Sir ye subwoofer filter ko mai direct subwoofer ke joints pr solder krke use kr skta hu??? i am using tda2030 ic with subwoofer input like ye filter ko subwoofer ke + - or jo tda2030 ic ke subwoofer output ki two wires hoti h uske sath isko connect krke will it work???
@@TechTalkSwarup bro pr mujhe lgta h 2030 board is not upto the mark 4" subwoofer 35watts nd (10+10watt satellites speakers) within 2 months usage eik side 1ic stopped working..and full volume pr bass gayab ho jaati h..isme..and a lot of huming while connecting on bt module..
Change the damaged ic asap otherwise the other ics will also stop working. If you are using the usb port present on your ampifier to power the bluetooth adapter then it will cause weird noise, to avoid the noise use a different power supply( preferably old mobile charger) for the bluetooth.
this is good, I am searching for weeks now, others I don't understand, can I use this for my system? amplifier is 360wrms output subwoofer is 12 inch 4ohms single voice coil, can I use your 1k resistor and 1uf 50v filter? thank you in advance..greetings from the Philippines..
Amplifier ke left input me ye circuit lagayenge to left speaker output me subwoofer lagana porega or right input me lagayenge to right speaker output me.
@@TechTalkSwarup what i actually meant ws... i hv sony 4100 5.1 1000 watt rms.. which is not that much loud as compare to other 1000 watt rms 5.1 speakrs
SiI I belong to Tamilnadu. I dont know hindi. Hence it will be useful if you provide running descriptions or directions is English at the bottom of the screen,.
Kya hum non-polar capacitor use kar sakte hai? ...aur kya ne isse Ahuja BTZ- 10000 500W +500W amplifier me use kar sakta hu ..koi problem to nahi hoga na?? Pls help
Take two 1 k resistor then connect one end of each resistor together...and connect each input channels to the other ends of the resistor.. Thats how stereo input is given..
Agar aapke amilifier me 2 speaker out put hai to.. Ek channel ke input me Low pass filter doriye or us output me woofer joriye .. Aur dusre channel output me 2 speakers ko parallal connection me jor dijiye agar yo 8 ohms ke hai to... Aur agar 4 ohms ke hai to series connection me jodiye..
Sir help me I am not getting clean sound in my speaker what should I do I am using tpa3110 amplifier module with 24 watt dc 2 amp dc adapter and 2. 4 ohm 20 watt speaker my sound is not clear please help me sir how can I fix that
The output should match power input.. You are supplying 24 watts. Your board can supply 30 watts at 4 ohms. Use 30 watts power supply to get full performance.
For 125 hz .. mathematically you'll need 1.2k ohms & 1 microfarad, 130 ohms & 10 uf etc resistor and capacitor respectively . But cautious, the audio strength will diminish. Recommended to use active low pass filter instead.
Thank you so much.. ❣️ Can we make a higer gain op amp using transister(12v single supply) with this circuit ? If it is possible please make a vdo on it😁🙏
Hi Swarup, thanks, with your process I successfully converted a singing active Subwoofer to a decent one. But some midrange still creeps into the sub. Hence my question, if want to drop the HPF to 80Hz or below, what should be the combination of resistor & capacitor please? FYI, it is a Pioneer S-51W subwoofer (150W, 10"cone), it does not have a LPF regulator. I'm using your filter solution on the input line to the sub.
One of the combinations would be 1 uf capacitor and 2k resistor for 80 hz. But the audio signal will decrease significantly as you decrease the frequency. I would suggest you to use a active low pass filter in spite of this passive filter. Check out the last uploaded video on my channel on active LPF.
@@TechTalkSwarup Thanks. I'll try the passive option first, because I'm not too worried about signal strength. It's a 150W Pioneer amp after all & I can't increase volume past a quarter, adding another k of resistance means I'll have to turn up the volume a bit more.
@@TechTalkSwarup so this is gonna sound weird but, i want a low pass filter that will only receive frequencies below 19 KHZ can you tell me what resistor i should use? thx
Hi. I have zero knowledge in all this. I need help with reducing low frequencies (bass) in my subwoofer. Unfortunately it doesn't have a bass control. Please help. Thank You.
