Bro.....I was danger close to returning this thing. I could not figure out anything with it to save my life. I would plug in dual RCA to a mono 1/4 input jack and what I thought was the lowest audible setting it was stupid loud lol. Obviously it needed to be set to line level unbeknownst to me. I am new to all this. I'm a straight analog tube amp and cab guy who bought this thing to play around with a Tonex lol. Needless to say I was completely lost. I came across your video and you literally answered everyone of my questions perfectly. I can't thank you enough. Appreciate you taking the time to break it down for noobs like me 🤣
We're so glad to hear that our video helped you out! It can definitely be a learning curve when diving into new equipment, especially if you're more accustomed to analog setups. We're here to help, so if you have any more questions or need further assistance, feel free to reach out. Happy to have you as part of the community!
Thank you! Great, easy to understand. tutorial. I have two K12.2's on order and now I already know what to do, especially in the LED screen. I'm saving this video for reference!
@@edwinsprojects7039 Actually yes. A few months ago one of the speakers suddenly went silent during a solo gig. It turned out to be a software problem that needed to be updated on my end. The update was to prevent a shutdown that was intended to happen when the speaker was pushed too hard. However it was set too sensitive at the factory. I was not pushing them at all. Because I never registered the speakers when I purchased them, I didn't receive the update and never updated the software which would have prevented the shutdown of the speaker. So though I was still under warranty, and sent it in to be repaired, I still had to cover the cost of shipping which on a heavy speaker was over two hundred dollars. So lesson learned...make sure you register and stay aware of any software updates. Also registering extends the factory warranty. I did the update on the other speaker at home but it didn't work for the one that I had to send in. Other than that, they sound great and have been working fine since.
How do I get the volume up much higher on my K 12.twos I feel that the volume should go much higher than what it’s going, I’m a totally blind DJ can somebody help me
I recently purchased the K12.2 for the purpose of playing music from my phone, I have the bluetooth adapter but can I also play this speaker through wi-fi, if so, do I need another adapter?
I recently bought 2 QSC mains and 2 QSC subs. Set it up through my mixer how this video recommends and I keep losing sound to the mains. I have done 2 shows and have lost sound at least once for both events. I don't believe they are over heating because it lost sound 10 minutes after being turned on. What's going on?
MrMaui - same here - these speakers cut out. I opened a case with QSC they suggested to update the firmware - I did - same issue. I have been waiting for "weeks" for a reply from QSC - nothing. Terrible customer service. Shame should have researched these speakers. This is a known issue and it seems QSC is dodging the bullet. At this point - I would not recommend buying these speakers. I am still looking for remedy. Will try to come back and update if/when QSC replies. I spoke with a certified repair center ( 120 miles from my house). In my case, I'm asking QSC for the next step - again - nothing. I read on a reddit post that an engineer claimed he was replacing the amp-mod on many. The Engineer claimed the speakers are excellent just - it seems - a bad amp module. Apparently earlier Amp models were working fine but as soon as I mixed in drums - after some time - the speaker would cut out and needed a reboot. I'm not using them now. They are sitting in my basement, they look pretty and cost me a lot of cash but... useless. Again, will try to get back to you viewers with updates....
qsc 12.2 still actual and brand fixing some problems, or not in 2024? In between qsc 12.2 and Yamaha DXR12 mk2 for drum monitor, for edrums- to feeling punch, presence of edrums on stage.. Please help.
Hello, I have (2) new KS12.2s and (2) KS2121C and my question is once I select the setting on the KS12.2 to using a sub, I should just leave it to default? Thanks!
There are a couple of ways to go about this. Something that is common between the ways is running an XLR cable from your input speaker, we’ll call that one Speaker A, to the second speaker, Speaker B. My suggestion is to use the “Mix Out” from Speaker A and run it to “Input A”, the top one, of Speaker B. Do note that the “Mix Out” sums up the DSP setting from Speaker A. So if you do any processing on Speaker A, DON’T on Speaker B unless you really need to. BT Connection: Connect a BT receiver to Speaker A and wirelessly pair your device to the receiver. AUX Cable: If your device has a 3.5mm jack, you can run an AUX cable and plug it into “Input C”. You could also use a Multimedia Direct Box to convert the signal into XLR, but that’s kind of an extra step. Hope this helps!
