I have 2 v10(vs990) both have a boot problem and I got my hot air rework station out set the temp at 300c and set the air flow at 1 and timed it at 1 min. I don't think it was to long of a time it took 3 tries . both phones are fully working now I just thought I would share the temp and air settings Thank you
@@inboxthebox6o467 Probably not. All reflow solutions for LG G4/V10 are only temporary fix. Why? Consider that factory brand new LG G4/V10 sometimes went into bootloop within months due to crap unleaded solder/underfill used by LG. So reflowing will certainly go back to bootloop even sooner. As shown in this video, permaanent fix involves removing ram chip, cleaning off the defective unleaded solder/underfill, reballing with good leaded solder and resoldering
Usually I'd be all over the lack of audio in this video, but he documented his work very well. Decent camera detail. I can at least get the gist of what's going on. But believe me when I say, ppl would appreciate audible directions and testimony in videos
Lots of the guys at XDA forums having success removing the logic board, placing in the oven at 385 for 8 minutes. My v10 was bricked for a year, tried all kind of ways to fix. Oven fixed it and typing comment on the v10 now. No issues since, we'll see how it lasts
Baking in oven is only short term solution. Your V10/G4 will die again. But it works great on LG G3!!! Guess why? Because LG started using crap solder on V10/G4. Only real fix is reball ram or both ram and cpu with good leaded solder.
Sabırlı olun arkadaşlar, 300 derece ısıyla çalışın, sabredin, acele ederseniz çipin ayaklarını koparırsınız yada çipi şişirirsiniz, ısıyı aynı yere tutmayın, sökülesiye kadar gezdirin, bulunduğunuz ortamın ısısıda çok farkeder unutmayın, bordu sağlam bi şekilde sabitleyip çalışın, çipi kaldırmak için zorlamayın, kendiliğinden kalksın, kenardaki silikonları cımbızla değil kürdanla temizleyin önce, hayırlı işler bol şanslar.
Camera perspective is not ideal when your arm blocks what you’re doing, otherwise helpful video. I’m assuming this is a permanent fix, yes? I think you’re doing what the internet says can’t be done. Good job.
Skynix marka ram kullanılan neredeyse bütün LG cihazlarda aynı sorun söz konusu. Gerçi, Skynix'in kendisi bir sorun. Isı geç düzelir mantığıyla geçiştirilmemesi gereken, ne kadar zaman harcansada muhakkak tecrübe edilmesi şart olan ''LG ram reballing'' işlemi. Ellerine sağlık ustam! saygılar...
my V10 was completely dead, I watch your video several times, open up my V10, did a heat gun fix procedure, and the V10 now start up but still doing the boot loop. What else can I do to repair it? is the connection still not good?
Wow apparently LG phones are best to stay away from currently own a Nexus 5x made by LG and it suffers from a similar problem was planning to buy this LG V10 I think it's best to stay clear of any LG products... A lot of videos talking about this bootloop problem just like the Nexus 5x
elina saglik filim gibi izledik ustacim bendede g4 var bootlop oldu bu islemi kaca yapiyorsun birde piyasada 150 tlye yaparim diyenler var onlar bu islemi bu sekildemi yapiyor yoksa sadece ustten isitip gecicimi yapiyorlar sorunlar tekrar nuksediyormus bu yontem kesin cozummu birde adres telefon vs alirsak iyi olur ben istanbuldayim
İşlem Gerçekten Çok Temiz Fakat Daha Sonradan Yeniden Isınma Olacağı İçin Bu Sorunu Nasıl Çözüyorsunuz .Bir makalede Çekirdeklerin Devre Dışı Bırakılması Çözüm Olarak Yazılmış Bu Konuda Bilginiz Var mı Birde Ne Kadar Sağlıklı Oluyor Bilgi Verirseniz Çok Sevinirim.
Hello I would like to know what is called the material with which you make the mold that is in minute 30 to fill the holes of tin in cream in the processor?
LG G3 was fine for most part. Few bootlooped LG G3 is easy to fix. Real problem started with LG G4 where they chaged solder/underfill and bootloop became epidemic. Reheating bootlooped LG G4 is purely temporary fix because defective solder/underfill LG used.
