Awesome cabinets. I have a suggestion though to help manufacture better bass. I see you are using egg crate foam to dampen the cabinets. That’s a no no. Foam kills bass. Get some fiberglass insulation (r11, r12, or r13) and staple it every 4” down to 1” thick and cover all sides accept the baffle. You will hear a drastic improvement in your bass.
The frequency response is not satisfactory. The high frequency of the driver unit is exceptionally strong compared to the low frequency, so I should put it in the TQWT box that is efficient for low sound amplification.
I had a similar problem with Monacor SPX-200WP speakers. I used a parallel notch circuit from 1kHz to 6.5kHz, with 6dB attenuation. TQWT not a better solution, but one of the options.
@@philwoodcraft I had the same problem with the (somewhat) new SB 8" whizzer cone full range. I used a TQWT and an active crossover, -3db of baffle step correction and -2db high shelf from 3.8khz and above. With 10 degree off listening position, the sound is much improved.
hi I have pair of mark audio 10P full range but this sounds a lot better than mine the high-frequency is better, could you play some vocals like Diana krall, but i read that the bigger ones sound better
That's right. This unit I used has a high-pitched decibel. On the other hand, the ability of the enclosure is important because of the lack of low-pitched volume.
hi what does the enclosure have to have you listened to the next model up from that it is meant to be better and what valve are you using it made all the differance
Hey, I have watched all your videos. Just built a 8in Fostex Transmission line set that sound awesome. If you could recommend just 1 out of all of your builds to recommend what would it be? Which pair really blew your mind when you were listening to them?
Hi there. Great video! I have watched some of your videos. You do amazing work. I have build a couple of speakers my self but no longer have those tools necessarily for the job. Do you do any custom work? Thanks.
Very good as always, great job! What technique do you use to find the right thickness of the support base for the speaker, "the hollow" since the thickness of the tip of the cutter is 6mm? Do you move the guide tip every 5-6mm until it reaches the size of the basket? obviously if you exceed the measurement this will be cut when you make the central hole to let the speaker in. Thank you. :)
What do you mean by wide tip? more than 6mm? by doing so then you find yourself with the measures? your template has the required points, if you don't take a 6mm tip you can't find the measurements, or am I wrong? By the way, how is your template attached to the milling machine? the 4 holes are not on the template, did you glue it? If so, what glue did you use? Or did you pierce the template and put some screws? Sorry for too many questions, but I'm learning :) Thanks.
Hi friend, what size do you use for screws? 3x30mm or what? is it a problem if the screw pierces the wood and comes out on the other side inside the wooden box? better to take them shorter? thank you!
Hi, every time I hear the sound of the full range again, I enjoy hearing how deep and balanced it is, just pleasant to the ear, just wow
Thank you very much for watching and enjoying the video
Is it possible to know the measurements of the speaker?
I think it would sound better to send ducts on either side or back like this rather than forward. This seems like a very good idea.
Beautiful work and great sound just wonderful,It's a pleasure to see your works and hear them
What a pleasant compliment.
Thank you.🙂
Awesome cabinets. I have a suggestion though to help manufacture better bass. I see you are using egg crate foam to dampen the cabinets. That’s a no no. Foam kills bass. Get some fiberglass insulation (r11, r12, or r13) and staple it every 4” down to 1” thick and cover all sides accept the baffle. You will hear a drastic improvement in your bass.
👍
잘 보았습니다 저도매력에 빠져 두조의 플랜지를 운영하고 있지요
풀레인지에 인클로저 매칭만 잘 맞추면 정말 훌륭하죠^^
Did you take any frequency response measurements? Cabinet tuning? You took a very interesting approach to the venting. Nice job overall, as usual.
The frequency response is not satisfactory. The high frequency of the driver unit is exceptionally strong compared to the low frequency, so I should put it in the TQWT box that is efficient for low sound amplification.
I had a similar problem with Monacor SPX-200WP speakers. I used a parallel notch circuit from 1kHz to 6.5kHz, with 6dB attenuation. TQWT not a better solution, but one of the options.
That's right. As you said, notch filter is a good way.👍
@@philwoodcraft I had the same problem with the (somewhat) new SB 8" whizzer cone full range. I used a TQWT and an active crossover, -3db of baffle step correction and -2db high shelf from 3.8khz and above. With 10 degree off listening position, the sound is much improved.
과정, 구조 다 보여 주시네.😊
Excellent video! What products did you use in painting? Thanks in advance.