I'm playing a vocal (A), acoustic guitar (B). Do I go through the setting process (most likely default), no sub, etc as you explained. Then do I go back and select channel (B) and go through the setting process again for channel (B) guitar? My acoustic guitar has a very sophisticated onboard pup system. Is default best for guitar channel? I've been using my old parametric system for 30 years so forgive me if I sound totally clueless. This is all new to me. Thank you so much for helping us out with this video. Great job~~!~~
Can I get some help I want to know why my speaker starts working good and we start playing and we get no sound It cuts off it doesn't power off So what I do I turn it off and power it back on and it works for a few minutes This is the 2nd time we use this speaks They are new so it frustrating can some one please help me thanks
I have the same problem. Used these speakers with 2 new subs that go with it. Have done 3 shows and at least once one of the speakers will quit working. Power it down then back on and it works again
Question...when adding a sub do you recommend line in first to the sub then slave to the main or line in to the main and slave to the sub. I see it recommend both ways
How to connect it with the KS112 Sub? Should I connect the line to the KS112 sub with 80Hz crossover, then connect to the K12 or should I connect to the K12.2 with 80Hz crossover then to the KS112 Sub? Which way is better?
Just wondering I have 2 of these and sometimes one goes out I have to turn off and turn back on any suggestions what it could be and my firmware up to date
Dear sir, I am waiting for my new k118 3600 w. sub to get here, I'm not a dj. I"m using it in a rock and roll band, combined with two k12.2speakers. what would be the best settings to use all around for a rock band?
rphurl13 I would start with the default settings (also recommended by QSC when using K series tops), which crosses over at 80 Hz and then passes the rest of the signal to the K12’s. This will give you a great sound and will work great for almost all applications.
If I want to connect a passive sub to these, am I right in thinking I can go in the following order? My mixer outputs (Dynacord CMS1000) to input 1 on each K12.2, then come from each output 1 to an external amp (in my case an EV P1250), and from there into the subs (in my case EV subs)? Then simply use the controls on the K12.2 to crossover at say 100? It seems simple, but before I damage anything it would be good to confirm! Many thanks in advance
Hi, Can we attach Y adapter to both A and B line in? If we do, what happens? Does it get more power or loudness? Or its not recommended. Please answer. Thx.
READ BEFORE BUYING - I have waited for the speakers for three months, and when I finally received them and used them at a gig last week, BOTH speakers reduced to almost inaudible levels of sound twice during the night and I had to go restart them. Once, I was only using the microphone and there wasn’t any music playing (I am a DJ) and it still reduced volume. I am reading that many other recent buyers of the speakers are having similar problems. I am searching for a solution because I would love to keep the speakers after all the great things I’ve heard about them, but I am not finding any to this problem. Anyone know what’s up??
@@aharonpearl9161 My first thought was the same, however, the clip light had not been on all night and the speakers were on separate power circuits. I tried them again at a different venue the very next week and had the same exact issue, except this time, one of the speakers would not turn on again even after restarting. I called QSC service centers, and they all told me that there has been a recent problem with the speaker amp module units, and many units have this issue. They suggested instead of repairs (since supplies for repairs are also backed up and many units are coming in with this issue) that I return my K12.2s. I have returned them and won't buy again. Extremely disappointing.
@@edwinsprojects7039 nope. I ended up returning them and decided I was done with the K12.2 since. Been looking at RCF since but haven’t pulled the trigger ($$$).
For audio cables we really like LEX and Whirlwind for XLR. A good budget option is HOSA's "Pro" series of cables. If you wanna learn more about XLR cables we posted a video about the topic recently: ruclips.net/video/dc3FiW4Mjkg/видео.html
Phil Cox Every speaker has its own amplifier and the outputs are only passing along the line/mic level signal from the inputs. No need to worry about impedance with powered speakers. :)
Quick question: we are using this without a mixer a vocalist with piano. Is there a way to add a slight bit of reverb to the vocal mic? Would this possibly be in the EQ settings?