Ufuk Bey. Aynı sorunu bende yaşıyorum tavsiye üzerine gittiğim bir usta 250 tl ye sadece ram değiştirebileceğini söyledi. Onun dışında herkes ya 800/900 tl civarı anakart değişimi yapabileceklerini yada 80 tl ye fırınlama yapabileceklerini söyledi. Ram değişimi tek başına yeterli olur mu. Anakartı değiştirmeden kalıcı çözüm olur mu. Teşekkürler
arkadaşlar bootloop oldu sandığınız telefonların lg logosunda kalıp açılmamasının bir nedenide bataryası olabilir sağlam sandığınız batarya belkide bozuk olduğu için telefon logoda kalıyor olabilir yani bozuk bataryada telefonun logoda kalmasına neden olabilir bu yüzden ilk önce sağlam olan bir batarya ile açmaya çalışın umarım sorun düzelir
Merhaba , v10 cihazımda güç tuşuna basıp açmaya çalıştığım zaman yeşil ekran alıyorum . telefonun garantisi devam ediyor . garantiden geldikten sonra sanırım sizin değiştiğiniz parça yada yaptığınız işlem yapılacak. Sorum şu , içinde ki bilgiler gider mi ? yada bu şekilde iken pc ye nasıl yedekleyebilirim ?
For those who talk shit about LG, let's not forget about nearly all of Samsung's Note 4s having memory controller failures after 2 years, note 6s exploding, and their failure to design a durable charging port since the s2.
This is not a thermal pad problem, but a mainboard issue. Did all this work the first day I got the phone and it lasted 5 months. First the fingerprint scanner was malfunctioning, then the CPU stopped working. Since then, there is no escape from bootloop. Got it back to life for a minute after heating up the CPU with a hairdryer and pressing the chip hard. Although the phone offers great features and software, I will never ever buy this model again. It's a ticking time bomb.
Milan Hoppe hi I hope you understand what I'm saying my phone have the same thing so how can I fixed i dont have the utensils can I just open the phone and use my hairdryer like u say and pressed the chip???
diana ruiz Send it in if you have warranty. If you bought an overseas model, you may just wanna follow the tutorial and my instructions. Then restart the phone and pray it will last for a backup. If it doesn't restart, try the same thing over and over again.
1) hot air rework station (maybe get a cheap one like 858D) 2) soldering iron with knife blade tip 3) bga blade for removal of the ramchip 4) flux for soldering 5) Note 3/samsung stencil for reballing 6) reballing paste. 7) some good old leaded solder. That's it!
bende lg v10 h901 yur dısı telefon var tlefona yazılım atmayı denim yazılımı attı telefon kapandı bi daha acılma qfil ile actım bi daha yazılım attıgımda aynı hata veriyor bunun bi cözümü varmıdır telefon öyle kaldı
Hii there sir would you plz give me the name of every tool you used to fix this phone i'm from 🇹🇳 and no one in my country knows how to fix this issue so i got to try to do it my self thnx 😊
My v10 get boot loop problem first then i try to heat up the chipset but now its dead and wanna know following ur step will make my mobile work again or not??? Thanks
that was the glue pasted from LG company to hold better. because when mobile get too hot then there is a chance that this Processor get displaced after falling down or from any serious shock. this guy did great job. i also did this but out of 5 only 3 survived.
It's called epoxy underfill. Unfortunately underfill used by LG was defective and caused bootlooping issue. Sure in custom repair underfill will be removed and it will be for the better as there is no longer underfill to cause bootloop issues.
Excellent repair video. What kind of flux did you use to help with the reballing and is replacing the underfill required for durability?
I have 2 v10(vs990) both have a boot problem and I got my hot air rework station out set the temp at 300c and set the air flow at 1 and timed it at 1 min. I don't think it was to long of a time it took 3 tries . both phones are fully working now
I just thought I would share the temp and air settings
Thank you
did they still working ?