If you want to add pre-amp board , you can simply connect(left, right, ground) the output of the pre-amp board to the input of your sound system. And give audio input to the pre-amp board..
Na.. 4558 ic er moto oto valo bass hoy na.. Kintu jodi board a bass treble control theke bass barano hoy tahole ai bass filter ti jothesto valo kaj kore..
Why does it work? I am no electrician but after some search with google I learned that a capacitor in an AC circuit should have a higher resistance with lower frequencies and a lower resistance with higher frequencies. Wouldn't that mean, that a capacitor works as high pass filter?
Bhai mere pass 1 intex ka 4.1 home theatre hai usme mene sony ka subwoofer extra add kar diya hai koi problem to nahi hogi na bina kisi equipment ke please reply
hi, I want to make a subwoofer, 8" bass only,,, I want high deep surface vibrating sound,, I dont have any amplifier.,just a mobile,, and i don't have a budget to buy any amp.. suggest some solution. what can i do under 8-10$???
@swarup sir , 4440 double IC board k liye kaunsa speaker best hai???? Humare idhar YP company ka speaker milta hai ....Kya woh sahi hoga???? Plzzz suggest
Mujhe to nahi pata yp company ke bareme.... but... 4440 ic se max 40 watt mil sakta hai 4 ohms ke load pe... to aap 40-60 watt 4 ohms speaker yea fir 20-30 watt 8 ohms ka speaker use kar sakte hai..a66a rahega....
Which pair should i use? I have 1.2k ohm, 330ohm, 2.2ohm and 9.1ohm resistors and for the capacitors i have 4.7nf, 47nf, and100nf capacitors. Now i have a 1nf capacitor but it doesn't have any positive or negative marking so i don't know the polarity
I used the parts specified and connected as directed I believe bass is coming through however it is very very low can you advise how to get it louder. The speaker i am using is 6 ohm
For that connect this filter to any of the input channels and leave the other channel input untouched or you can add another high pass filter and connect it to the untouched input...
4558 ic usually audio input me use hota hai only bass output ke liye. Agar aapke board me 4558 ic hai to subwoofer ka line pehele se hi hai... Is circuit ka use karne ka jarurat nahi hai..
Sorry mere pass abhi ye kit nahi hai... Aap input line se input na de kar Ic ke 7 number or 10 number pin me direct audio input dijiye... Kiu ki agar input line se denge to wo filter ho kar ic me jati hai..
Aap jo kisi bhi amplifier me ye filter add kar sakte hai... Is filter ko input line me install karna parta hai,,, jitnebhi watt ka amplifier ho usse koe farak nahi parta hai...
I was searching for this very long and finally got it, I am using same 3055 and I have 2 subwoofers (4 inch each) and 2 speakers how to make all work, please help?
As 3055 has only 2 channels.. You have to connect 2 speakers per channel... If the speakers are of 8 ohms ,, connect them in parallal mode.. And if the speakers are of 4 ohms connect them in series mode... That would do..
1.does it work with pam 8403 audio amplifier to power up the 3watt 4ohm speaker ? 2.will it burn the speaker at high volume? 3.from how much frequency to which frequency it provide to the amplifier? plz ans the question..........
@@TechTalkSwarup sir 🙏 aap bahut achhe ho 🙏 . Sir mein paramount pmt- 51 5 band ka radio 📻 use karta hu. .. Esa kya kiya jaye ki radio me light bijli ka effect kam pare . Aur kir - kirane ki awaaz kam ho jaye. Aur radio me bass kese banaya jaye. Aap jo video banate ho . Esi video kahi nahi milti .
Yes u can use a 4.7 uf or 0.1 uf capacitor... In case of 4.7 uf capacitor u have to use 200 ohms resistor instead of 1k resistor.. And in case of 100 nf capacitor you have to use 10k resistor.
Sir ...mera 5.1 channel home theater me 5 speaker ko tweeter ke jaise sound nikal na chahta hu. . . . Uss ke liye kya kru ...please help me. .ya fir koi video banao.... main reply ka integrr me hoon.....