I have a pair of Qsc 12.2 brand new speakers and I use it for a band . When I use the input 1 of the 12.2, it is clipping soon when compared to when I use the input 2. Any idea or suggestions which one to use
Check the input settings. You probably have it set to mic level which boosts the signal. If you’re coming out of a mixer into the speaker, the input should be set to line level. Check 3:00.
Why is no one talking about how weird it is that these speakers only have only one side handle? My JBL Eons (a handle on each side) were soooo easy to lift with my arms and place on the speaker poles, but the QSCs make it very awkward and dangerous. Lifting with my back instead of my arms. I think it's the weirdest design flaw I've ever encountered and I might have to sell mine even though the sound quality is fantastic.
That's a great question! Typically you will go into your powered sub first, as it has a built in crossover. This ensures only the low frequencies are being reproduced with your sub and it passes the crossovered signal to your tops. This will make them work more efficiently and give you great output.
Actually it doesn't matter which connection is first because the signal is processed prior to you plugging it in. Set that up first when you turn them on and are patched in.So if you run to you sub fist, select the proper crossover setting (for example: low pass at 80 then patch to your top main with low cut at 80) or patch to your top speakers input and patch to your sub, just make sure your settings are on the crossover are correct and you're good to go.
Need to EQ the lows out to use as a monitor for my CP88 Yamaha digital piano sounds. Right now a thumpiness bleeds through. How do you do this & save settings ?
I’m a dj and just bought 2 of these, I come from using mackie and JBL , had an issue with these speakers cutting out. I’m using a controller with no mixer, do I need a mixer with this type of speaker?
Bro.....I was danger close to returning this thing. I could not figure out anything with it to save my life. I would plug in dual RCA to a mono 1/4 input jack and what I thought was the lowest audible setting it was stupid loud lol. Obviously it needed to be set to line level unbeknownst to me. I am new to all this. I'm a straight analog tube amp and cab guy who bought this thing to play around with a Tonex lol. Needless to say I was completely lost. I came across your video and you literally answered everyone of my questions perfectly. I can't thank you enough. Appreciate you taking the time to break it down for noobs like me 🤣
We're so glad to hear that our video helped you out! It can definitely be a learning curve when diving into new equipment, especially if you're more accustomed to analog setups. We're here to help, so if you have any more questions or need further assistance, feel free to reach out. Happy to have you as part of the community!
Thank you! Great, easy to understand. tutorial.
I have two K12.2's on order and now I already know what to do, especially in the LED screen.
I'm saving this video for reference!
Hey congrats on your purchase. I ordered a few but have heard mixed reviews. Have you had any issues?
@@edwinsprojects7039 Actually yes. A few months ago one of the speakers suddenly went silent during a solo gig.
It turned out to be a software problem that needed to be updated on my end. The update was to prevent a shutdown that was intended to happen when the speaker was pushed too hard. However it was set too sensitive at the factory. I was not pushing them at all.
Because I never registered the speakers when I purchased them, I didn't receive the update and never updated the software which would have prevented the shutdown of the speaker.
So though I was still under warranty, and sent it in to be repaired, I still had to cover the cost of shipping which on a heavy speaker was over two hundred dollars.
So lesson learned...make sure you register and stay aware of any software updates. Also registering extends the factory warranty.
I did the update on the other speaker at home but it didn't work for the one that I had to send in.
Other than that, they sound great and have been working fine since.
How do I get the volume up much higher on my K 12.twos I feel that the volume should go much higher than what it’s going, I’m a totally blind DJ can somebody help me
Very nice review. I got this and Yamaha 06X mixer and TV don’t know how connected together
Great job dude. Thanks. Very thorough and clear
Very helpful but you didn't explain line B it has HI-Z/ Line settings you only talked about Mic/ Line settings
Hey boss can u tell me which preset is better for church setup. Also cp 8 or 12,good for Floor monitor. Please let me know.
I recently purchased the K12.2 for the purpose of playing music from my phone, I have the bluetooth adapter but can I also play this speaker through wi-fi, if so, do I need another adapter?