@@inboxthebox6o467 Probably not. All reflow solutions for LG G4/V10 are only temporary fix. Why? Consider that factory brand new LG G4/V10 sometimes went into bootloop within months due to crap unleaded solder/underfill used by LG. So reflowing will certainly go back to bootloop even sooner. As shown in this video, permaanent fix involves removing ram chip, cleaning off the defective unleaded solder/underfill, reballing with good leaded solder and resoldering
@@springer-qb4dvwell i hope they also sells reworked v10 boards coz i still like this phone
I used these steps I thought it failed then the next morning my daughters v10 came back and working great.thanks
nickm73 :)
Muy buen video, lastima que en Argentina no saben reparar de esta manera. Lo primero que te dicen es que no tiene arreglo
Usually I'd be all over the lack of audio in this video, but he documented his work very well. Decent camera detail. I can at least get the gist of what's going on. But believe me when I say, ppl would appreciate audible directions and testimony in videos
Lots of the guys at XDA forums having success removing the logic board, placing in the oven at 385 for 8 minutes. My v10 was bricked for a year, tried all kind of ways to fix. Oven fixed it and typing comment on the v10 now. No issues since, we'll see how it lasts
hey can you give me the tutroial thanks :D
Hi ,
Have you the same problem stick on logo?
And how you fix it?
Behnam royal either u follow he video above or buy a new board
Baking in oven is only short term solution. Your V10/G4 will die again. But it works great on LG G3!!! Guess why? Because LG started using crap solder on V10/G4. Only real fix is reball ram or both ram and cpu with good leaded solder.
Güzel çalışma.wifi çipi değişimi de var mı
ufuk akgul que materiales utiliso y acuantos grados coloco la pistola de calor gracias espero una pronta repuesta saludes desde colombia
il faut etre un professionel pour faire ce que vous faite bravo
Одним Словом НАСТОЯЩИЙ ПРОФИИ!!! ВСЕ КРУТО СДЕЛАЛ! ТАК ПЕРЕКАТАТЬ ПРОЦ!
Sabırlı olun arkadaşlar, 300 derece ısıyla çalışın, sabredin, acele ederseniz çipin ayaklarını koparırsınız yada çipi şişirirsiniz, ısıyı aynı yere tutmayın, sökülesiye kadar gezdirin, bulunduğunuz ortamın ısısıda çok farkeder unutmayın, bordu sağlam bi şekilde sabitleyip çalışın, çipi kaldırmak için zorlamayın, kendiliğinden kalksın, kenardaki silikonları cımbızla değil kürdanla temizleyin önce, hayırlı işler bol şanslar.
Camera perspective is not ideal when your arm blocks what you’re doing, otherwise helpful video.
I’m assuming this is a permanent fix, yes? I think you’re doing what the internet says can’t be done. Good job.
Skynix marka ram kullanılan neredeyse bütün LG cihazlarda aynı sorun söz konusu. Gerçi, Skynix'in kendisi bir sorun. Isı geç düzelir mantığıyla geçiştirilmemesi gereken, ne kadar zaman harcansada muhakkak tecrübe edilmesi şart olan ''LG ram reballing'' işlemi. Ellerine sağlık ustam! saygılar...
Assalamualaikum
Makasih ilmunya...!!
Mau nanya apasih cairan yang di suntikan?
trus yang seperti tali di solder itu apa sih...?
nice work. what temp u used for the heat process?
Who have this problem on 2018?
my v10 is bootlooping 3 months ago till now , im thinking of buying stuffs for repair & try this video soon
mine
Mike Concepcion well i brought s6. I miss my v10 :'k
my v10 4 day ago, the repairer phone try to repair but after 1 hour, when installing app, it became hot and started to bootloop again
I have had it since 2017 I dropped off a dresser from 4 feet into carpet and it then boot looped but I want to see if I can fix it
ufuk usta o demirle kapattığın cipleri neden kapatıyorsun kapatmazsak ne olur bilgiverir misn?
my V10 was completely dead, I watch your video several times, open up my V10, did a heat gun fix procedure, and the V10 now start up but still doing the boot loop. What else can I do to repair it? is the connection still not good?
