I like the set up to clean first, looks effective. Dont think I've seen grease fittings installed with air tools before...think I'll continue to use a small wrench or socket.
Yeah this is somebody that does this multiple times a day and clearly knows what they're doing the average person would mess those up just as often as it works out😂
Na you can only fuck it once anit was just in need of the good ol but wasn't taken it this solved that really any good solvent would have worked thru a grease gun would habe been the same hell hydro fluid in the grease gun could have been doneaswell
So true. You can see the cavernous space in between the fittings that allows the vibration and the shifting to really do damage. That grease will be gone in a mile if that.
This works every time. The bushings are not necessarily worn out. Farm machinery setting up from season to season nearly always has joints where the grease sets up like concrete. You can just use a port-a-power style jack with the jack fluid, transmission fluid, diesel, or rust remover. I've used all of these. They clean out the old setup greese and allow a path for the fresh greese. This is one of the advantages farm boys have in the real world. They know how to getter done.
Haven’t seen grease fittings on leaf spring shackles on regular trucks/cars since I was a kid, heavy equipment yes but not passenger cars, I’d say plain old utility trailers could use them too
Whole lot of expert mechanics in this comment section. I just want to know where to buy it. I've tried the hammer grease joint rejuvenator but it doesn't always work. I want that thing
@@alexduke5402 The thing is you do not have to! just make the ......... ok jag tar det på svenska för ni verkar ju totalt blåsta. Vad är det ni inte fattar? byt munstycke tryck in oljan sen är det klart!
Rasteretite čauru (podizanjem vozila ili polugom preko čaure) da bi mast prošla i sa donje strane bolcna. Deo je podmazan kad čista mast potekne na obe strane.
You need to replace the pins and bushings. You're still going to have the same problem next service. Plus your tires are going to wear out because the springs are moving all over the place and not keeping your alignment.
that blue color of the grease is beautiful , set against the drab grey machine. almost as if done on purpose, is this artistic expression or a how to grease the shackles video?
There’s supposed to be a seal in there right? Otherwise all the grease will get pushed away and not do its job.. may as well just keep putting grease in it every drive.. or replace it right..
Looks like a military vehicle service... those units needed to be replaced. No amount of grease is gonna fix a damaged bushing that has already begun to take on water
Unfortunately I've done this same treatment to heavy trucks & equipment myself in the past,, now I buy new stuff and kept serviced quite regularly.. It's hard to make a living with stuff that needs worked on all the time..🤫
If the bushing wore out this aint gonna fix that ..but over charge them and it will still have problems they will bring it back then u can replace bushing and charge them too much again. Altho i like the greese fitting idea . Manufacture should put greese fitting on way more stuff than they do
I have little fitting rejuvenators you load up with your mystery oil. Put on the fitting and hit it with the hammer and it shoots the oil through the nipple and fitting itself so flush out everything
What is that? If it’s lack of grease, and the old one she hard. It my works. But the the bushings is wiped out because of lack of grease. The all the new grease will be gone when you hit the fire pot hole
That’s a BIG 10-4, Sax Man!! To HE🏒🏒 with the GIC. They can take their Greasy ideas and go back to Greaselandia, or Greastantinople. Just leave the bacon grease - I needs it real bad (for my over easies). You can have my bacon grease when you pry it from my cold, dead hands.
This is like putting a plaster on a broken arm.... it ent gunna fix jack s. Just replace them, cause it'll be a matter of time before they fail completely.
Yes these bushings are worn. Yes It's not a bearing. Is it a bushing that needs grease? Yes. Are you lacking comprehension? Yes. Shoulda been a parts guy 🤷🏻♂️ oh wait that'll go over your head as well....
That bottom one looks phooked.. look at the centre, the nipple is the centre of the pin /bush,... oil n grease isnt going to do jack this time.. It may come out easier NOW, with the Lube...