Cool speaker and amp 👍
Thanks🙂
편하게 bgm용으로 이유닛 보고 있었는데 소리가 생각보다 단단하고 강성이네요. ㅎ
데이톤오디오 제품들의 특징인거 같습니다.
새로운 영상 잘보았습니다.덕트 좌우 대칭이 아닌게 독특하네요. 스테인으로도 짙은색상이 나오는군요
덕트는 각각 좌우 양방향으로 나오는 대칭입니다^^
스테인은 얇에 덧바르면 색이 진하게 나옵니다.
시청해 주셔서 감사합니다!!
@@philwoodcraft 영상 올라오자마자 리플달은거라 자세히 못봤네요. 독특한 구조 소리 듣고싶네요.
저음이 워낙 약한 유닛이라 한계가 있습니다😪
hi I have pair of mark audio 10P full range but this sounds a lot better than mine the high-frequency is better, could you play some vocals like Diana krall, but i read that the bigger ones sound better
That's right. This unit I used has a high-pitched decibel. On the other hand, the ability of the enclosure is important because of the lack of low-pitched volume.
hi what does the enclosure have to have you listened to the next model up from that it is meant to be better and what valve are you using it made all the differance
👍👏👍👏👍👏
😄
Hey, I have watched all your videos. Just built a 8in Fostex Transmission line set that sound awesome. If you could recommend just 1 out of all of your builds to recommend what would it be? Which pair really blew your mind when you were listening to them?
Thanks for watching. I think.. Fe108 sol is the best.
Hey thanks so much. I really enjoy your videos. Thanks for sharing.@@philwoodcraft
Hi there. Great video! I have watched some of your videos. You do amazing work. I have build a couple of speakers my self but no longer have those tools necessarily for the job. Do you do any custom work? Thanks.
Working on custom speakers and interior speakers in cafes is my job. Check out my Instagram.
Very good as always, great job!
What technique do you use to find the right thickness of the support base for the speaker, "the hollow" since the thickness of the tip of the cutter is 6mm? Do you move the guide tip every 5-6mm until it reaches the size of the basket? obviously if you exceed the measurement this will be cut when you make the central hole to let the speaker in. Thank you. :)
It's right to work the way you say it. However, the first 5 mm deep is to be used with a wide trimmer bit.
What do you mean by wide tip? more than 6mm? by doing so then you find yourself with the measures? your template has the required points, if you don't take a 6mm tip you can't find the measurements, or am I wrong?
By the way, how is your template attached to the milling machine? the 4 holes are not on the template, did you glue it? If so, what glue did you use? Or did you pierce the template and put some screws? Sorry for too many questions, but I'm learning :) Thanks.
It's good to ask questions.
The size of the tip is large, the location of the hole can be deducted. And I used 401 bond for fixing.
@@philwoodcraft thanks a lot my friend :)
I look forward to the next job, nice day!
👍
좋네요. 녹음 구간을 좀 늘려줄 수 있나요? 클래식과 일반 가요(팝송) 같은 것을 같이 듣고 싶어요.
스마트폰 녹음이라 큰 의미가 있을지 모르겠네요.
기회가 되면 모아서 올려보겠습니다.
Hi friend, what size do you use for screws? 3x30mm or what? is it a problem if the screw pierces the wood and comes out on the other side inside the wooden box? better to take them shorter? thank you!
The length doesn't matter, but I use m4*20.
@@philwoodcraft
Thanks friend for always answering me, see you soon!
흡음재를 넣지 않으면 어떤차이가 있는지요? 알려주시면 감사하겠습니다
고음을 흡음하여 포트를 통해나오는 저음을 단정하게 합니다.
넣지않으면 소리가 산만하겠죠.
@@philwoodcraft 아 그렇군요 배웠습니다 감사합니다
마이크를 새로 장만해보실생각은 없으신가용?
비용 압박이 심해서 망설이고 있습니다.
가지고 계신 공구중에 검정색T자의 정확한 명칭을 알고싶네요. 저도 하나 구입해서 사용하고 싶어서요.^^
항상 감사하게 영상시청하고 잇습니다.
항상 시청해 주셔서 감사합니다🙂
T형 버니어 캘리퍼스입니다.
@@philwoodcraft 좋은 정보 감사합니다.
스피커를제작해서 판매도하나요?
네. 영상의 반정도는 주문품 촬영입니다.