Very fun to watch. I always wanted to know what the inside of a compressor looked like and how it worked. I spent 4+ years in Korea in the early 90's and I'm telling you, Koreans are very talented and can fix almost anything. They do not waste. Well, that's how it was in the 90's :-) I assume it's the same now. Great video.
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
When you make these kinds of videos come with more information like the issues and what has to be fixed not just open clean and close it remind me like watching Charlie chaplain's funny video.
9:10 The discharge valve blade and its base plate should be polished on the glass with the finest lapping paste. Since you have dismantled the compressor, this important operation should have been performed as the compressor is not a serviceable type.
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
Ai quem me deram desse ficou da hora viu da hora mesmo você é o cara certo para fazer esse tipo de coisa sou de Alagoas Sebastião de Sena palmeira dos Índios bom dia meu jovem bom dia bom trabalho fica com Deus
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
Hello I have a question about my compressor in my vending machine. my machine was melded the start relay also I replace the new one. After I look at the start relay operate voice but the compressor not run I use the volt mete to measure the C to S and C to R the reading C to S very high 2.3 Mk ohm C to R 2 ohm. is it the compressor the wiring damage ?
-I just poured the oil and then I gave it a test run, but during the recording I skipped that phase -Thanks for watching and supporting me. Thanks very much!!!
I am new in this field, if I am not wrong as per I know that, two terminal point ohms’ continuity is OK, but third terminal point ohms’ continuity is “Null” that's means compressor motor coil is faulty, without rebuild the Faulty motor how can it work?
It ran low on refrigerant and the oil ran low....seizing the position rod onto the crankshaft. That's why he had to use a puller to get it off. What he didn't show is him refilling it with oil before he ran it.
Bom dia meu jovem bom dia você sensacional viu é demais você é incrível você desmanchar e fazer de novo que dá tudo certo se eu soubesse desmanchar eu faço isso também é demais você viu bom dia bom trabalho
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
مشاالله ازت مهندس بی حیله.. سایه ات مستدام تا اینجا برام امتحان خوبی بود همیشه دنبال ویدیوهات هستم🙏🏻🙏🏻🙏🏻🙏🏻💐💐💐💐⚘⚘⚘⚘👉🙏
Bravo champion 👍💪👏😊
😊😊❤
ok na ok. ang galing mo pre.
Thanks for watching and supporting me. Thanks very much!!!
What do you use to clean compressor...whiat liquid are u using
great job man👍👍👍
مشكور كثيرا على الابداع و الاتقان في العمل
Great work sir
hey brother! what did you mix with water to clean insides?
Thank you
I would have capped off ref line while painting
It is a good work. I thank you!, (Erevan)
thank you very much.
Great craftsmanship.
👏👏👏👏👍Fantástic
😁
Bravo to you
Number one..
Good video 🇵🇰
nice work
good technician i think from phillipine.
Very fun to watch. I always wanted to know what the inside of a compressor looked like and how it worked. I spent 4+ years in Korea in the early 90's and I'm telling you, Koreans are very talented and can fix almost anything. They do not waste. Well, that's how it was in the 90's :-) I assume it's the same now. Great video.
nice and thanks for your video
Muchas gracias por este video
Aprendí mucho hracias
العز والرضا المعلم و البروفيسور
Good ❤
Thank you very much. Please follow and support us!
Video quality is very well
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
super travail, je félicite, bonjour de France
Thanks for watching and supporting me. Thanks a lot!!!
congratulations!!
Thanks a lot
Excellent job.tkx.
Perfect
Just cleaned it , and everything fixed , whoa ! !
Thank you very much.
GOOD JOB! I NEED TO DO MINE TOO
Thank you!👏👏 Very educational 👍. What about the oil that comes in compressors🤔?
Wow bon travail mon frère si non vous avez lavé ça avec de l'essence ?💪
Thanks
. Please follow and support us!
When you make these kinds of videos come with more information like the issues and what has to be fixed not just open clean and close it remind me like watching Charlie chaplain's funny video.
Dime querido, ¿qué líquido usas para enjuagar? ¿Por qué no cambiaste la Junta?
saludos brother que tipo de electrodos usastes para la soldadura
Good job
9:10 The discharge valve blade and its base plate should be polished on the glass with the finest lapping paste. Since you have dismantled the compressor, this important operation should have been performed as the compressor is not a serviceable type.
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
@@restorationsskills4967 .ml Llo 9pp
@@restorationsskills4967 Thank you kindly for your very informit video! I have always wondered if they could be rebuilt.
Ai quem me deram desse ficou da hora viu da hora mesmo você é o cara certo para fazer esse tipo de coisa sou de Alagoas Sebastião de Sena palmeira dos Índios bom dia meu jovem bom dia bom trabalho fica com Deus
классный аквариумный компрессор получился из цикла когда коту делать нечего!
5:23 what's in the bottle?
Thank you very much. It is the liquid used to clean the compressor
@@restorationsskills4967 ok, what kind of liquid?
Good job bro...
Excellent
It's wonderful
wow very talented
So nice to see you used primer on the baer metal. This makes the top coat really stick.
Bravo!