All the grease in the world isnt gonna replace the lack of bushing 😂
There metal
@jbstepchild some are made of metal, these in the video are literally missing bushings completely.
@@jbstepchild*They’re
@lrgbrooks76 sry they is metal boy
Exatamente.
Flushing by diesel oil to remove old grease, then re greasing, nice job
Most likely they were not taking grease.
ج٩٨٨٨٨😮
خه٦😮😅ح😮😮😅😅من 😅😅😮ح٩😅٨٨٨٨😅😅من 😮😅😅😅😅😅ح😅من😅عندك@@PiotrT-ue1jwت😢😮م😊
@@PiotrT-ue1jw blocked grease port's, you can easily flush by diesel oul
Thanks
not diesel thats hydraulic fluid
Those bushings have left the chat
I like the set up to clean first, looks effective. Dont think I've seen grease fittings installed with air tools before...think I'll continue to use a small wrench or socket.
Yeah this is somebody that does this multiple times a day and clearly knows what they're doing the average person would mess those up just as often as it works out😂
Na you can only fuck it once anit was just in need of the good ol but wasn't taken it this solved that really any good solvent would have worked thru a grease gun would habe been the same hell hydro fluid in the grease gun could have been doneaswell
@@jbstepchild Can't tell if you or I had the stroke. Because I have no clue wtf you wrote.
@Watthead80 sorry man I have a tendency to drink an post online
@@jbstepchild lol all good man. At least it's nothing serious. 🤘
Nice trick, but its still just a band aid. ;)
Nah its planned, since then the customer comes back 2 month later, and all repeats.
You can put as much grease as you want it’s not gonna fix the worn out bushings
So true. You can see the cavernous space in between the fittings that allows the vibration and the shifting to really do damage. That grease will be gone in a mile if that.
This works every time. The bushings are not necessarily worn out. Farm machinery setting up from season to season nearly always has joints where the grease sets up like concrete. You can just use a port-a-power style jack with the jack fluid, transmission fluid, diesel, or rust remover. I've used all of these. They clean out the old setup greese and allow a path for the fresh greese. This is one of the advantages farm boys have in the real world. They know how to getter done.
Wasting all that grease! My shop manager would ring my neck 🤣
I worked for years as a heavy equipment mechanic. I wish I had thought of this.
Втулки требуют замены нет смысла уже промывать и смазывать люфт уже в сантиметр😂
да там и пальцу карачун
Your pin bushings are worn out.
Don't worry, they'll find out when they do double work next week.
grease takes up the extra space until it leaves the shop.
Судя по люфту, смазка уже не нужна😂
Ну да, верхний палец со втулкой вышел из чата😂
Смазка нужна всегда 😊
Exelente análisis 🇲🇽👍
За бадью под срачем отдельный РЕСПЕКТ!!!
А че, потом туда бумажек покидал и зажег... Нуль мусора....
MAINTENANCE IS TOO LATE....
My thought too....a PM in the PM 😅
Любой механизм любит чистку, смазку и ласку)
Tell me you're a hack without telling me you're a hack.
Awesome.... I m going to use this on my equipment I service. Thanks
Great idea, i had some dried out slip joints where I could have used this. Will try to get a setup for a neglected john deere 2130.
Haven’t seen grease fittings on leaf spring shackles on regular trucks/cars since I was a kid, heavy equipment yes but not passenger cars, I’d say plain old utility trailers could use them too
Wow fixed that buggered bush
Nothing was repaired in this video. Bushings still junk
зато не скрипят! :))))
Whole lot of expert mechanics in this comment section.
I just want to know where to buy it. I've tried the hammer grease joint rejuvenator but it doesn't always work.
I want that thing
Make it..
just make an adaptor for the portopower and push hydraulic oil in there.
( Do not change the nipple portopwer straing in the nipple)
@sopalen I'll have to do that. We just got a pp a month ago. I can probably make adapters on the lathe
Sometimes a little grease goes along way.
