Thank you for such great detail! I now understand what I have been doing wrong! I stir too fast and not enough layers. BTW I would like your opinion about my technique for removing bubbles as I don't have a pressure pot. I mix the resin in a cup that is sitting in warm/hot water, it makes the stirring so much easier and then after 4 min I just let it sit for a min and all the bubbles are gone. I believe it shortens the work time because of the heat, so it has a slight downside. What are your thoughts please?
I am a great fan of your work and tried to make the tea light candle deep casting ,. I had some idea that it has to be done in layers so I poured in 3 layers and ended up With full of bubbles! Today when i saw your video on you tube I realised so much patient is required to make that!! Thankyou for sharing the tutorial as I had given up on deep casting… but will try now for sure!!
So useful video,i understood my fault while pouring resin very thick layer and it became very hot 😢and damaged my product... what is the size of mold how much resin poured totly
Thts indeed so mch of patience....the most awaited video..tks mch fr the share ..wud love to.knw hw the presure pot luks and hw it wrks....tks mch again..gdday!
I have a doubt did u use 2:1 resin ....usually for deep casting usually 3:1 resin right ? I don't have much knowledge correct me if am wrong ...thank you 😊
Beautiful work. How many days did you take to make this project? So you want 3 to hours between each layer. What happened if it was done in less layers
From where do u get the dried flowers ? Because I dry them at home but the colour doesn’t come so bright … can u share a link as to from where to buy these dried flowers
Thank you for this wonderful tutorial.. so helpful .. What size of pressure pot do you use? Would love to have a short tutorial on how to use it. Thank you so much for sharing this tutorial 😊😊
Thank you for such great detail! I now understand what I have been doing wrong! I stir too fast and not enough layers. BTW I would like your opinion about my technique for removing bubbles as I don't have a pressure pot. I mix the resin in a cup that is sitting in warm/hot water, it makes the stirring so much easier and then after 4 min I just let it sit for a min and all the bubbles are gone. I believe it shortens the work time because of the heat, so it has a slight downside. What are your thoughts please?
The red one is absolutely gorgeous! 🥰 thank you for such a great tutorial! ❤️
Thank you for sharing the detailed tutorial. If possible could you please show us the pressure pot.
Thank you so much for such a detailed tutorial.....very helpful.....and these looks so beautiful 👌🏻👌🏻👌🏻
How you pop bubble in the mould without pressure pot?
I am a great fan of your work and tried to make the tea light candle deep casting ,. I had some idea that it has to be done in layers so I poured in 3 layers and ended up
With full of bubbles! Today when i saw your video on you tube I realised so much patient is required to make that!! Thankyou for sharing the tutorial as I had given up on deep casting… but will try now for sure!!
Thank u so much for sharing such a beautiful DIY. Can u also please make a video on how to use the pressure pot?
Hi, you’ve done in 3 days so when you sleep at night it will be more than 4 hours… so does it affect the casting??
So useful video,i understood my fault while pouring resin very thick layer and it became very hot 😢and damaged my product... what is the size of mold how much resin poured totly
Thts indeed so mch of patience....the most awaited video..tks mch fr the share
..wud love to.knw hw the presure pot luks and hw it wrks....tks mch again..gdday!
will the resin from the cup will become hard as well??
these are lovely but does the resin get hot with tealights or should you use the fake ones
Thank You So much Divya for such Beautiful n detailed Tutorial made with so much of Love n Patience 🥰🥰
Can we do single pour in the mould ?
I have a doubt did u use 2:1 resin ....usually for deep casting usually 3:1 resin right ? I don't have much knowledge correct me if am wrong ...thank you 😊
Beautiful work. How many days did you take to make this project? So you want 3 to hours between each layer. What happened if it was done in less layers
Thanks for this tutorial…. Plz send the material link also…
Thanks for each and every detail to be followed
Lovely video! If I use a deep cast resin that takes 72 hours to cure, should I wait for longer to pour the next layer?
@@colorstorybydivya thank you!!
what type of resin do you use?
What kind of gloves are you using they look very comfy.. I can't use the medical ones they cause allergies
May I kno .. what is ur opinion on using 3:1 resin as it can be poured in larger quantities
Y we need a interval ....y can't we put all at same time..i m learning about it....wanna know that's y
From where do u get the dried flowers ? Because I dry them at home but the colour doesn’t come so bright … can u share a link as to from where to buy these dried flowers
Kindly check The forever ferns on Instagram
What is the reason to do layer by layer and not all at once??
Sand paper or any tool will affect on shine of resin .. it gives scratches to the art … then how to cure that scratch ?
Hi ! What about the tiny holes which have appeared on your tea light holder bottom, can you please tell me how to fix them? Thanks
Thank you for the tutorial, very well explained, in my work micro bubbles are there
can you make short video on how to use pressure pot??
Hola, las flores las secas en sémola ?
Thanku for the tutorials 💓 beautiful explain
Thank you for this wonderful tutorial.. so helpful .. What size of pressure pot do you use? Would love to have a short tutorial on how to use it.
Thank you so much for sharing this tutorial 😊😊
Hey is the video for pot already out? Been waiting for it!!
Btw, these are beautiful ❤❤
What is the glouse name or type used
Thank you for the detailed tutorial ❤️❤️
May I know the reason for why layers are not visible ?
@@colorstorybydivya ok ok.. got it
one more thing.. 3-4 hrs means how will be the resin? will that be
hard or sticky?
It’s really beautiful thank you for the tutorial
Thank you. This is so beautiful. Can you share where you get your flowers or do you dry them?
I am not seeing the information. If they are from your site I would love to order but I don’t see them on your site either
I can’t get it out of the mold bad sticky
check your resin mix
What can we do with few small sized gaps that would have been a bubbly but now left an empty space
@@colorstorybydivya Thank you Divya ❤
Hi. Wat is pressure pot
Cc le rose est magnifiques
Beautiful
Pressure pot link?
Not available
Beautiful✨
Beautiful!!!!
From Jim’s wife Tara that’s gorgeous I did mine all wrong a very sticky ugh Jesus is awesome yours is beautiful thanks
Thank you! Cheers!
So beautiful ❤️❤️
I didn’t do step by step
hope this helped
Love ❤️ 😍
Lastima que no traducen la explicación
Podrías por favor poner con subtítulos muchas Gracias 🙏🏻
✨🙏✨
ارجو ترجمة الفيديوات الى اللغة العربية.. وفقك ربي
👍👍👍👍👍
Beautiful