I spend 39 yrs in glass industry in Dubai ....we had glass cutter from mp India, Mr nooral he was uneducated, but never seen glass cutter like him, who can beat intermac waterjet machine whc can cut any shape or thikness, he use to say bhai sahab Mai glass kattata nahi khata hu,. Means i don't cut glass i eat glass, seen him cutting any thickness....any shape like child plays with scissors cut paper.....great born talent
One of the things novices do when cutting glass is using too much pressure with the cutting tool. You know when you have done it right by the sound. It should be a light hiss and the score is a fine line , almost hard to see. Too much pressure and the sound is crunchy with score looking like a deep scratch. The deep scratch are tiny fractures running radially from the line and at best will result in a rough cut and at the worst not cutting at all or running everywhere but where you wanted the cut. Also make sure you have cleaned the glass first and the cutter is not nicked and/or dirty. My humble experience.
Thank you, I was able to cut to size a thick mirror following your technique using the hammer. A bit unerbing but it worked!! Great simple way of cutting very thick glass with simple tools, down to earth. I really like that, just using your hands, even wearing sandals 😊 Some people get over killed with so much gear and tools. From all the videos I watched, this was the most helpful. Thsnk you
jugaad technology: Thank you for this video. I see now that it is important to develop a "feel" for how hard to tap. This technique allows people to cut glass with simple tools and a little patience and perseverance. Thanks again for sharing your high level ninja glass cutting knowledge. 😊
Been cutting glass for 42 years now and thicknesses up to 19mm by hand and only time I used a tapper was to start the scores of 10 and 12mm circles. Never on straight lines.
1. use more big table to cut 2.after the first hit by hammer you use that pen under the cuting line 3.push down the glass ......then the cuting line more smooth than this
When I was kid we used to to the same, but we made sure both ends were tapped fist, then we used to tap o the middle. That way we would guarantee the cut would be uniform end to end.
Just Use a brush to apply the oil on the glass before you cut it with the glass cutter and then place the sodden back part of the brush under the glass on the end of the cut and snap it pushing down.
@@johnbernardvillamarin452yes I cut really big sheets of thick glass (3/8”) like that at my shop! There are a few ways that work nicely and this is just one of them!
That would be risky when tapping a large piece which would fall because of its weight. A support would be needed on both sides of the glass, and a ball pen hammer would have been better because of the round head as it would give softer taps, thinner glass can just be snapped after one tap to run the line, Thank You
IF it was a large piece, but it wasn't. The fact that the guy's made his own hammer from re-bar says to me maybe he doesn't simply have access to a plethora of tools so he makes do (& well) with what he has.
I tried this method several times on a Shower Glass 3/8” but the Glass won’t break !!! Any advice ( I have 72” L that I have to cut it to 48” ). Thank you in advance!!!
That's amazing, I just scored a 1/4" piece of glass that won't break, I tried tapping it with the ball on the end of the cutter, I guess I need something heavier to tap it with?
This is also a method of cutting thick glasses ....nothing wrong in it . All methods are almost same only diffrence is how you apply force after scratching the glass .👍👌
May I ask you: If the glass was thinner ( about 2; 3; 4 mm...) , before it broke , we need to knock its face under the glass like you or do we bend it straight down? Thanks for your sharing on how to cut thick glass very good.
Knock the glass only if you absolutely have to... His technique is not that great... Knocking the glass can make the edge very uneven... Your welcome..
That must have been the first time you have ever cut a piece of glass because you did almost everything wrong. I'm afraid I will have to sack your teacher.
I use mineral turpentine for cutting oil for years it works fine as well and cheaper than kerosene have been recycling glass for years much cheaper when doing your own repairs.
I spend 39 yrs in glass industry in Dubai ....we had glass cutter from mp India, Mr nooral he was uneducated, but never seen glass cutter like him, who can beat intermac waterjet machine whc can cut any shape or thikness, he use to say bhai sahab Mai glass kattata nahi khata hu,. Means i don't cut glass i eat glass, seen him cutting any thickness....any shape like child plays with scissors cut paper.....great born talent
Hats off to Mr Nooral...
That's not the good way to cut thick glass.Im a glass cutter for 36 yrs .
Uneducated?
Really!
@@alfredosantiaguel5784 please teach me. I want to learn thick glass cutting Sir. Thanks in advance. 💐😇
No sirve
Техникээ хуваалцсанд баярлалаа.
One of the things novices do when cutting glass is using too much pressure with the cutting tool. You know when you have done it right by the sound. It should be a light hiss and the score is a fine line , almost hard to see. Too much pressure and the sound is crunchy with score looking like a deep scratch. The deep scratch are tiny fractures running radially from the line and at best will result in a rough cut and at the worst not cutting at all or running everywhere but where you wanted the cut. Also make sure you have cleaned the glass first and the cutter is not nicked and/or dirty. My humble experience.