@@alexduke5402 The thing is you do not have to! just make the .........
ok jag tar det på svenska för ni verkar ju totalt blåsta.
Vad är det ni inte fattar?
byt munstycke tryck in oljan sen är det klart!
Never install grease nipples with a power/air tool. Always use a hand tool.
STFU. He started them by hand and just ran them home. People who are used to doing this don't have any issues.
I would like to see the rest of the tool that thing is really neat
Rasteretite čauru (podizanjem vozila ili polugom preko čaure) da bi mast prošla i sa donje strane bolcna. Deo je podmazan kad čista mast potekne na obe strane.
If you grease fittings regularly you dont have to do this
cant argue with that
Cool. Getting all the crap out and filling with fresh grease. Good work.
Nice job?that how you do it.
Лучше один раз поменять чем 100 раз помазать. 😅 учитывая стоимость смазки ☝️
The lower pin inside has not unlocked and the grease does not pass through.
If you would take a Jake and relieve the tension on the shackle the grease would get around the pen allot easier.
You need to replace the pins and bushings. You're still going to have the same problem next service. Plus your tires are going to wear out because the springs are moving all over the place and not keeping your alignment.
Seems like a great way to strip the threads real nice lol
I bet that would cost you a 10k fine in California.
Mấy cái ắc nhíp này chắc vào tháng rồi chưa dk bơm mỡ 😂 , nước còn đọng vào lỗ bạc 😅
ليس ماء هذا زيت خفيف لفتح المسامات ثم الشحم
The amount of moving you just made packing that grease is crazy...replace the bushings
This lòks like a good time to replace that bushing over flushing out the grit that is wearing on the spring pin.
When i grease forklift trunion cap bushings with my electric grease gun and the grease pops through, it is so satisfying lol
What is going on here? A flush on the suspension? It's only a bandaid.
So that's why it always looks like your trucks have diarrhea 😅😅
Work smart not hard , great example right there
It's blue!
Oooooohhhhh!
I like Valvoline Crimson.
Looks like Closeup😅
Want to do this for my rear axle shafts!
that blue color of the grease is beautiful , set against the drab grey machine. almost as if done on purpose, is this artistic expression or a how to grease the shackles video?
There’s supposed to be a seal in there right? Otherwise all the grease will get pushed away and not do its job.. may as well just keep putting grease in it every drive.. or replace it right..
@Pancio27 Yes the grease does go through. Look at the lower right edge and you can clearly see grease coming out.
Eu achava super interessante quando fazia isso na minha brazuca... Ficava super macia🎉
Looks like a military vehicle service... those units needed to be replaced. No amount of grease is gonna fix a damaged bushing that has already begun to take on water
People have no idea how long a well maintained machine can serve them. They're treated as almost disposable.
Unfortunately I've done this same treatment to heavy trucks & equipment myself in the past,, now I buy new stuff and kept serviced quite regularly..
It's hard to make a living with stuff that needs worked on all the time..🤫
If the bushing wore out this aint gonna fix that ..but over charge them and it will still have problems they will bring it back then u can replace bushing and charge them too much again. Altho i like the greese fitting idea . Manufacture should put greese fitting on way more stuff than they do
I suppose when you pay for the tube of grease. They're gonna use it regardless of on bushing or in bucket
So where do the bolts go... remove them and insert zerk fittings.... got it ty sooo much🤦♂️
I have little fitting rejuvenators you load up with your mystery oil. Put on the fitting and hit it with the hammer and it shoots the oil through the nipple and fitting itself so flush out everything
Ни когда об этом не думал🤔🤔🤔🤔🤔🤔.. С начало маслом промыть.... Хорошая идея
Солярка
I'm confused, I haven't worked on very many leaf springs, but don't the mounting bolts go there where the grease zerks are??
I think you didn't put enought greases ????
removes old grease.