Wow apparently LG phones are best to stay away from currently own a Nexus 5x made by LG and it suffers from a similar problem was planning to buy this LG V10 I think it's best to stay clear of any LG products... A lot of videos talking about this bootloop problem just like the Nexus 5x
Great surgeon! !!! Beautyful Reballing. Congratulation
Ufuk abi sadece ram kalıplayıp takıyorsun bunlar geri gelmiyor mu sorun işlemci değilmi ?
Good day. Your video really liked your LG V10 repair. I am from Russia, could you undertake to repair my phone and how much will your work cost?
in which case is it enough to solder the RAM, and when it is also necessary to pull out the processor?
perfect work of reballing, congrats.
its permanent?
Where can I get the stencil?
uncertain
Hi, thank you very much for your Video!
What kind of 'paste' do you apply for reballing the IC-Chip?
standart AMTECH RMA-223
Sorry, i mean the 'paste' at 30:38 for reballing, not the Flux. Thank you!
Krem Lehim XG-50 42g Sn63/Pb37
Hi, one more Question: do you have the Article-Number of the metal plate (stencil) from Aliexpress that you use for reballing? Many Thanks again!
note 3 stencil
elina saglik filim gibi izledik ustacim bendede g4 var bootlop oldu bu islemi kaca yapiyorsun birde piyasada 150 tlye yaparim diyenler var onlar bu islemi bu sekildemi yapiyor yoksa sadece ustten isitip gecicimi yapiyorlar sorunlar tekrar nuksediyormus bu yontem kesin cozummu birde adres telefon vs alirsak iyi olur ben istanbuldayim
excelente amigo me sirvió. lo di por perdido el cliente quedo contento
Bro y el cliente ya no se volvió a quejar de que le volvió a fallar jajaja?
Abim eline saglik isinin uzmanisin belli ama senin dukkan nerde bi cevap atar yardimci olursan cok sevinirim.
настоящий мастер.я бы доверил свою технику.good!!!!
thanks
Cool
Ağlaya ağlaya vazgeçirdiler beni şu telefondan... sevgilisinden severek zorla ayrılmış gibi zırlıyorum, aahh lg g4 üm ühü ühü
İşlem Gerçekten Çok Temiz Fakat Daha Sonradan Yeniden Isınma Olacağı İçin Bu Sorunu Nasıl Çözüyorsunuz .Bir makalede Çekirdeklerin Devre Dışı Bırakılması Çözüm Olarak Yazılmış Bu Konuda Bilginiz Var mı Birde Ne Kadar Sağlıklı Oluyor Bilgi Verirseniz Çok Sevinirim.
Hello I would like to know what is called the material with which you make the mold that is in minute 30 to fill the holes of tin in cream in the processor?
Ariel Moreno stencil
ufuk bey herhangi bi cihazi actigmizda mesela islem ci hangisi emmc hangisi oldugnu anlamamizin bi yolu varmi ustamiz
Every lg phones has this problem
LG G3 was fine for most part. Few bootlooped LG G3 is easy to fix. Real problem started with LG G4 where they chaged solder/underfill and bootloop became epidemic. Reheating bootlooped LG G4 is purely temporary fix because defective solder/underfill LG used.
Ustam şok şok şok oldum ellerıne saglık..ustam karsı tarafa ses gıtmıyor v10 alt mıkrofon .nasıl yol cekebilirim.yerini bulamadım...
Ufuk Bey. Aynı sorunu bende yaşıyorum tavsiye üzerine gittiğim bir usta 250 tl ye sadece ram değiştirebileceğini söyledi. Onun dışında herkes ya 800/900 tl civarı anakart değişimi yapabileceklerini yada 80 tl ye fırınlama yapabileceklerini söyledi. Ram değişimi tek başına yeterli olur mu. Anakartı değiştirmeden kalıcı çözüm olur mu. Teşekkürler
Ufuk bey bu sorunun tamir fiyatı nedir bendede var aynı sorun.
Y cuanto por la misma operacion del mismo modelo
Hocam maşaallah iyi iş çıkardın. Allah ilmini arttırsın.
