Hello friends, when you do it, use a thick tube, clean it before applying the glue, after gluing, let it take about 3 hours for the glue to harden, dilute the paint, compress the gas 3-4kg is safe. After using, you open the top cover to put gasoline in the washer and open the pump needle of the car valve to let the gasoline out chào các bạn khi làm các bạn sử dụng ống loại dầy, vệ sinh sạch sẽ trước khi dán keo sau khi dán xong để khoảng 3h cho keo khô cứng lại, sơn pha loãng, nén khí tử 3-4kg là an toàn. sử dụng xong các bạn mở nắp bên trên cho xăng vào xúc rửa và mở kim bơm của van xe cho xăng ra ngoài
through the fuel hose of a gasoline trimmer +, a syringe. We pump the paint into an empty balloon Finishing propane gas lighters It will be like factory paint. The viscosity of the viscometer to pick up . Translated via Google translator.
Honestly, I was annoyed last I was looking for a video or guide to make something similar since everyone said you can't make it or it wouldn't be safe... better were the days when you simply had a book to show you how to recharge your non-rechargeable batteries and use those piles of asbestos shingles you have lying around... I guess not everything aged well in those books, but still people back then assumed people were smart enough to not deviate from a guide and potentially kill themselves... I plan on using your design as a base for a refillable air blower. Thank you a million for the great guide, I look forward to making it :D
Молодец, парень дай бог тебе здоровья и благополучия новых творческих успехов и хорошего настроения хорошо, что придумал многоразовый балончик бывает так, что нужной аэрозольной краски не найдёшь, за-то можно самому подобрать какой тебе надо цвет🤝👍💪🇷🇺🛠️!!!
@@Unutop ну ё маё, ну хоть чуть-чуть голову включи, всмысле фантазию…. Припаиваешь металическое горлышко с резьбой, сверху крышка, типа как от фляжки армейской, а в крышку ниппель. Естественно всё через уплотнительные резинки.
Very good idea. Only problem is every time we have to use the correct amount of paint for the job. Because we have to clean the valve if not it will get stuck.
Có 1 vấn đề là trong sơn pha sẽ có axetone, không biết cao su và nhựa có chịu được khi ngâm trong axeton không? Làm để chống cháy thì ok chứ dùng lâu dài thì không ổn.
This idea is very cool, but also very dangerous, if this plastic can't handle the pressure and it bursts, it goes straight in your face, or it can burst in your hand, be very careful with pressurized pressure, it's very dangerous
hello but you can use the compressor for see how strong is this thing and test it with a lot more pression to see at what point he break this is what people do for air bottles for undersea
На какую площадь хватает одной накачки воздухом? Баллоны с краской обычно наполняют специальным газом , а не воздухом потому что воздух в отличие от тех газов хуже сжимается . А раз хуже сжимается , то давление быстро спадет и нужно будет подкачивать баллон снова и снова.
Thanks for sharing, it is a cool idea for sure and I will to try it. Just a tip for you, I think that you will find that you will get better results when using your adjustable pliers in the correct direction. You always tighten against the fixed jaw. It makes them easier to hold closed and the teeth in the jaws were made in this way. Most people don't know or think about it, so I thought I would just put it out there since you were nice enough for sharing your idea.
Exelente una crítica constructiva uniera Sido mejor Aser el cuerpo con tubería roscable hasta para llenarla con mayor facilidad y por mejor seguridad saludo y éxitos en tus proyectos
🇬🇷 Πάρα πολύ ωραία η ιδέα και η κατασκευή, συγχαρητήρια. Για να δούμε όμως εάν βγάζει αέρα η συσκευή, νομίζω ότι θα ήταν καλύτερα να τη βυθίσουμε ολόκληρη μέσα στο νερό. Τώρα εάν υπάρχει κάποιος άλλος λόγος, εγώ δεν το γνωρίζω.
I tried more or less the same patent, " Paint Bomb !!!!". The thinners dissolve the PVC Glue and then the "spray can" blow apart where the peaces are glued together with a very "loud bang" and paint every where. Use the same method, but just use metal piping (galvanize) that screw together. A bit heavier, but much much more secure.