Wasnt the point of the first step to remove the old grease?@@tkmaniac5812
He put enough, supposed to push out old grease and dirt
Looks like the owner of the truck needs to get on a regular service program.
The story about how I became a maintenance man. I get paid by the hour. So, I’ll come back tomorrow and put more grease in it 😂
Marine grease only works on the ocean. Not on land vehicles! It just stops and doesn't do anything. It stops working
The coolest thing in the world is when people know how to do their job and take pride from doing it right.
You obviously didn't notice the bushings are worn out. Didn't you see the movement? You know nothing and should fix anything.
Shouldn't , if your gonna talk Sh@t then at least spell what you say correctly Einstein..... Smh
Like, I don't get it.Why aren't you replacing the brushing?Isn't that the point?
That bracket has seen better days
Looks like time to change those !
Do this 2 times and the thread is scrap like the bushings.
lol, are you professional excuse maker? Maintenance isn’t something your used to huh? Nothing last forever
Wouldn't the grease eat the rubber bushings?
Will most definitely save some pins and bushings.
shit aint free boi...
What is that? If it’s lack of grease, and the old one she hard. It my works. But the the bushings is wiped out because of lack of grease. The all the new grease will be gone when you hit the fire pot hole
What is this fitting called interested in one
Maybe actually repair the bushings, then grease it
Kafana göre heryere ağaç dikemezsin çölü ormana çevirirsin bu sefer diger taraf çöl olur
This must be sponsored by the Grease Industrial Complex.
That’s a BIG 10-4, Sax Man!!
To HE🏒🏒 with the GIC.
They can take their Greasy ideas and go back to Greaselandia, or Greastantinople.
Just leave the bacon grease - I needs it real bad (for my over easies).
You can have my bacon grease when you pry it from my cold, dead hands.
しばらくの間
グリス充填OK👍
The leaf spring mounts on my van have a bolt for the spring bushing to sit on ..how u change this spring remove entire mount ??
Bushings are still bad and the bottom didnt even take grease all the way. Nice hack job
A bad bushing is a bad bushing needs to be replaced but grease won't eat up rubber it look like oil that was put on an oil does eat up rubber
What kind of grease gun tip is that?
Super 👌👍👏
You gotta get the weight off the springs first.
This is like putting a plaster on a broken arm.... it ent gunna fix jack s. Just replace them, cause it'll be a matter of time before they fail completely.
Браво аплодирую стоя 👏
What are the tools they are using
That’s a great job 😊🎉
手動のグリスポンプではグリスさせないやつとかあるけどこれでグリス出てきたら気持ちいいだろうな！
Bushings and shackle pins are worn . Repair by replacement ✅
Since I change these daily I'd say u don't need grease there buddy u need a new bushing 😂
Lube Job not supposed to be an Undercoating ?
If it leaks grease like that, you have bigger problems.
Aren't the bushings just worn? Its not a bearing which you put grease in. Looks like a solution used for the wrong problem
Yes these bushings are worn. Yes It's not a bearing. Is it a bushing that needs grease? Yes. Are you lacking comprehension? Yes.
Shoulda been a parts guy 🤷🏻♂️ oh wait that'll go over your head as well....
That bottom one looks phooked.. look at the centre, the nipple is the centre of the pin /bush,... oil n grease isnt going to do jack this time..
It may come out easier NOW, with the Lube...
I like butter on my breakfast
Do you like butter on your sausage?
Keşke eski kurumuş yağlarida bi temizleseydiniz
What solution is that going into the tool I also need the name of.
We just replace those 😂
clean all AROUND and inside to see what is going on. then grease.
ハンガーめっちゃ動いとるやん！早い所シャックルピン・ブッシュ・ハンガー交換しとこうや。走行中に1番リーフ飛ぶで？
Nobody does this anymore. I remember my Dad taking in the family car for a lub and oul change. Nobody does the lub part.
What does this have to do with butter?
What is that thing called? I need it.