Uske liye iss video me jo capacitor use kiya hai uski jaga 5.6 uf ka capacitor use kijiye.... Sorry.. samne mera exam hai to mai filhal koe video nahi bana sakta... Ye circuit kam karta hai hi nahi mujhe jarur bataeaga...
Capacitor kitnevi volt ta le sakte hai...bus 5.6 uf hona chahiye.. uf jitna barhega frequency bhi unta barhega... Resistance 1 k ohms 1/2 watt ka use kar sakte hai..
you must use this before amp right? It does not work directly like this : Input - Circuit - Output, correct? Cause I tried with no results, all I got was really low sound like 5% of what it used to sound.
@@TechTalkSwarup Earlier you replied for my query that this filter comes before the amplifier which is an active filter. Thats why I specifically asked for a passive one.
the reason you heard voice was bcz the filter is of 1st order and the cut off is not that great... u can make 3 pairs of these and connect them together in same order (in series) and there will be no voice, only bass.
Very Impressive , this is what I have been searching for a long time
Thank you..
@@TechTalkSwarup bhai lekin ye BT me work nhi krta...Kuch solution hai apke pass
@@TechTalkSwarup thanks a lot
Sir vocal kit any video ??
I'm very sorry... my exams r going on..
Free hone par video upload karunga..
Sir ji. Mene radio me. Aap bataye anusaar radio 📻 ke speaker me capacitor lagaya to wo bahut achaa kaam kar raha. Nice 👍
Sir ye subwoofer filter ko mai direct subwoofer ke joints pr solder krke use kr skta hu??? i am using tda2030 ic with subwoofer input like ye filter ko subwoofer ke + - or jo tda2030 ic ke subwoofer output ki two wires hoti h uske sath isko connect krke will it work???
Nahi usse kam nahi karega.. Is circuit ko amplifier ke input line mehi lagana parega...
@@TechTalkSwarup bro pr mujhe lgta h 2030 board is not upto the mark 4" subwoofer 35watts nd (10+10watt satellites speakers) within 2 months usage eik side 1ic stopped working..and full volume pr bass gayab ho jaati h..isme..and a lot of huming while connecting on bt module..
Change the damaged ic asap otherwise the other ics will also stop working.
If you are using the usb port present on your ampifier to power the bluetooth adapter then it will cause weird noise, to avoid the noise use a different power supply( preferably old mobile charger) for the bluetooth.
Accha laga,aapka yea filte kinte se kitna waat speeker ke liye accha kaam korega?
Sab me kam karega...
this is good, I am searching for weeks now, others I don't understand, can I use this for my system? amplifier is 360wrms output subwoofer is 12 inch 4ohms single voice coil, can I use your 1k resistor and 1uf 50v filter? thank you in advance..greetings from the Philippines..
Yes.. you can use this with your amplifier.. no problem....
Worck perfectly thanks for not scamimg people
You are welcome...😊
Bro will it work on small 5v baord and driver?
Yes.. it will work on any board
@@TechTalkSwarup Thanks brother 😄
sir ek baat bataiye, kya aap ek baar circuit dia de sakte hain? mujhe vocal speaker aur subwoofer kaunse channels me kai lagenge samajh nhi aaya
Amplifier ke left input me ye circuit lagayenge to left speaker output me subwoofer lagana porega or right input me lagayenge to right speaker output me.
Can we use 2.2uf capacitor
If you use 2.2 uf capacitor then you as well need to use 450 ohms resistor to match the desired frequency..
Do this works if I connect this circuit to speaker wire.i mean right before the speaker inputs??
No.. this circuit is for audio input line only not in speaker output...
Can I wire this up like this
Amplifier output --> This circuit --> Speaker
Is this possible?
No... of course not... with this circuit this is not possible..
For this you need to use a different circuit
...
@@TechTalkSwarup What circuit is that?
@@trustnt1337 low pass filter for input side
Your circuit works like a charm. Awesome work bro, saved a lot of money for me. Thank you Swarup
Can we increase home theater sound output
For increase . You can replace the transformer to a 1amp more one. Or add capacitor to the power supply Or change to a better speaker.