I recently bought 2 QSC mains and 2 QSC subs. Set it up through my mixer how this video recommends and I keep losing sound to the mains. I have done 2 shows and have lost sound at least once for both events. I don't believe they are over heating because it lost sound 10 minutes after being turned on. What's going on?
Dis you ever fix the issue?
Very good and simple explanation.👍👍👏👏
I have problem with the limiter never turn off the red light and the music stop while I playing music can you help me?
Following
Your signal is running in too hot
MrMaui - same here - these speakers cut out. I opened a case with QSC they suggested to update the firmware - I did - same issue. I have been waiting for "weeks" for a reply from QSC - nothing. Terrible customer service. Shame should have researched these speakers. This is a known issue and it seems QSC is dodging the bullet. At this point - I would not recommend buying these speakers. I am still looking for remedy. Will try to come back and update if/when QSC replies. I spoke with a certified repair center ( 120 miles from my house). In my case, I'm asking QSC for the next step - again - nothing. I read on a reddit post that an engineer claimed he was replacing the amp-mod on many. The Engineer claimed the speakers are excellent just - it seems - a bad amp module. Apparently earlier Amp models were working fine but as soon as I mixed in drums - after some time - the speaker would cut out and needed a reboot. I'm not using them now. They are sitting in my basement, they look pretty and cost me a lot of cash but... useless. Again, will try to get back to you viewers with updates....
Excellent review, thank you so much for your feedback and knowledge.
qsc 12.2 still actual and brand fixing some problems, or not in 2024? In between qsc 12.2 and Yamaha DXR12 mk2 for drum monitor, for edrums- to feeling punch, presence of edrums on stage.. Please help.
appreciate chief .. very helpful video
Glad we could help!
Very helpful tutorial!
Hello I have 4 ks118 subs. How do I connect all 4 subs and 4 K12.2 speakers? Thank u.
Now that guitar modeling is popular. can you do a video on the setting you recommend for FRFR use of the QSC..
Best speakers out there 👍
Hello, I have (2) new KS12.2s and (2) KS2121C and my question is once I select the setting on the KS12.2 to using a sub, I should just leave it to default? Thanks!
I have the exact same setup as you. Did you ever figure this out? What setting worked best for you? Sometimes I feel like I can’t get it loud enough.
How do you connect two speakers with tei k12 2 when you use your phone or tablet for audio music ?
How do you plug them?
There are a couple of ways to go about this. Something that is common between the ways is running an XLR cable from your input speaker, we’ll call that one Speaker A, to the second speaker, Speaker B. My suggestion is to use the “Mix Out” from Speaker A and run it to “Input A”, the top one, of Speaker B.
Do note that the “Mix Out” sums up the DSP setting from Speaker A. So if you do any processing on Speaker A, DON’T on Speaker B unless you really need to.
BT Connection: Connect a BT receiver to Speaker A and wirelessly pair your device to the receiver.
AUX Cable: If your device has a 3.5mm jack, you can run an AUX cable and plug it into “Input C”. You could also use a Multimedia Direct Box to convert the signal into XLR, but that’s kind of an extra step.
Hope this helps!
I'm playing a vocal (A), acoustic guitar (B). Do I go through the setting process (most likely default), no sub, etc as you explained. Then do I go back and select channel (B) and go through the setting process again for channel (B) guitar? My acoustic guitar has a very sophisticated onboard pup system. Is default best for guitar channel? I've been using my old parametric system for 30 years so forgive me if I sound totally clueless. This is all new to me. Thank you so much for helping us out with this video. Great job~~!~~
Can I get some help
I want to know why my speaker starts working good and we start playing and we get no sound It cuts off it doesn't power off
So what I do I turn it off and power it back on and it works for a few minutes
This is the 2nd time we use this speaks
They are new so it frustrating can some one please help me thanks
Same problem im having speakers are only 2 weeks New
I have the same problem. Used these speakers with 2 new subs that go with it. Have done 3 shows and at least once one of the speakers will quit working. Power it down then back on and it works again
Stop overloading the amp, leave enough headroom in the mix and it won't limit
I just purchased two ks12.2 when l turn them on with out anything hooked up to them I get a slight hum is that normal?
