan mucho tus video amigo yo soy tornero en cuba te seguimos ❤
Fantastic work. Sorry if my question is addresses in some of the non English comments. Is there a rule about positioning features (key ways or bolt circles) on an indexed feature ( gear, sprocket). To clock the features for timing? And how would that work for a skewed gear like this?
Great work :) .... it is a hard job but i like it :) work as a cutting machine operator, too :)
At 2:31 do you have a known value you compensate for the indicator sag to find center or is the mm it is off not that important?
I am guessing it didn't have a tight positional tolerance. If so he would have had a vertical bar arrangement instead of a near horizontal one. At least that's how I used to do it before moving off the shop floor.
Ок
Sorprendente como se llama la maquina
What happen to the older guy?
This time it was the spectator.
@@TheMetalRaymond good to know, that guy has all the tips and tricks. Like the older guys usually do.
thump up, i do a similar responsible work as you !! good day and good work bb
Belleza de trabajo, saludos y éxitos maestro, cuidese y siga ilustrandonos con esa finura , 👍
Gracias Miguel por tus palabras de apoyo hacia esta labor divulgativa.Buen dia amigo.
Good work
Knowing my luck if I tried a job like that I'd put the holes in the wrong end or put in seven or some damn thing. That part is only worth, what, $200000? No biggie.
Probably not that much but still way more then you'd like to pay out of your own pocket haha. Last Monday I had 4 titanium products each worth €10000 that had to be reworked but this time the CNC gods decided I was worthy haha
Perdon por mi ignorancia, es CNC? Muchas gracias por su tiempo 🙏🏻
No es CNC.Es una maquina convencional.Gracias y un saludo amigo
Esa es una mandrinadora!!
Excelente trabajo compañeros. Bendiciones
Gracias Rolando. 👍
Kameremanın kim
I was quite surprised that a woodworkers tape measure (like mine) was all that's needed to precisely position a ($ lots of money) pinion prior to such delicate surgery 🤔
What name music
Excelente trabajo , felicitaciones por compartir tu trabajo maestro
Gracias amigo, por el apoyo hacia esta labor. 👍
Is this in spain...?
Какие обороты ставиш на метчик и какой это? Я под м12 ставлю 100 как думаеш эт норм?
Raymond muy buen video , su compañero es un excelente oficial , le consulto dos cosas ... las V esas son a 45° , y que marca es o que nomenclatura tiene. Saludos desde Rosario Argentina.
Me refiero a los datos del macho de roscar , y como se llama el mandril porta macho ese que se ve cuando rosca. Muchas gracias e saludos
Los prismas en su interior tienen 90° y cada una de sus caras en relación a la base es de 45°. Se han construido en el propio taller y son herramientss muy utiles para sujetar piezas circulares. Gracias y un saludo desde España Jesús.
Es un macho de máquina para agujeros ciegos y va acoplado a un roscador automatico diseñado para fresadoras CNC aunque como se puede ver en el video también se puede utilizar en máquinas convencionales.
@@TheMetalRaymond muchas gracias por contestar colega , hace 16 años manejo máquinas cnc . Siempre trabajando con boquilleros y machos convencionales. Es un gusto ver sus videos. Un abrazo grande Maestro.
Excelente trabajo...saludos desde Argentina 👍
Muito bom trabalho parabens
Obrigado Rogério pelo apoio. 👍
Do you also clock the side of the work piece?
Bhurelal Pradhan
I love your work and skill.
I have watched all your of videos. Some of them more than twice.
Love from IRAN. ❤❤❤
Thank you friend for your support. Greetings from Spain.👍
Sin margen de error !!!!!! Que maestro Raymond!!!!!👏👏👏👏👏👏👏👏 saludos desde Argentina
What a chunk of steel that started out as. Great job.
You have great machine 😍😍
Nice work
Thanks friend.👍
Excelente trabajo, como todos los demás, saludos
Gracias Fernando. 👍👍
👏👏👏👍👍👍🇧🇷🇧🇷
Don Raymond nunca en mi vida e visto el tipo de fresadora que usted trabaja ,ustedes las fabrican? O quien las fabrica.Gracias exelente su trabajo 👍🏼
Estas máquinas se fabrican en el país Vasco (norte de España). Gracias y un saludo amigo.