@@TechTalkSwarup what i actually meant ws... i hv sony 4100 5.1 1000 watt rms.. which is not that much loud as compare to other 1000 watt rms 5.1 speakrs
SiI I belong to Tamilnadu. I dont know hindi. Hence it will be useful if you provide running descriptions or directions is English at the bottom of the screen,.
Okey 👌.. subtitles will be added soon...😊
I mean how to cut hi and mid is there any tricks
Can i use this in TPA3116D2 amplifier? Thanks in advance!
Yes.. in any amplifier.
Kya hum non-polar capacitor use kar sakte hai? ...aur kya ne isse Ahuja BTZ- 10000 500W +500W amplifier me use kar sakta hu ..koi problem to nahi hoga na?? Pls help
Bro if I connect both of chanels with 2 serkits and connect both with subwoofers and use another 8610 amplifire for sound
what hepend
Take two 1 k resistor then connect one end of each resistor together...and connect each input channels to the other ends of the resistor..
Thats how stereo input is given..
Thanks good circuit it is working and my first impression is like this 😲😲😉🤯
😇
Kya mai 1.5k ka resistor use kar sakta hu plz reply🙏🏻
swarup sir mera 1question hai ke, aap ke pass home made 1sub aur 2speakers hai to usko kaise aur kanha se jode taki best sound sub se mile
Agar aapke amilifier me 2 speaker out put hai to..
Ek channel ke input me Low pass filter doriye or us output me woofer joriye ..
Aur dusre channel output me 2 speakers ko parallal connection me jor dijiye agar yo 8 ohms ke hai to...
Aur agar 4 ohms ke hai to series connection me jodiye..
My amplifier is 2.0 channel. I dont want to use crossovers. But can i run 4 ohm 90 watt speaker only for bass?
Yes you can.....
Can I solder it directly to the speaker ?
No.. only in input connection.
you are genius bro i love you from heart😘😘😘😘😍😍😍
Thank you!!
Sir how can I reduce bass in my Philips home theatre spa8000b,no bass settings given
Find the audio input line for the bass ic and add an potentiometer there.
Watch the video on Active low pass filter on my channel. That would help.
Excellent boss you are proven following you
Sir help me I am not getting clean sound in my speaker what should I do I am using tpa3110 amplifier module with 24 watt dc 2 amp dc adapter and 2. 4 ohm 20 watt speaker my sound is not clear please help me sir how can I fix that
The output should match power input..
You are supplying 24 watts.
Your board can supply 30 watts at 4 ohms.
Use 30 watts power supply to get full performance.
I want to make below 125 hz low pass filter...so.. which value of resistor and capacitor should I use
For 125 hz .. mathematically you'll need 1.2k ohms & 1 microfarad, 130 ohms & 10 uf etc resistor and capacitor respectively .
But cautious, the audio strength will diminish. Recommended to use active low pass filter instead.
Thank you so much.. ❣️
Can we make a higer gain op amp using transister(12v single supply) with this circuit ?
If it is possible please make a vdo on it😁🙏
It's 100% Working
But I Want Only Voice Circuit Please Bro I'm Waiting Your VidEo
Check out the video named "POWERFUL low pass filter" on my channel...
Move to the time 4:32 . There i'v used a high pass filter for only voice.
Hi Swarup, thanks, with your process I successfully converted a singing active Subwoofer to a decent one. But some midrange still creeps into the sub.
Hence my question, if want to drop the HPF to 80Hz or below, what should be the combination of resistor & capacitor please?
FYI, it is a Pioneer S-51W subwoofer (150W, 10"cone), it does not have a LPF regulator. I'm using your filter solution on the input line to the sub.
One of the combinations would be 1 uf capacitor and 2k resistor for 80 hz.
But the audio signal will decrease significantly as you decrease the frequency.
I would suggest you to use a active low pass filter in spite of this passive filter.
Check out the last uploaded video on my channel on active LPF.