Thank you for the information.
Nope. Too much time just learn from another experienced person
thanks much for your experience leaning something here for you sir_ as a glass man
Thank you, I was able to cut to size a thick mirror following your technique using the hammer. A bit unerbing but it worked!!
Great simple way of cutting very thick glass with simple tools, down to earth. I really like that, just using your hands, even wearing sandals 😊
Some people get over killed with so much gear and tools.
From all the videos I watched, this was the most helpful.
Thsnk you
Thanks. Sounds like Planning and Patience are key.
Hadir nyimak boss ku suksesselalu 👍👍👍
Well done!
jugaad technology: Thank you for this video. I see now that it is important to develop a "feel" for how hard to tap. This technique allows people to cut glass with simple tools and a little patience and perseverance. Thanks again for sharing your high level ninja glass cutting knowledge. 😊
Your are a great crack, thanks so much.
Great job!!😊
Jeez weez, I would not even attempt it. Thank you for your expertise, and for sharing it with us.
I like your cool hand-made hammer!
I have no idea how I got here but this was so cool to watch, clearly a craftsman at work
Been cutting glass for 42 years now and thicknesses up to 19mm by hand and only time I used a tapper was to start the scores of 10 and 12mm circles.
Never on straight lines.
Que usabas entonces en línea recta?
On utilise une equerre et pas une baguette de bois et du petrole ainsi qu une boule a detonner des tutos par des bricoleurs du dimanche .@@OuyaYouyo
1. use more big table to cut 2.after the first hit by hammer you use that pen under the cuting line 3.push down the glass ......then the cuting line more smooth than this
Excelente video
I always say. " you can't control glass but you can tame it." I love my occupation and it seems as if you do too.
بہت خوبصورتی سے شہشہ کاٹ دیا
Thank you for the demo!!
Lovely,👌👌👌👌🏹🎯
Wow that awesome I'm amazed nice n cool jugaad thx for sharing. 😍🌷
Que marca e modelo de cortador vc usa nesse vídeo ?
Brilliant. Thank you so much for sharing.
Thanks so much! Can I use any other type of oil before the cut?
awesome idea it so effective.
I need to do this to a 10mm table top. How do I smooth the edge and make it look neat once the glass is cut ?? Thanks great video 👍🏻
By using belt sanding machine u can make the edges smooth.
What an incredible skill
Thank you for sharing your technique. 🙏🏾
When I was kid we used to to the same, but we made sure both ends were tapped fist, then we used to tap o the middle. That way we would guarantee the cut would be uniform end to end.
Puedes usar un pincel o un vaso he introducir el toyo. asi se lubrica mejor.
Glass cuting ke liye konsa oil use karna hai
Aap kerosene ya diesel use kar sakte ho
Good job
Amazing!!
Cutting glass in sandals… this could turn into a whole different type of video.
Does your technique work for cutting tempered glass? Thank you for sharing your experience.
No, tempered glass cannot be cut without annealing it again.
you cant cut tempered it will brake
could you cut both sides ?? would that be better ?
Cut at one side is better
Good work
Just Use a brush to apply the oil on the glass before you cut it with the glass cutter and then place the sodden back part of the brush under the glass on the end of the cut and snap it pushing down.
I see this technic of the masters ,in the bigest size's,,and it really amazing with sudden loud sound,,,👍☺️🤣🇵🇭it works..
@@johnbernardvillamarin452yes I cut really big sheets of thick glass (3/8”) like that at my shop! There are a few ways that work nicely and this is just one of them!
That"s a nice clean cut, excellent.
I was trying to same glass in small pieces but failed. I will trying your technique. Thanks for sharing
Excellent 👍
Thank you
ruclips.net/video/D0epZC3rxfk/видео.html see my video of glass cutting
Wonderful. Like 👍.
holy crap cutting glass in sandals friggin crazy
Learned something today 🙏
I have a project I'm doing to replace my patio glass. I was curious what should I do to make a center circle cut for my umbrella?
Good job.....
Sir apne kach per line khichte samay kon si liquid dala h batao
Kerosene oil
Beautiful
That would be risky when tapping a large piece which would fall because of its weight. A support would be needed on both sides of the glass, and a ball pen hammer would have been better because of the round head as it would give softer taps, thinner glass can just be snapped after one tap to run the line, Thank You
Why watch a video if you already know everything?
@@christianscustoms6429 That's what we call a dumb question ! Jignesh Tailor's advises are important .
You just earned a dislike .
Turn it over.
IF it was a large piece, but it wasn't. The fact that the guy's made his own hammer from re-bar says to me maybe he doesn't simply have access to a plethora of tools so he makes do (& well) with what he has.
Nice ❤
Will teak oil work for cutting fluid?
