Thanks and I’ve just done one for a family member. The top left nut doesn’t need removing it has large plastic spring clip, so remove the bottom nut, insert your hand top left and down the side and you’ll feel a prong. Push it in and it unclips. Thanks great vid.
Mondeo station mk4.5 is a bit different. Remove screws from opening latch. Remove plastic cover from inside. Remove 2 M6 nuts left en right from the inside. Unhook the panel in the center from the inside. Then remove the panel with the Ford logo from outside. From there procedure is self explanitory. The disconnect electritycable from the lamp use a screwdriver to depress the protection.
Yep, I tried to pull off the tailgate release panel above the number plate as per the video, thinking I just had to pop a few clips, well something popped and it wasn't the clips, I broke both mounting brackets, nightmare repair gluing that back together.
@@spookbok When using glue, using baking powder where you cant see it or use some fiber with epoxy. Isuggest google or youtube baking powder with superglue.
The biggest problem was the very thin section of the brackets. Once the glue was on I couldn't locate the correct position by feel. Usually broken surfaces will lock into place but that was not the case here. Interesting tip about the baking soda. I used 2 pack epoxy which has worked very well.
Pozor!!!U mk4 kombi je to trochu jiné.Pro sundání lišty se znakem Ford je potřeba vyšroubovat dva šrouby u osvětlení registrační značky.Poté sundat tapec dveří a odšroubovat další dva šrouby.Každý na konci lišty.Je lepší sundat i rámeček registrační značky pro lepší manipulaci.Zbytek je stejný jako na videu.
Hi, if you mean first part where is Ford logo there are only 4 clips and not any screws (you may see it when I remove cover, those blue clips inside), you need to pull it, on each side there is small ear where is this plastic cover gripped, you need to unhook it.
On my MK4 accessing the lights from inside boot lid I was not able to remove the clear reverse light bulb at all but the other smaller T10 501 bulb can be removed without full tear down. There doesn't seem to be enough clearance to remove reverse light bulb. Is there any way of removing that reverse bulb without having to remove the whole cluster like in the video? Then install smaller brighter led bulbs which will allow you to remove the bulb without having to tear the whole back apart. Especially those blue clips from the start they broke on mine.
I needed to remove whole light as my led was broken, but if you need to remove only clear reverse bulb and there is not space through small back plastic cover, you probably need to remove whole plastic cover inside of trunk, it should be enough space to replace that bulb
@@michalorlicek6057 ohhh cheers didn't think of that way instead of the outside tear down. It is quite annoying that they designed consumable parts of the car to be very difficult to access. Might give it a go but first going to look for some small leds of the same style that may help in future light removal.
@@michalorlicek6057 Ive found on a forum someone mentioned they removed two nuts holding the light housing from incide and just pushed it slightly. This way the ear didn't break and they were able to remove the reverse light. However they could not put the light back in so removed the whole back as you did 😃 I'm thinking if I find a smaller p21w led bulb it might be possible to remove after initial strugggle the led bulb easier in the future.
Świetny film, dzięki! Problem mam ze złożeniem elementu do którego przyczepiona jest tablica rejestracyjna. Pomiędzy plastikiem a metalowa częścią klapy zostaje dość duża szpara. W jaki sposób mogę dopasować ten element?
All this just to change a reverse bulb is madness 🤦♂️ thought it was a 2 second job like it was on my old passat. May get a garage to do it for me as i will undoubtedly break a clip when trying
Yes, as inner tail light has ear which is behind plastic back panel where is plate, see here: www.aliexpress.com/item/1Set-2Pcs-Inner-Outer-Rear-Lights-Tail-Lights-Taillamps-Right-Side-for-Ford-Mondeo-Fusion-2011/32828169232.html?spm=2114.search0301.4.5.VwJ9qB&s=p
Excellent guidance on how to get to the heart of the matter more easily 👏
Thanks and I’ve just done one for a family member. The top left nut doesn’t need removing it has large plastic spring clip, so remove the bottom nut, insert your hand top left and down the side and you’ll feel a prong. Push it in and it unclips. Thanks great vid.
S
better than a manual thanks Im tring to do mine right now ;-)
Thank you for tutorial.
Super přesně tohle jsem potřeboval vidět, dík
Is this the same thing for an estate
Hi did you find out if its the same? I've an estate
Mondeo station mk4.5 is a bit different. Remove screws from opening latch. Remove plastic cover from inside. Remove 2 M6 nuts left en right from the inside. Unhook the panel in the center from the inside. Then remove the panel with the Ford logo from outside. From there procedure is self explanitory. The disconnect electritycable from the lamp use a screwdriver to depress the protection.
Yep, I tried to pull off the tailgate release panel above the number plate as per the video, thinking I just had to pop a few clips, well something popped and it wasn't the clips, I broke both mounting brackets, nightmare repair gluing that back together.