So I don't need a mixer? I can plug my AUX or jack straight into the speaker? And there will be sound?
Awesome tutorial mate
Thank you 🙏
Great video. Thank you!
No Problem!
Very informative! Thanks for posting. Subscribed and liked.
Thank you for your support, happy to have you a part of the community!
Question...when adding a sub do you recommend line in first to the sub then slave to the main or line in to the main and slave to the sub. I see it recommend both ways
EXCELLENT! Very helpful, thank you.
How to connect it with the KS112 Sub?
Should I connect the line to the KS112 sub with 80Hz crossover, then connect to the K12 or should I connect to the K12.2 with 80Hz crossover then to the KS112 Sub?
Which way is better?
Thank you for the info you are truly helpful
Just wondering I have 2 of these and sometimes one goes out I have to turn off and turn back on any suggestions what it could be and my firmware up to date
How do you connect the Sub to the speaker? … do you just use the line out ?
Dear sir, I am waiting for my new k118 3600 w. sub to get here, I'm not a dj. I"m using it in a rock and roll band, combined with two k12.2speakers. what would be the best settings to use all around for a rock band?
rphurl13 I would start with the default settings (also recommended by QSC when using K series tops), which crosses over at 80 Hz and then passes the rest of the signal to the K12’s. This will give you a great sound and will work great for almost all applications.
Thank you
I just purchase 2 K 12.2 I wondering the setting for my EV ELX200 subs when I use the k12.2
If I want to connect a passive sub to these, am I right in thinking I can go in the following order? My mixer outputs (Dynacord CMS1000) to input 1 on each K12.2, then come from each output 1 to an external amp (in my case an EV P1250), and from there into the subs (in my case EV subs)? Then simply use the controls on the K12.2 to crossover at say 100? It seems simple, but before I damage anything it would be good to confirm! Many thanks in advance
yes for sure ;) ig #djpaparazzii
how much?
Great video thanks
Hi,
Can we attach Y adapter to both A and B line in?
If we do, what happens?
Does it get more power or loudness?
Or its not recommended. Please answer.
Thx.
READ BEFORE BUYING - I have waited for the speakers for three months, and when I finally received them and used them at a gig last week, BOTH speakers reduced to almost inaudible levels of sound twice during the night and I had to go restart them. Once, I was only using the microphone and there wasn’t any music playing (I am a DJ) and it still reduced volume. I am reading that many other recent buyers of the speakers are having similar problems.
I am searching for a solution because I would love to keep the speakers after all the great things I’ve heard about them, but I am not finding any to this problem. Anyone know what’s up??
Either the gain is too high or the power in the hall was too low to power it. Never share a power line with the video lighting.
@@aharonpearl9161 My first thought was the same, however, the clip light had not been on all night and the speakers were on separate power circuits. I tried them again at a different venue the very next week and had the same exact issue, except this time, one of the speakers would not turn on again even after restarting.
I called QSC service centers, and they all told me that there has been a recent problem with the speaker amp module units, and many units have this issue. They suggested instead of repairs (since supplies for repairs are also backed up and many units are coming in with this issue) that I return my K12.2s. I have returned them and won't buy again. Extremely disappointing.
Did you ever figure out what the issue was?
@@edwinsprojects7039 nope. I ended up returning them and decided I was done with the K12.2 since. Been looking at RCF since but haven’t pulled the trigger ($$$).
Which is better for a church setting. Bose f1 812 or these ?
What brand of xlr are good for this speakers?
For audio cables we really like LEX and Whirlwind for XLR. A good budget option is HOSA's "Pro" series of cables. If you wanna learn more about XLR cables we posted a video about the topic recently: ruclips.net/video/dc3FiW4Mjkg/видео.html
So what if I'm mixing bass,guitar,and vocals?
I daisy chain 2 K12.2's on each side. Does daisy chaining change the ohms like when connecting raw speakers?