@@TechTalkSwarup Thanks. I'll try the passive option first, because I'm not too worried about signal strength. It's a 150W Pioneer amp after all & I can't increase volume past a quarter, adding another k of resistance means I'll have to turn up the volume a bit more.
Yes.. then. You are welcome..
@@TechTalkSwarup so this is gonna sound weird but, i want a low pass filter that will only receive frequencies below 19 KHZ
can you tell me what resistor i should use?
thx
3.8 ohms resistor and 2.2 uf capacitor. For 19 khz.
Sir. 🙏🙏 radeo me. Radio ke speakar me capacitor laga sakte he 🙏
Is circuit ko audio input main lagte hai.. speaker main nahi...
Sir iss filter ko kya me 5 volt audio amplifier me use karsakte hai...
Ji .. kar sakte hai..
Hi.
I have zero knowledge in all this.
I need help with reducing low frequencies (bass) in my subwoofer. Unfortunately it doesn't have a bass control.
Please help.
Thank You.
Which amplifier board r u using?
@@TechTalkSwarup
I dont know.
My speaker is SONY SA-D40 80 W
I want to add pre amp in it somwhow.
If you want to add pre-amp board , you can simply connect(left, right, ground) the output of the pre-amp board to the input of your sound system. And give audio input to the pre-amp board..
Can i use variable resistor (preset) at the place of resistor
Yes...
Kya mai 1.5k ka resistor use kar sakta hu plz reply🙏🏻
@@Blackplayz5643 han Bhai
Hey..can you show how to make this adjustable?
hello mr
i hope this is not too late
you just connect potentio input from out that filter and connect the potentio out to you amplifier
hope this help
sir ye formula stk 4392 me chal sakta he?
Ha. Chalega.. sabhi audio amplifier board me kam karega...
U r genius this one is best for bass filter on 4440 . Please viewer try it at once today I have got perfect bass filter without using 4558
Thank you..
सर मेरे पास TPA3116d2 amplifer हे, WOOFER मे से High frequency sound आता है. Please solution बता दिजीय की सिर्फ bass ही आये.
স্বরূপদা এইটা কি ic4558-র মতই কাজ করবে?অথবা দুটি pf 104j এবং res 33k দিয়ে যেমন bass filter করা হয় এটা তেমন?
Na.. 4558 ic er moto oto valo bass hoy na..
Kintu jodi board a bass treble control theke bass barano hoy tahole ai bass filter ti jothesto valo kaj kore..
@@TechTalkSwarup ,ekta eirakom simple project banan please...
Sir only vocal kit ya ni ki voice ko kam jyada kar sake aisa koy kit banaye
Why does it work? I am no electrician but after some search with google I learned that a capacitor in an AC circuit should have a higher resistance with lower frequencies and a lower resistance with higher frequencies. Wouldn't that mean, that a capacitor works as high pass filter?
The capacitor works as a low pass filter here. It would also act as a high pass filter.
If you wire the cap in series, it's a high pass. In parallel, however, it functions as a low pass filter.
Is it working good? Will not I burn the woofer? Can I use it in a 60 watt 6ohm speaker?
Its working..yes you can use it in a 60 watt 6 ohm speaker.
Sir kya mai 1k ke gagha 1.5k resistor use kr sakta hu?
160 hzs frequency ke liye 1k hi use karna parega...
Bhai mere pass 1 intex ka 4.1 home theatre hai usme mene sony ka subwoofer extra add kar diya hai koi problem to nahi hogi na bina kisi equipment ke
please reply
Ye depend karta ki aapka hometheater kite ohms tak jhel sakta hai....
Agar woofer ka ohms load jada kam ho gaya to jada der chalne se ic jal jayega..
hi, I want to make a subwoofer, 8" bass only,,, I want high deep surface vibrating sound,, I dont have any amplifier.,just a mobile,, and i don't have a budget to buy any amp..
suggest some solution.
what can i do under 8-10$???
Cant be it placed at speaker terminal?
No.. the capacitor may explode.
Darun swarup da.eta khub helpful video
But ekta 4558 ic diye banio tomar exam er por please
Ha..nischoi...