Very lesson
Good lesion team
my refrigerator machine might be the same damage as in the video🙏🙏👍
Buen trabajo bro
Parabéns amigo gostei muito
High press must be more than 450 per square inch (Psi).
Good job....🙏
Excelente Trabajo, "Pero" porque pintarlo de negro otra vez, si hay bastantes colores, es mi opinión, saludos desde México 🇲🇽👍
Супер 😃😃💪💪💪
Oky very good
Thanks for watching and supporting me. Thanks very much!!!
Saft contacting piston is always be checking & only fitting new head valve plate gasket.👍
Thank you very much. Please follow and support us!
Yeah don't mask the inlet and outlet tubes, spray them, spray paint into them! Why not a little masking tape?
Great come to us
Thank you very much. Please follow and support us!
Ты просто супер и топ 😃💪💪💪💪
parabéns amigo ótimo trabalho
congratulations friend great work 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
❤❤❤❤❤
Thank you very much
Very useful work ethic, 👍
ótimo trabalho..........👋👋👋
Thanks for watching and supporting me. Thanks very much!!!
Miguel
Çok güzel tamır ettiniz..Elinize saglık..
vvvji
Qiciera saber qe tiempo puede funcionar el motor del refrijerador como compresora para pintar bicicletas podia indicarme gracias
Very good job, but why didn't you add oil to the engine? Thank you
Wonder how long it lasted?
nice
GangNam style!!
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
That was incredible. you are very talented. I enjoyed the video.😀
العمل كله تمام ولاكن ماشفتش حطيت زيت ولابد من مسح بلف الطرد الجوازات من الواجب التى عليها وشكرا معزرة
In the video it does not show putting the new oil inside the cylinder. Without oil the engine will not spoil again?
Самое главное перчатки и пинцет, тогда ремонт будет удачный.
Hello I have a question about my compressor in my vending machine. my machine was melded the start relay also I replace the new one. After I look at the start relay operate voice but the compressor not run I use the volt mete to measure the C to S and C to R the reading C to S very high 2.3 Mk ohm C to R 2 ohm. is it the compressor the wiring damage ?
If your common to start connection is showing 2.3 megohms it has a problem as that is way too high.
It would need rewinding.
after painting, it also paints the power terminals,
Ferfecto
Ok from iran
Thanks for watching and supporting me. Thanks very much!!!
Cool
Buenísimo súper hintelige
Thanks for watching and supporting me. I really appreciate it! Thank You Very Much!!!
Nice video.But do you need to fill in oil?
-I just poured the oil and then I gave it a test run, but during the recording I skipped that phase
-Thanks for watching and supporting me. Thanks very much!!!
Did you put the oil in before you welded the case shut, or afterwards?
Overolling evrthing reparing welding and fixed redy after oil filling ok .
As a refrigeration and ac engineer. This is the funniest shit I've seen in a while. 🤣
چرا بعد از تعمیر و سرویس روغن مخصوص را به آن اضافه نکرد(نریخت)؟
How many litres of oil do you put in a compressor and what chemical is used to clean inside and compressor inside components
Depending on the size of the compressor. We use specific detergents for compressors
I am new in this field, if I am not wrong as per I know that, two terminal point ohms’ continuity is OK, but third terminal point ohms’ continuity is “Null” that's means compressor motor coil is faulty, without rebuild the Faulty motor how can it work?
enjoy it
Would be nice if you would explain what’s broke and how you fixed it
It ran low on refrigerant and the oil ran low....seizing the position rod onto the crankshaft. That's why he had to use a puller to get it off. What he didn't show is him refilling it with oil before he ran it.
@@AutismusPrime69 thanks.
@@AutismusPrime69😮😮😮😮😮
Did you put oil?
Πώς θα βγάλω την σκουριά από εργαλεία
Great job man !!!!!!!
Bom dia meu jovem bom dia você sensacional viu é demais você é incrível você desmanchar e fazer de novo que dá tudo certo se eu soubesse desmanchar eu faço isso também é demais você viu bom dia bom trabalho
ماشاء الله روعة
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
Já instalei o famoso motor " Recon" recondicionado!
You did not add fresh oil inside the compressor ?
😮😮🔧🔨❄❄👍👍👍👍
Es.completo lo felicito a pezar que no explicó.
Me gustó, gracias.
💯💯💯💯💯
It needs fridge compressor oil.
He hasn’t added oil and sealed ihe suction and pressure ports before repacking it !
@@jerrypilet5283 ц
What about the oil that was in the compressor? I have not seen you adding back any oil, is this normal?? Is it
จิตตจของตนคือจจากตัวจริงจต่อจากจะจัดตั้งจังหวัดตากจะต้องตกแต่งตกจตจขใจจจะจัดจำหน่ายและบริการจากตัวจริงต้องจ่ายตังค์จจากตัวจริงตามตัวจจจากตัวจริงจจจจจจจขจมมไม่มีีีจจจจใจสนฟ
I hope that you filled it back up with oil 😮
Main thing is properly gasket gasket kit fitting otherwise nothing with compressor big issue & cleaning properly.
мастер 80го уровня!
хрень полная
Compressor oil, psi?
Depending on the machine to add oil
How much you charge service cost for repairing the compressor customer