Phil Cox Every speaker has its own amplifier and the outputs are only passing along the line/mic level signal from the inputs. No need to worry about impedance with powered speakers. :)
@@aaronhein2824 Thank You!
Does the speaker have auto shutoff?
Yo didn’t explain the in eq and out eq diference!
Can you tell me about the limiter light?
Quick question: we are using this without a mixer a vocalist with piano. Is there a way to add a slight bit of reverb to the vocal mic? Would this possibly be in the EQ settings?
EQ will never give you reverb. Audio engineering 101
The speakers don’t have any effect built in.
Look into vocal foot pedals to add effects.
Did you need to adjust the equalizer. I found plugging a vocal mic directly in sounds very boomy and midy with no sibilence.
I have a pair of Qsc 12.2 brand new speakers and I use it for a band . When I use the input 1 of the 12.2, it is clipping soon when compared to when I use the input 2. Any idea or suggestions which one to use
Check the input settings. You probably have it set to mic level which boosts the signal. If you’re coming out of a mixer into the speaker, the input should be set to line level.
Check 3:00.
Thanks very good video
Please how to connect my phone wirelessly to qsc 12.2 speakers
Only way is to buy an external Bluetooth adapter
Why is no one talking about how weird it is that these speakers only have only one side handle? My JBL Eons (a handle on each side) were soooo easy to lift with my arms and place on the speaker poles, but the QSCs make it very awkward and dangerous. Lifting with my back instead of my arms. I think it's the weirdest design flaw I've ever encountered and I might have to sell mine even though the sound quality is fantastic.
Is there a setting for a condensor mic? I have a phantom powered akg 220
If I am using a mixer which I am, do I go into the k12.2 first, or go into the sub first?
That's a great question! Typically you will go into your powered sub first, as it has a built in crossover. This ensures only the low frequencies are being reproduced with your sub and it passes the crossovered signal to your tops. This will make them work more efficiently and give you great output.
@@VIPProductionNW thank you.
Actually it doesn't matter which connection is first because the signal is processed prior to you plugging it in. Set that up first when you turn them on and are patched in.So if you run to you sub fist, select the proper crossover setting (for example: low pass at 80 then patch to your top main with low cut at 80) or patch to your top speakers input and patch to your sub, just make sure your settings are on the crossover are correct and you're good to go.
What is the Gain C dial ?
It's to control the gain for the 1/8th inch aux jack to the left of the knob. Hope that helps!
@@VIPProductionNW thnak you
Need to EQ the lows out to use as a monitor for my CP88 Yamaha digital piano sounds. Right now a thumpiness bleeds through. How do you do this & save settings ?
Low cut at 80/100hz should do it
@@aharonpearl9161 thx, I'll try it.
power supply problem ..power come and go..what is the isue
Did you fix the problem?
Which input speaker hole do I hook up for playing from my MK3 to the speaker?
Use a mixer
Hi I’m getting air sound whenever I set my speakers at 0db and all levels on my Presonus 16.4.2 are down what can i do to get rid of the air
Use balanced cables and a grounded power source
I’m a dj and just bought 2 of these, I come from using mackie and JBL , had an issue with these speakers cutting out. I’m using a controller with no mixer, do I need a mixer with this type of speaker?
Did you ever figure out what the problem was?
@@edwinsprojects7039 negative! I don’t know what do with them
You should be covered under their 6 year warranty. Contact them and they should fix it or replace it👍
Nice Video
I seem to cut out and told turn off
Good review, too bad you didn’t actually explained the eq part..
Garcia Richard Anderson Jessica Hernandez George
Davis Mary White Kevin Thompson Kimberly
Davis Charles Lee Elizabeth Williams Donald
Brother - you must be under 5’ 😳
Harris Edward White Timothy Moore Daniel
Lopez Jessica Davis Carol White Jason
Thomas Larry Moore Melissa Jackson Lisa
Thompson Deborah Hall Karen Davis Daniel
Sounds crappy plugging a mic directly in without a mixer. Very muffled low end and mids are insanely overdone. No sibilence.
This guy is giving some wrong information.
Great video thank you
Moore Thomas Hall Jason Young Anthony