@@spookbok When using glue, using baking powder where you cant see it or use some fiber with epoxy. Isuggest google or youtube baking powder with superglue.
The biggest problem was the very thin section of the brackets. Once the glue was on I couldn't locate the correct position by feel. Usually broken surfaces will lock into place but that was not the case here. Interesting tip about the baking soda. I used 2 pack epoxy which has worked very well.
super....dziękuje Big thanks
Spot on thanks!
How do I put back the cover for the number plate lights? Is there a trick?
Very helpful thank you
Ak som spravne pochopil, tak ked chcem vymenit ziarovku na spiatocku, tak musim vykonat tento cely ukon ? Neexistuje nejaka lahsia finta ?
Ďakujem veľmi pekne! Tunix munix! :) Danke schön! Thank you very mutch! Hvala! Köszönöm! Mercy!
Pozor!!!U mk4 kombi je to trochu jiné.Pro sundání lišty se znakem Ford je potřeba vyšroubovat dva šrouby u osvětlení registrační značky.Poté sundat tapec dveří a odšroubovat další dva šrouby.Každý na konci lišty.Je lepší sundat i rámeček registrační značky pro lepší manipulaci.Zbytek je stejný jako na videu.
Dik za info akurát dnes to idem menit :D
a kua aj tak som urval právu stranu nakoľko tam dajú železný šrob ktorý zhrdzavie ....
what kind of bulb does it take ?? 😁
Just when I think I know the differences between the Mondeo and Fusion...I just realized the entire rear window and trunk lid lifts up.
how did you remove the first part? any screws from the inside? i try to remove mine and it wont move att all. removed 2 screws near the doorhandle.
Hi, if you mean first part where is Ford logo there are only 4 clips and not any screws (you may see it when I remove cover, those blue clips inside), you need to pull it, on each side there is small ear where is this plastic cover gripped, you need to unhook it.
@@michalorlicek6057 i will try it. Thank you!
What's the solution please? I'm struggling to get it off too
On my MK4 accessing the lights from inside boot lid I was not able to remove the clear reverse light bulb at all but the other smaller T10 501 bulb can be removed without full tear down. There doesn't seem to be enough clearance to remove reverse light bulb. Is there any way of removing that reverse bulb without having to remove the whole cluster like in the video? Then install smaller brighter led bulbs which will allow you to remove the bulb without having to tear the whole back apart. Especially those blue clips from the start they broke on mine.
I needed to remove whole light as my led was broken, but if you need to remove only clear reverse bulb and there is not space through small back plastic cover, you probably need to remove whole plastic cover inside of trunk, it should be enough space to replace that bulb
@@michalorlicek6057 ohhh cheers didn't think of that way instead of the outside tear down. It is quite annoying that they designed consumable parts of the car to be very difficult to access. Might give it a go but first going to look for some small leds of the same style that may help in future light removal.
@@michalorlicek6057 Ive found on a forum someone mentioned they removed two nuts holding the light housing from incide and just pushed it slightly. This way the ear didn't break and they were able to remove the reverse light. However they could not put the light back in so removed the whole back as you did 😃 I'm thinking if I find a smaller p21w led bulb it might be possible to remove after initial strugggle the led bulb easier in the future.
Świetny film, dzięki! Problem mam ze złożeniem elementu do którego przyczepiona jest tablica rejestracyjna. Pomiędzy plastikiem a metalowa częścią klapy zostaje dość duża szpara. W jaki sposób mogę dopasować ten element?
All this just to change a reverse bulb is madness 🤦♂️ thought it was a 2 second job like it was on my old passat.
May get a garage to do it for me as i will undoubtedly break a clip when trying
Hats off to the designers for making it so easy to change a bulb :/
To change a blulb only thing you need is to take off the plastic cover in rear hatch. Than access to all side-bulbs is easy and simple.
@@manaszk Get your facts right before making yourself look silly. Yes, SOME of the bulbs can be changed in this way, but NOT the reverse bulbs.
It is mondeo 2007-2011 ?
MK4.5 2011-2014 (in the UK at least)
Thank you Michal :-)
how to replace third brake light mk4 mondeo
Do you have to outer assembly removal?
Yes, as inner tail light has ear which is behind plastic back panel where is plate, see here: www.aliexpress.com/item/1Set-2Pcs-Inner-Outer-Rear-Lights-Tail-Lights-Taillamps-Right-Side-for-Ford-Mondeo-Fusion-2011/32828169232.html?spm=2114.search0301.4.5.VwJ9qB&s=p
👍🏼
👍
???Why ??? What for??? Remove only lamp and finished the mission ))
Couldn't take ligh out without outer disassembly;)
@@michalorlicek852 Mine was leaking, so thanks for the movie.
EDIT: oops. Correct it is a MK4.5 my bad
Nope defo a mk4
Nope, it's a MK4.5 i.e. facelift MK4.