Hey what are these 2 metall plates you put on the platine for ...protection or stabilisation? Where do i get them?
Esta es una solucion permanente!????? Para el v10?
Friend I have another question, what is the name of the flux you use for tin?
Ustam kaç derece ısıda hava nasıl olucak ustam ben denedim ram sisiyor
aynı sorun benim cihazımdada var malesef tamir ettirmek istiyorum ücreti nedir
in the 34:46 you have the ship with the part number print again, but you remove it in the minute 20:50, so is a different chip you just buy it?
Im not confident to do this for my LG V10, is anyone knows where I can get someone like this guy to fix my phone in London, Lille or Brussels?
My set show no logo nothing only black screen i am using this fone from 6months is this method is applicable with my fone???
Very nice work Ufuk!
Hello
There is a way to test the IC?
How much temperature and how much wind time the device will damage the IC?
arkadaşlar bootloop oldu sandığınız telefonların lg logosunda kalıp açılmamasının bir nedenide bataryası olabilir sağlam sandığınız batarya belkide bozuk olduğu için telefon logoda kalıyor olabilir yani bozuk bataryada telefonun logoda kalmasına neden olabilir bu yüzden ilk önce sağlam olan bir batarya ile açmaya çalışın umarım sorun düzelir
Tebrikler hocam eline sağlık. Memleket nere ?
Adamın işi gücü yok şimdi sana memleket yazar töbe töbee, işiniz gücünüz muhabbet gırgır şamata arkadaş, usta orda çip söküyo şimdi heeeyy.
O an aklıma o gelmiştir ya da bi maksatla sormuşumdur. Ne var bunda. Sürekli çip sökmüyor ya
I have a v10 with the same problem. Do you wanna buy it from me?
Where can I get the stencil solder tin template?
Hello, Thank you for the movie. Please take a moment to complete.
And here's where to find out if the problem is with Rome or CPU؟
ufuk bey bu soktugunuz cip in adine işlemcimi bu ayrintil soylerseniz ustacim
ram söktügüm chip
Merhaba , v10 cihazımda güç tuşuna basıp açmaya çalıştığım zaman yeşil ekran alıyorum . telefonun garantisi devam ediyor . garantiden geldikten sonra sanırım sizin değiştiğiniz parça yada yaptığınız işlem yapılacak. Sorum şu , içinde ki bilgiler gider mi ? yada bu şekilde iken pc ye nasıl yedekleyebilirim ?
please can you lg stylo 2 keep restarting I don't know how to fix it
I have the same problem how can I fix it for good ?
30:20 deki kalıbı nereden temin edebiliriz ? (where can we buy that stencil ?)
My friend, what's the name of that thin piece you use to take off memory?
DIYFIX 14 ADET IC Chip Onarım Ince Bıçak Aracı CPU Remove ,,,,,,,,,,,,,google copy paste
Thank you very much my friend, you are a true professional.
Thanks
What materials do you use? please
nekadara degişiyosunuz
Hi Where you are from?
في الدقيقه 31:12 ما اسم الصفيحه المستخدمه انا قمت بكل الخطوات عدا هذه الخطوه ارجو الرد باسرع وقت
thanks for showing the world how useless LG products has become.
how does the frame come out of motherboard and how does it go back in again
Good job
Don de te puedo ubicar tengo un lg v10 igual amigo
you are a master
Ufuk bey bir fiyat verseniz (açıklamadaki yerlere gittim fakat bu sorunu bulamadım haliyle fiyat da alamadım )
How much temperature did you apply and how much time plz
320
Ufuk Akgül thanks
Ufuk Akgül 320 Celsius or Farenheit?
Celsius
How about air??
Hey where can I get this stencil for V10 IC ??? I searched for it on AliExpress buts not available.. only Samsung and iPhone stencils are available...
Fahim Shaikh note 3 stencil
Ufuk Akgül thank you my friend... :)
By the way... How long did it last after rework/reballing did you put any heat sink stuff to disperse heat???
entegre kalıbını nereden aldınız ben uygun bı kalıp bulamadım da ?
note3 kalıbı kullanıyorum
teşekkür ederim cevap için muazzam çalışıyorsun allah emeğini zayi etmesin..