Omg thank you so much👏🏻👏🏻👏🏻👏🏻
Where to connect it in 4440 ic board.. Plz reply ur fan
My pleasure..
Connect it to the audio input line of the board.. to left or right input and the ground connection.
Can it be used as post amplifier low pass filter
No.. its a pre circuit...
So I can use this setup instead of inductor?
Yes...
Inductors are used at the output.. this circuit is used at the input
@@TechTalkSwarup thank you
@@TechTalkSwarup question. I have a 60-8000hz speaker bot I wanna bring the 8000hz to 3000hz what Inductor should I use ore what setup you recommend?
I'd suggest you to use a passive rc high pass filter at the input.
Use 0.02 uf capacitor and 2.6 ohms resistance.
@@TechTalkSwarup thanks
Sir pam 8403 me base ke liye kitne uf ka capacitor use karna padega?
@swarup sir , 4440 double IC board k liye kaunsa speaker best hai???? Humare idhar YP company ka speaker milta hai ....Kya woh sahi hoga???? Plzzz suggest
Mujhe to nahi pata yp company ke bareme.... but...
4440 ic se max 40 watt mil sakta hai 4 ohms ke load pe... to aap 40-60 watt 4 ohms speaker yea fir 20-30 watt 8 ohms ka speaker use kar sakte hai..a66a rahega....
@@TechTalkSwarup sir , kaunsa company & kitna inch k ac6a hoga ? aur usme bass bhi aye a... Please suggest me😑
Aap local company use kar sakte he koe problem nahi ...
Aap 6 inch ka ek woofer ya subwoofer or 6-8 inch ka speaker le ligiye....
Which pair should i use? I have 1.2k ohm, 330ohm, 2.2ohm and 9.1ohm resistors and for the capacitors i have 4.7nf, 47nf, and100nf capacitors. Now i have a 1nf capacitor but it doesn't have any positive or negative marking so i don't know the polarity
no suitable pair can be made with the mentioned components, to filter 160 hz.....
If you use 100nf capacitor than use a 10 k resistor.. that will do.
Sir if i use this filter and use the amplifier with my pc ..is it harmful for my pc??
Not at all.. its safe..
What value resister is used
1k resistor...
I used the parts specified and connected as directed I believe bass is coming through however it is very very low can you advise how to get it louder. The speaker i am using is 6 ohm
U can add an operational amplifier with this circuit to boost input signal..
As described in my last uploaded video.
you also need to place it after the pre amp
What will happen when I use 2K register , it may decrease the frequency response like 60 hertz to 50 Hertz ??
No... the resistor is mainly used to protect the music input-er device..
If you use 2k resistor that will decrease the sound
Ok but can you suggest any other idea or trick to get the frequency response 50hz to 60hz for good quality low frequency sound
Of course, but i'll let u know after testing...
I don't want to misguide anyone.
Thanks sir for your reply , I am just waiting for my dream project of 12 inch subwoofer
Make such videos more because your videos are quite impressive and easy 🤗🙂🙂
How about the left chanel is all bass and the rught chanel is more vocal?how to connect??
For that connect this filter to any of the input channels and leave the other channel input untouched or you can add another high pass filter and connect it to the untouched input...
Bai resistor ka colour code bta do plzzzz nd i subscribed u for a such simple video
Broun black red
@@sarojdevi1135 thanks brooo 🙏🙏🙏🙏
Can we connect this Circuit to output line?
No.. this circuit is made for input line only...
MERE PAAS 4558 double ic wali board Hai to ise connect se ek taraf bass aur ek taraf sound Niklega kya please reply me please
4558 ic usually audio input me use hota hai only bass output ke liye.
Agar aapke board me 4558 ic hai to subwoofer ka line pehele se hi hai...
Is circuit ka use karne ka jarurat nahi hai..
@@TechTalkSwarup kha PAAS hota Hai please bta do bro I subscribe your channel
Sir kya hm is filter ko pam 8403 mai use kr skte h
Ha kar sakte hai....
Sir mena avi kia tha
@@TechTalkSwarup but mera hua ni sir plz bna do ek vdio
@@TechTalkSwarup plz sir help me
Sorry mere pass abhi ye kit nahi hai...