Bonjour 😊 Vu que je suis français 🤔 il y a des mots que je ne comprends pas 😢😥 mais sinon c'est une super invitation 👍👍 bravo 👏 bravo 👏 vous êtes un génie 😯 🤘🤘🤘
Con algunos usos más es posible que se deterioren las gomas que hacen de sellos y el pegamento que unen los tubos con las tapas por los solventes que utiliza par diluir la pintura
B. Días amigo. Es buena idea amigo. Sin embargo es muy peligroso, no es un recipiente a presión, por lo tanto no cumple cumple con normas y es un peligro al cargarle el aire. Saludos desde México y que Dios te bendiga.
You will not find leaks by putting bubbles over something that makes bubbles. Apply soapy water. NOT bubbles. How do you clean old paint out of your new spray can? Please learn to hold your pipe pliers correctly.
Excelente para quê? no mercado existem pulverizadores para serem ligados aos respectivos compressores. De facto, os pulverizadores são seguros, têm um jacto regulável e não tens de fazer este trabalho inútil de cortar canos e colar os canos que depois de duas ou três utilizações se desprendem devido ao facto dos solventes dissolverem a cola.
My thoughts were the same as yours. This is so stupid. 13 dollars for a cheap hvlp paint sprayer and he probably would have spent less money than making this trash.
As a next level modifications you could get a spray gun and hose from harbor freight so you could change nozzle size. Maybe go with a little larger pipe so you could clean out. careful with pressure. If using latex paint, water will clean out.
Or just buy the fucking paint spray gun intended for this job in the first place for 13 dollars, you know since your already at Harbor Freight. At first I thought that what you comment was going to say
Its reusable! only you need is to clean after use, just as we do in spray guns(cleaning nozzel is a key), its a quality time spent to make as well cheap
I don't see why it couldn't be done but it would add an extra point to leak from. Plus if it starts to leak once you have paint in there it will basically glue the threaded cap on.
Using soft copper or polly seals for pvc not rubber due to the chemicals like brake cleaner. It's best you use mild chemicals in a pvc container. In all and all great pvc spray container.
Hello friends, when you do it, use a thick tube, clean it before applying the glue, after gluing, let it take about 3 hours for the glue to harden, dilute the paint, compress the gas 3-4kg is safe. After using, you open the top cover to put gasoline in the washer and open the pump needle of the car valve to let the gasoline out
chào các bạn khi làm các bạn sử dụng ống loại dầy, vệ sinh sạch sẽ trước khi dán keo sau khi dán xong để khoảng 3h cho keo khô cứng lại, sơn pha loãng, nén khí tử 3-4kg là an toàn. sử dụng xong các bạn mở nắp bên trên cho xăng vào xúc rửa và mở kim bơm của van xe cho xăng ra ngoài
check it is fart proof👨🏭;
Qqqqqqqqq1qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
through the fuel hose of a gasoline trimmer +, a syringe.
We pump the paint into an empty balloon
Finishing propane gas lighters
It will be like factory paint.
The viscosity of the viscometer to pick up .
Translated via Google translator.
Rất hay hay hay hay hay hay hay ❤❤❤❤
Ccccxcccccxccxccxccc@@TANTRAN-jw1nx
Very creative video. I didn't expect paint sprayer to be made this way. Congratulations.
very clever jig. thanks for including the dimensions too.
Hay Quá Thầy Ơi! Em sẽ làm 1 cái để sơn xe Nhưng sẽ làm to hơn
ok bạn!!!
Làm to quá ko nhấc nổi đâu bạn, ko linh hoạt. Lại thêm phải bấm để sơn nữa chắc gãy tay. 😅
Hey, all I could say after watching this is;
"YOU'RE TOO GOOD MAN!"
......... Instead you are a genius.
Tuyệt vời anh ơi
thanks bạn!!! chúc kênh của bạn ngày càng phát triển
@@sonlai cảm ơn Anh
hơi nguy hiểm, đang bơm nó nổ cái bùm, sơn bay đầy người có khi mù mắt luôn 😂
Habría que saber a cuantos BAR/PSI llenar por que si puede terminar en desastre jaja
Honestly, I was annoyed last I was looking for a video or guide to make something similar since everyone said you can't make it or it wouldn't be safe... better were the days when you simply had a book to show you how to recharge your non-rechargeable batteries and use those piles of asbestos shingles you have lying around... I guess not everything aged well in those books, but still people back then assumed people were smart enough to not deviate from a guide and potentially kill themselves... I plan on using your design as a base for a refillable air blower. Thank you a million for the great guide, I look forward to making it :D
Молодец, парень дай бог тебе здоровья и благополучия новых творческих успехов и хорошего настроения хорошо, что придумал многоразовый балончик бывает так, что нужной аэрозольной краски не найдёшь, за-то можно самому подобрать какой тебе надо цвет🤝👍💪🇷🇺🛠️!!!
you are a genius , you are very clever , you are very good
Гениально, из баллончика сделал баллончик👍.