Does that work with tempered glass?
No, this trick will not work
U cant cut tempered at home dude
@@shiyamaifrad8933 I found out the hard way.. lol
But can professionals/companies do it or is it just impossible to cut?
@@BlackFaceTrudeau it is not impossible cause u can get custom sizes from companies i guess they cut it with some heavy duty machines
Tempered glass CANNOT be cut. Glass companies cut holes, dog doors, handles etc BEFORE tempering. Do not attempt it as it will explode.
If you scratch both sides of the glass with cutter it will become very easy
Hallo etnha time kathna ma lagha ga to farha to banha gya karegarh
Hi. Can I use sandpaper to smooth the edges?
It is better to use emery stone when u try to smooth edges manually.
Bhai itte der me customer chale gaye ho gye hm 😂😂😂😇
next, teach me how to make hole on the glass. thanks 😊
Please check my other video for drilling hole in glass...
Mantap bos
Giive him a applause......
will this method work with curves?
Yes, but you have to be patient while tapping glass
I tried this method several times on a Shower Glass 3/8” but the Glass won’t break !!! Any advice ( I have 72” L that I have to cut it to 48” ).
Thank you in advance!!!
If it is tempered glass, it cannot be cut
That's amazing, I just scored a 1/4" piece of glass that won't break, I tried tapping it with the ball on the end of the cutter, I guess I need something heavier to tap it with?
What is the glue (gum) are you use ,reply me
Its not glue it is kerosene oil, as I mentioned
@@jugaadtechnology449 thanks ,koheda tiyenne
thanks alot...
many technic learned from this glass cuttng shows
Thanks for the tip
This is also a method of cutting thick glasses ....nothing wrong in it . All methods are almost same only diffrence is how you apply force after scratching the glass .👍👌
glass per miti lagaker cut kite hai yards kuchen aur?
Fine sir
May I ask you: If the glass was thinner ( about 2; 3; 4 mm...) , before it broke , we need to knock its face under the glass like you or do we bend it straight down? Thanks for your sharing on how to cut thick glass very good.
Knock the glass only if you absolutely have to... His technique is not that great... Knocking the glass can make the edge very uneven... Your welcome..
Nice
Thankyou sir
How can I buy a cutting blaide, and average price.
Semmaaa
pueden ponerlo en el piso y colocar un clavo en la linea de corte y hacer presión en ambos lados con los pies.. y zuazzzzz
All that tapping just for a wavy edge result.
Where to order?
That must have been the first time you have ever cut a piece of glass because you did almost everything wrong. I'm afraid I will have to sack your teacher.
19 mm ka glass kaatne mein itna time nahin lagta hai
Nossa que demora. Basta riscar_ colocar algo sobe a linha riscada e forçar para baixo my dear😅
How to cut a tampered glass???
Tempering is the final process for a glass .So it would not be possible to cut it.
Tempered glass is a different animal. Think of tempered as a bubble and you end up popping the bubble when you break the surface.
For me safety first use glove, I'm not use ruler straight to the point is using meter. and glass cuter Only,,, it's very fast,,
jab glass cutting kar na nhi ata to kyu kar raha hai
유리 참 힘들게 절단하네요 요즘 어떤 세상인데 아직도 유리에 오일발라서 절단을 하는곳이 지금도 있네요 주소알려주면 오일칼 선물로 보내주겠습니다 이 나라는 장갑이 비싸서 안쓰나요?
thanks for your appreciation.
Aap ye bhi likhe ki sirf glass wale expert hi ka te warna hath me lag sakta he bhai
keran bos ku 🙏🙏 salam kenal bos
Berapa kilogram tekananya?
Kis ne bola sheshe katna?
Jtna time aap ne lgaya mein ne 100 sheshe katy hoty
*_Keren Sekali_*
Gracias
عمليه معقدة قديمه . فيه ادوات اكثر فاعليه واقل تعب
Come here in tubod glass... We will show you how to cut 12mm thickness of glass.. That is so basic...
Kab sikha kam aur kahan se bilkul ajnabi Ho Bosss
19 mm katne me kitna time lagege
Etni Der m to kitne glass cut kerdiye hote am experts in glass work
ruclips.net/video/D0epZC3rxfk/видео.html see my video of glass cutting video
Are you using a normal kerosene??
Any other fluids are use?
Yes
I use mineral turpentine for cutting oil for years it works fine as well and cheaper than kerosene have been recycling glass for years much cheaper when doing your own repairs.
jitni der me ek kach cut kra utni der me me 10 kach cut krchuka hota smjane ke sath
itu minyak nya apa bang
certo che se in una officina per tagliare 60 centimetri di vetro ci mettessero 15 minuti ... sarebbe tutto piu ... molto caro ahahahahahah
No tiene ni idea como se corta un vidrio ese es un aprendis