Only fellow machinists appreciate how much responsibility the re is working on a geared shaft that has so much skill already invested in it !!!
You are right. The responsibility in a piece of these characteristics is high. An error in its execution means a high cost.
Nice work, just LOVE that orizontal mill. It this iso50?
It's an iso s50. Thank you friend. Greetings.
Solo nos queda estar de espectadores....
Saludos mi querido y estimado amigo...me imagino las noche que habéis pasado...pero digno de reconocer.
Saludos desde Perú....
Gracias de nuevo compañero.Un abrazo desde españa.
hola, disculopa, podras explicar que porcedimiento hiciste , y como hiciste calcular los taladrados?
Depende que medida de tornillo vas a utilizar, barrenas el diámetro y usas el machuelo para hacer cuerda
Друг скажи, пожалуйста, а как можно устанавливать деталь на посадочные шейки и обкатывать не прижатую деталь? Хотя о чем я, работа по 2 разряду. Успехов в работе
Как ее обкатывать нежесткой стойкой вот так? Верх-низ могут смещены на десятку быть с такими трубками.
That has to weigh at least ~ 2000 Kg. Impressive workholding in terms simply of the weight of the piece :-) !!
2450 KG. It is exactly the weight of this pinion. Thank you and best regards friend.
True Craftsman
Andarilho
el macho que utilizas es vaporizado o de recubrimiento de titanio?
saludos
En esta ocasión se utilizó un macho con recubrimiento de titanio ,pero igualmente se usan los machos vaporizados para el mismo cometido. Un saludo.
Donde esta este teller?
Qué belleza.
Gracias por Compartir saludos.
Gracias a ti por el apoyo.Un saludo Alejandro.
Excelente trabajo colega
WOW WEE
Y Ramón?
How you found coordinates of the holes? Do you have some formula?
In the Android phone Playstore there are a variety of trigonometry applications to calculate coordinates. They are easy to use and very practical for this purpose.
Me gustaria alguien como usted en mi taller,felicidades por su intelicencia y experiencia
Gracias Juan por tu apoyo hacia esta labor. Un saludo.
Como siempre um bueno y pesado trabajo. Congratulaciones de Brasil!
Gracias Roberto. Saludos desde España. 👍
👍🏻🇪🇨
0:21 шевронные шестерни 0:31 с бородкой впервые вижу
gracias
Todas sus presentaciones si muy buenas...felicidades
Gracias Ramon.Saludos.
👍👍👍
Lo importante es saber que estás sano y bien. Ahora a ver otro ejemplo de un trabajo con excelencia!
Gracias Eduardo. 👍👍
P000999
Gracias por compartir tu trabajo.
Saludos.
Gracias compañero. Saludos. 👍
С возвращением
Primer like y comentario
Gracias por tu like.Un saludo Porfirio.
Que clase de macho usas, que tipo y marca usas para roscar toda la longitud
En este trabajo se utilizaron machos de M-22 especiales para agujeros ciegos que extraen la viruta hacia el exterior.
Alguna marca en especial? Pues también realizo roscado pero solo atino a hacerle la entrada más no su totalidad, algún consejo para roscarlo de esa manera, gracias
Desconozco la marca pero son machos de máquina corrientes. Generalmente hay que taladrar el agujero al diámetro correcto que requiere el macho y hacerle un chaflán para facilitar el inicio.Si además esta en buenas condiciones de corte y le añadimos aceite adecuado para roscar no deberias tener ninguna dificultad para realizar esta operación.
Trabajo hermoso!
O no se grabó, o se omitió del vídeo, pero sólo veo que el reloj comparador se usara para la circunferencia del eje.
No habría también que usarlo a lo largo del mismo (o por lo menos a lo largo de la cara que se va a taladrar y roscar, para asegurar que queda perpendicular al mandril de la máquina?
Los prismas sobre los que se asienta el piñon van encajados en las ranuras de la mesa y estas a su vez están perfectamente alineadas con las caras exteriores y con el eje de la caña. Con estos útiles tan practicos no es necesario centrar el eje en su extensión, solamente centrar con el reloj en su circunferencia para buscar el centro desde el que partir.
Que bien, gracias! no caí en la cuenta