Aap input line se input na de kar
Ic ke 7 number or 10 number pin me direct audio input dijiye...
Kiu ki agar input line se denge to wo filter ho kar ic me jati hai..
It is really good and working 😀
If connect audio in ok to amplifier or direct connection to board replay bro
If your amplifier has a pre-controller installed then it may not work.. in that case you must connect this circuit to the input of the board directly.
15w k.. Amplifier m.. Kesa kaam krega mene try kiya h.. 50*2 watt k.. Amplifier m.. Pr ye filter 15w k.. Amp m.. Acha output dega?
Aap jo kisi bhi amplifier me ye filter add kar sakte hai...
Is filter ko input line me install karna parta hai,,, jitnebhi watt ka amplifier ho usse koe farak nahi parta hai...
Wattage to km nhi hoge na?
wattage same rahega..
@@TechTalkSwarup bs sukriya
Agar 1uf ka capacitor na mile to kitne uf ka use kar sakte hai?plzz reply
10 uf use kar sakte hai par uske liye 100 ohms ka resistor use karna parega...
I was searching for this very long and finally got it, I am using same 3055 and I have 2 subwoofers (4 inch each) and 2 speakers how to make all work, please help?
As 3055 has only 2 channels..
You have to connect 2 speakers per channel...
If the speakers are of 8 ohms ,, connect them in parallal mode..
And if the speakers are of 4 ohms connect them in series mode...
That would do..
1.does it work with pam 8403 audio amplifier to power up the 3watt 4ohm speaker ?
2.will it burn the speaker at high volume?
3.from how much frequency to which frequency it provide to the amplifier?
plz ans the question..........
1. It will work on any amplifier..
2. Of course not... cause it only filters the frequency..
3. The frequency barrier is around 150 hz.
@@TechTalkSwarup tq very very much......for reply quickly
Bro 1miu extra capacitor100 Miu chalega
150 hz paneke liye 1 uf ka capacitor hi use karna parega....
Agar 100 uf use karenge to 10 ohms ka resistor use karna parega
Sir clear trable lene ke leya kon circit use kar saktay hnn
I like to connect audio in rc pin is it ok this circuit
Works perfectly, have tried and confirmed! Thank you!
Mine doesnt work for some reason maybe i need a smaller resistor idk?
In some class d amplifiers or in some pre-amps it might not work.. in that case use an active low pass filter. Video is available on my channel.
I have 4440 double ic stereo full board can i do this in that?
Yes you can...
Hey guy well done, God bless.
Bhai dj ke liye bass ke liye koi or dasu he kya
Sir ji 🙏 bahut khoobsurat video banate ho 🙏 . Sir radio 📻 ki aawaz Cealiar saaf kase laaye. .. Video
Kya ye 4558 se achi bass deta he
Sir aap ki har video bahut achhi hoti he 🙏 ek video radio par bana do
Thank you 😊.
Radio par konsa video chahate hai.?
@@TechTalkSwarup sir 🙏 aap bahut achhe ho 🙏 . Sir mein paramount pmt- 51 5 band ka radio 📻 use karta hu. .. Esa kya kiya jaye ki radio me light bijli ka effect kam pare . Aur kir - kirane ki awaaz kam ho jaye. Aur radio me bass kese banaya jaye. Aap jo video banate ho . Esi video kahi nahi milti .
Does connecting speakers in series increase their watts. For example I am having two 25 watts speaker connected in series will they become 50 watts.
Yes... if you connect speakers in series their resistance will increase. And they will be able to take in more power without burning.
Thank you brother.
Can i use 240ohm resistor with 4.7uf capacitor. Please tell me
Im your new subscriber.😊😊😊
Glad to know..😊..
Yes you can use that... with this setup you'll get 140 hz.. which is slightly less than 160 hz as instructed in the video..
Friend when i setup this connection then a loud beep voice is coming from speker
What can i do for this
Which amplifier board or ic are you using? R you following the each steps exactly shown in this video?
Yes i have followed each and every step, but still it is.