Amin kardeşim
ısı istasyonu derecelerini paylaşma imkanınız var mı ? sanırım ben ısıyı yüksek verdiğim için flux hemen yanıp gidiyorda.
For those who talk shit about LG, let's not forget about nearly all of Samsung's Note 4s having memory controller failures after 2 years, note 6s exploding, and their failure to design a durable charging port since the s2.
Very great job!!
Plz tell me you import the LG v10, s motherboard in Pakistan city karachi
Im gonna trying and see whats coming!
vi kamon asan ? vi amar LG V10 phone a power ic problem ! ami ki apnar phone number patapari ?
This is not a thermal pad problem, but a mainboard issue. Did all this work the first day I got the phone and it lasted 5 months. First the fingerprint scanner was malfunctioning, then the CPU stopped working. Since then, there is no escape from bootloop. Got it back to life for a minute after heating up the CPU with a hairdryer and pressing the chip hard. Although the phone offers great features and software, I will never ever buy this model again. It's a ticking time bomb.
Milan Hoppe hi I hope you understand what I'm saying my phone have the same thing so how can I fixed i dont have the utensils can I just open the phone and use my hairdryer like u say and pressed the chip???
diana ruiz Send it in if you have warranty. If you bought an overseas model, you may just wanna follow the tutorial and my instructions. Then restart the phone and pray it will last for a backup. If it doesn't restart, try the same thing over and over again.
Milan Hoppe thanks 🙌🏻
Who could tell me what tools and materials he uses? Thank you very much in advance.
Is very simpl
1) hot air rework station (maybe get a cheap one like 858D)
2) soldering iron with knife blade tip
3) bga blade for removal of the ramchip
4) flux for soldering
5) Note 3/samsung stencil for reballing
6) reballing paste.
7) some good old leaded solder.
That's it!
Great Work!
great work long live turkey
Temp ?
Air FLow ?
320
2,5
Temp 4 aire 4 5
bende lg v10 h901 yur dısı telefon var tlefona yazılım atmayı denim yazılımı attı telefon kapandı bi daha acılma qfil ile actım bi daha yazılım attıgımda aynı hata veriyor bunun bi cözümü varmıdır telefon öyle kaldı
hello my friend, I have a problem. I did all to you video, but now my lg V10 I don't turn on. Please tell me a solution. Thank you
Hii there sir would you plz give me the name of every tool you used to fix this phone i'm from 🇹🇳 and no one in my country knows how to fix this issue so i got to try to do it my self thnx 😊
Bro if wo change the board ?
you are the best.
Thanks
Ucret ne kadar
انتا فنان
My v10 get boot loop problem first then i try to heat up the chipset but now its dead and wanna know following ur step will make my mobile work again or not???
Thanks
try your luck. You will do it at 320 degrees
Ufuk Akgül only heat up or all process
Just heat up bro
I am not professional so i try yo heat up and applied thermal paste and pads
One of my near shopper has hot air gun so i use his gun
Hi my friend what is the cleaning material at 28:55. Thanks
alcohol
Good luck
so basically you gotta remove the processor and clean it
Y si no le metes flux no va a salir rapido
What was scraped off from under the memory?
that was the glue pasted from LG company to hold better. because when mobile get too hot then there is a chance that this Processor get displaced after falling down or from any serious shock. this guy did great job. i also did this but out of 5 only 3 survived.
It's called epoxy underfill. Unfortunately underfill used by LG was defective and caused bootlooping issue. Sure in custom repair underfill will be removed and it will be for the better as there is no longer underfill to cause bootloop issues.
@@springer-qb4dv thanks for the reply. 😊
@@mostwantedtraders4238 tbanks for the reply three years ago! 😊
Abi tempratur nasil veriyorsun ki cpu altinds problem cikmiyor?
320 derece
Allah razi olsun Abi.
Punya saya matot bos. Bagaimana solusinya
Bravo