Из одноразового баллончика сделал многоразовый баллончик. Теперь понятно?
@@Unutop то есть в одноразовый баллончик нельзя что-ли клапан впаять???
@@Aisi-304 а краску как заливать?)))
@@Unutop ну ё маё, ну хоть чуть-чуть голову включи, всмысле фантазию….
Припаиваешь металическое горлышко с резьбой, сверху крышка, типа как от фляжки армейской, а в крышку ниппель. Естественно всё через уплотнительные резинки.
reir de algo formidable, triste personita.
Chào bạn bạn chia sẻ video tuyệt vời quá bạn ơi chúc bạn sức khỏe thành công hẹn gặp lại bạn 👍👍❤❤❤❤❤❤
đã từng lm với bình atm nhưng cho sơn vào hơi khó, bình này cải tiến cho sơn dễ hơn
ok bạn
đầu cho sơn vào vẫn nhỏ, cải tiến là gắn thêm cái zacor vào để cho sơn dễ hơn
Mua cái phiểu (loại nhỏ) bằng inox 304 thì rót sơn vào bình ok - Trên lazada có bán cái phiểu nhỏ này khoảng 50k/cái
Very good idea. Only problem is every time we have to use the correct amount of paint for the job. Because we have to clean the valve if not it will get stuck.
If you invert the can and blow air through it like the original cans.. should work.. but why was the paint lacking misting very large drops coming out
Wauw wauw mantap keren abiis ide kreatifnya sy suka 👍👍👍👍👍👍👍
Có 1 vấn đề là trong sơn pha sẽ có axetone, không biết cao su và nhựa có chịu được khi ngâm trong axeton không? Làm để chống cháy thì ok chứ dùng lâu dài thì không ổn.
Một ỷ tưởng rất hay và tuyệt Vời Ông Mặt Trời ☀️ luôn Bác Nhỉ. Cắm Ơn Bác đã chia sẻ...❤️❤️❤️👬👍👬❤️❤️❤️
thanks bạn!!!
Sáng tạo.hay wa đó Sơn
Dạ cháu cám ơn cô
So creative .
Thank you so much .
I am from SRI LANKA.
Amazing DIY. THUMBS UP
Rất hữu ích , cám ơn anh ...!
thanks bạn!!!
This idea is very cool, but also very dangerous, if this plastic can't handle the pressure and it bursts, it goes straight in your face, or it can burst in your hand, be very careful with pressurized pressure, it's very dangerous
hello but you can use the compressor for see how strong is this thing and test it with a lot more pression to see at what point he break this is what people do for air bottles for undersea
На какую площадь хватает одной накачки воздухом? Баллоны с краской обычно наполняют специальным газом , а не воздухом потому что воздух в отличие от тех газов хуже сжимается . А раз хуже сжимается , то давление быстро спадет и нужно будет подкачивать баллон снова и снова.
Rất hay Lắm ❤❤❤❤❤
fun project. good if you have all of those supplies at home. Otherwise easy to go buy new spray paint.
Hay lắm anh Sơn
Paint solvent can easily damage (soften) PVC. It is a color bomb 🎉 if you leave it pressurized somewhere
I wonder about the rubber seals and if they can resist solvents.
So creative, wonderful, can apply and use for many colors, thanks so much.
thanks!!!
Very smart idea. But I suggest using high-pressure resistant PVC... (The blue one in my country).
Có một vấn đề với các gioăng cao su khi tiếp súc với xăng và xăng thơm
Rất sáng tạo.👍
Однажды этот баллончик смачно звезданёт!
Для чего вся эта дрочь нужна была ? паяльник и сосок нужен был ...
Хорошо, если при накачке, всего лишь все краской заляпает, а если к руке при встряхивании..?