Borad me wiring kha paas krana hai speaker vire hota hai wha paas kya please reply me
Board me jaha audio input line hota hai waha iss circuit ko jorna hai..
Thanks
I am searching this for long time
क्या हम USB MODULE में भी left या right में bass sound के लिए उपयोग कर सकते हैं
Ha.. jarur... koe problem nahi..
@@TechTalkSwarup Thanks
Welcome..
can i use it 20v 100Watt class d amp..?
Yes... u can
@@TechTalkSwarup thank you
that wouldnt affect the other tapped speakers? only woffers?
In which audio channel u would connect this circuit, it would affect only that channel..
Other channels will have no affect..
Can i use 4.7 uf capacitor or "104 " Capacitor 0.1uf?
Or can i use 3 pcs 4.7 uf capacitor in series..to make value in 1.5uf .. It is okay i use that?
Pls relpy new subscribers here
Yes u can use a 4.7 uf or 0.1 uf capacitor...
In case of 4.7 uf capacitor u have to use 200 ohms resistor instead of 1k resistor..
And in case of 100 nf capacitor you have to use 10k resistor.
Yes that would work as well.
@@TechTalkSwarup thank you very much sir.. ☺
What is its use ?
Sir ...mera 5.1 channel home theater me 5 speaker ko tweeter ke jaise sound nikal na chahta hu. . . . Uss ke liye kya kru ...please help me. .ya fir koi video banao.... main reply ka integrr me hoon.....
Uske liye iss video me jo capacitor use kiya hai uski jaga 5.6 uf ka capacitor use kijiye....
Sorry.. samne mera exam hai to mai filhal koe video nahi bana sakta...
Ye circuit kam karta hai hi nahi mujhe jarur bataeaga...
@@TechTalkSwarup
5.6 uf 250 v capacitor and resistance kitna watt and kitna ohm lagayenge please. ..bataye..?????
H.S Exam ???
Capacitor kitnevi volt ta le sakte hai...bus 5.6 uf hona chahiye.. uf jitna barhega frequency bhi unta barhega...
Resistance 1 k ohms 1/2 watt ka use kar sakte hai..
B.a. Final year exam
Many many thanks.. Naam se lagta h bangali ho..? ?
you must use this before amp right? It does not work directly like this : Input - Circuit - Output, correct?
Cause I tried with no results, all I got was really low sound like 5% of what it used to sound.
Before amp.
How can i do this if i have an cerwin vega 18 inch subwoofer with active crossover? I want only low frequencies.
Does your sound system have a audio input line or aux line?
Then you should install this circuit at the audio input wire...
TechTalk Swarup yes it does. I’m driving the subwoofer with a crown amplifier.
4.7 uf ka capacitor laga skte kya
Yes you can use 4.7 uf capacitor in this circuit..
But the cutoff will be about 35 Hz....
And that would not be that suitable for music. I think.
What happens if I use 0.33 uF capacitor
Then the frequency will be changed to 480 hzs.. if you want to keep the frequency same then change the resistor also , to 3k..
very cool I'm gonna try this
super cool! I understood even when I do not speak hindi :-) but how to "merge" left and right to 1 woofer?
Thank you...
That depends on which amplifier board you are using this...
If your amplifier supports bridging then you can merge the channels..
Do you have a passive filter for 150 \ 200Hz?
The circuit i have shown in the video is a passive rc low pass filter.. and its cut off is 159 hz..
.. do you mean passive Band pass filter?.?
@@TechTalkSwarup Earlier you replied for my query that this filter comes before the amplifier which is an active filter. Thats why I specifically asked for a passive one.
How is bass?
Better than my expectation..
How to add in dd free dish amplifire
It works nice..but the circuit didn't give enough pure bass....still the voice can heard
Please make it better without using any IC.
Thank you 😊
I would be working on that and upload video after by exam...
the reason you heard voice was bcz the filter is of 1st order and the cut off is not that great... u can make 3 pairs of these and connect them together in same order (in series) and there will be no voice, only bass.
You're better off using a choke in series instead of a cap.
If i put 3 pairs of these filter in series, i would get only bass on the output?
It may work.... u can try..