Thanks for sharing, it is a cool idea for sure and I will to try it. Just a tip for you, I think that you will find that you will get better results when using your adjustable pliers in the correct direction. You always tighten against the fixed jaw. It makes them easier to hold closed and the teeth in the jaws were made in this way. Most people don't know or think about it, so I thought I would just put it out there since you were nice enough for sharing your idea.
Keo gặp xăng thơm pha sơn lâu ngày nó tróc ra hết còn đâu. Thấy lấy keo pvc dán là ko ổn rồi
Awesome Brilliant idea Bro
Nice share man, thankful
Vậy dùng bình cũ thêm chỗ vào sơn và lắp vòi bơm honda vào thì lẹ hơn không ?
Exelente una crítica constructiva uniera Sido mejor Aser el cuerpo con tubería roscable hasta para llenarla con mayor facilidad y por mejor seguridad saludo y éxitos en tus proyectos
Gioăng cao su làm từ săm xe máy gặp xăng liệu có ổn không bạn?.
🇬🇷 Πάρα πολύ ωραία η ιδέα και η κατασκευή, συγχαρητήρια. Για να δούμε όμως εάν βγάζει αέρα η συσκευή, νομίζω ότι θα ήταν καλύτερα να τη βυθίσουμε ολόκληρη μέσα στο νερό. Τώρα εάν υπάρχει κάποιος άλλος λόγος, εγώ δεν το γνωρίζω.
Já contratei um engenheiro da NASA, para fazer uma dessa pra mim...kkkkkk
Bỏ nước ớt vào làm xịt hơi cay ngon à
Hay lắm nhưng chỉ xài đươc 1 lần thì lổ nặng!!!
good idea, thank you
Thank you!!! Wish the channel grows more and more
Great job, great idea 👏💡
Excelente idea 😊
I tried more or less the same patent, " Paint Bomb !!!!". The thinners dissolve the PVC Glue and then the "spray can" blow apart where the peaces are glued together with a very "loud bang" and paint every where. Use the same method, but just use metal piping (galvanize) that screw together. A bit heavier, but much much more secure.
Thank you for this tuto. What kind of paint did you use ? Paint for car can also be used?
It's going to have to be pretty thin. Should be able to use pretty much any fluid as long as it's not to viscus.
Coleccionaba las bolitas o canicas que venían en los tarro de pintura. Deben estar guardadas ahora vienen piedras 😊
А мне компрессор понравился - мощненький и маленький...
Good stuff used for WD 40 to😊❤
very good idea 👍👍
nice
Thử xì sao không ngâm cả bình vào thau nước nhỉ , làm vậy phiền phức quá .
cool idea but why not use a cheap spray gun? You'll get better results.
Muito legal
Vou copiar
Deus te abençoe em nome de Jesus...
Bình này chiuj đuoc áp lực bao nhiêu psi vậy add?
Bonjour 😊 Vu que je suis français 🤔 il y a des mots que je ne comprends pas 😢😥 mais sinon c'est une super invitation 👍👍 bravo 👏 bravo 👏 vous êtes un génie 😯 🤘🤘🤘
Con algunos usos más es posible que se deterioren las gomas que hacen de sellos y el pegamento que unen los tubos con las tapas por los solventes que utiliza par diluir la pintura
Evidentemente no es el método y materiales definitivos
Tiene más problemas inclusive
Coi chừng nổ bình là cái thứ nhất . cái nữa là zoăng cao su không chịu đc dầu pha sơn
mình dùng sơn gốc nước được ko ạ
1 lần đổ vào bao nhiêu ml sơn vậy anh???
That best for all ❤❤❤❤
Xài một thời gian có phải thay ống nhựa nhỏ bên trong không? Mình nghĩ nó sẽ bị sơn bám vào nhiều sẽ bị nghẹt ông
B. Días amigo. Es buena idea amigo. Sin embargo es muy peligroso, no es un recipiente a presión, por lo tanto no cumple cumple con normas y es un peligro al cargarle el aire. Saludos desde México y que Dios te bendiga.
sử dụng xong cho xăng vào xúc rửa là ok nhé bạn
What is the use of doing this thing? the sprayers to be connected to the compressors are always on the market and have a paint jet adjustment.🤣🤣🤣🤣
You will not find leaks by putting bubbles over something that makes bubbles. Apply soapy water. NOT bubbles.
How do you clean old paint out of your new spray can?
Please learn to hold your pipe pliers correctly.
Bạn ơi mình chế nó cứ bị tắc sơn là sao vậy chỉ dùm mình với
do sơn pha đặc quá đó bạn và trước khi dán ống vệ sinh cho kỹ
@@sonlai ô kê bạn càm ơn bạn nhiêu chúc bạn mỗi ngày có một video mới
KEREN BANG, CERDAS SEKALI
Good 👍
Good way to make a paint bomb 🎉
Mình làm bằng chai coca 1,5L song cũng bỏ sợ bị nổ
Chú cho hỏi là nên bơm bao nhiu kg thì được, chú có thử ngưỡng cao nhất của cái bình nhựa này chịu được bao nhiu kg không?
bình nhựa dán xong để khoảng 2 tiếng bơm 3 - 4kg là vô tư bạn nhé
Congratulations 🎉🎉🎉🎉
Excelente! Ótima idéia ! RJ - Brazil.
Excelente para quê? no mercado existem pulverizadores para serem ligados aos respectivos compressores. De facto, os pulverizadores são seguros, têm um jacto regulável e não tens de fazer este trabalho inútil de cortar canos e colar os canos que depois de duas ou três utilizações se desprendem devido ao facto dos solventes dissolverem a cola.
My thoughts were the same as yours. This is so stupid. 13 dollars for a cheap hvlp paint sprayer and he probably would have spent less money than making this trash.
@@drewrinker2071 in Brazil the same is arround on 200 dollars (no conversion, comparison by minimum wage) so is very cheap to diy
Super video.
As a next level modifications you could get a spray gun and hose from harbor freight so you could change nozzle size. Maybe go with a little larger pipe so you could clean out. careful with pressure. If using latex paint, water will clean out.
Or just buy the fucking paint spray gun intended for this job in the first place for 13 dollars, you know since your already at Harbor Freight. At first I thought that what you comment was going to say
Its reusable! only you need is to clean after use, just as we do in spray guns(cleaning nozzel is a key), its a quality time spent to make as well cheap
I will be sure to “check to see if it fart”. Thank you
Excelente, útil, engenhoso
a mua cái ốc nắp nhựa i ơ đâu đấy
Genial gracias bendiciones
Mình định sơn lại cổng sắt hộp, có bạn nào đã dùng cách này rồi cho mình lời khuyên nha!
Why not thread one of the end caps to allow for cleaning and easier pouring in of paint etc?
Because = RUSSIA
I don't see why it couldn't be done but it would add an extra point to leak from. Plus if it starts to leak once you have paint in there it will basically glue the threaded cap on.
Amazing good job 🤩🙇👍👍👍
Can it be easily cleaned? For example if I want to use different paint color. Because thinner agent might damage the PVC..
There is thinner in the paint once he thinned it down. If you are worried about that use latex paint.
@@user-neo71665 yes. I can see that. I meant thinner agent to clean the tube if one wants to use other paint color.
Способ крепления клапана баллончика к горловине шикарен 👍
Бесполезная самоделка, хватит на 2 пшика, через пару часов краско внутри засохнет, нужно заправлять пропаном, все балончик и заполняются газом))
yg jdi pertanyaan? dlm benak saya. itu lem klau ter,rendam sama bhn campuran cat,seperti bensin/thiner. apa tidak lepas?
I'll just buy a can jeez😂😂
Excelent 🎉❤😂
Răng trong 21 phía trong ống dư nhiều quá khi anh xúc rửa không sạch hết đc
Нормально наверно мыльными пузырями проверять на пузыри! Мастер от бога!
На баллоне четко написано :" Не разбирать и не бросать в огонь" . Какой то другой распылитель и получится прекрасная идея .
Это пишут для рукожопов, им действительно ничего нельзя делать с баллоном
Change the liquid into clear water so we can see the hidden motor pump 😅
Tren ca tuyet voi
Using soft copper or polly seals for pvc not rubber due to the chemicals like brake cleaner. It's best you use mild chemicals in a pvc container. In all and all great pvc spray container.
Bien está felicitaciones
But what if you check to see if it's fart, and it IS fart?! Than what?!
What a genius
Parece un explosivo...!!😂😂😂
amazing niceinfo