Watch as Jamey Jordan shows you the versatility of the Art Roll Kit, #202-100, for use with your Mittler Bros. Bead Roller. www.mittlerbros.com/art-roll-...
hello guys ,thanks for video,, can you show how to fix the starting an stopping bead line where it has a high spot on the metal,,could you use a steel pipe cut it in half then glue a piece of leather on end tap it lightly would this work ,,or do you know another way how remove the high ding,,thanks this will help a lot of people ,i' have ask a lot of people an they said that this was one reason they did not buy a bead roller, a few of them had try bead roller ,,they all had this problem
I want to edge banding to 10mm. the 90 degree angles... My job is the round square, the maximum diameter is the 30 to 45 mm reduced. so how much bedroll wheel diameter required
Thanks a lot for your message today! The dies featured in this video are part of our Art Roll Kit. This comes with the three lower dies, which are nylatron, and one top die that is steel.
There shouldn't be any problem in using these with galvanized sheets. With the bottom rolls in the set being nylatron, mind your pressures as the texture in the those sheets could wear the bottom dies faster. Let us know of any other questions!
Hi there mate just seen this video I like the idea behind them as I have been thinking on doing some bead roller art works for my RUclips Channel Wayne's Garage as well for something to sell but at the moment I don't have a lot of money as I'm studying at the moment and live in my workshop so I was wondering if you guys my like to sponsor my channel for these dies at all thanks for your time Wshne
You should have shown us the back side of each one of those panels without the ink on them we could really see the difference clearly pretty difficult to see with all those sharpie lines from so far away
Q maravilla Exitos desde Duitama Colombia
hello guys ,thanks for video,, can you show how to fix the starting an
stopping bead line where it has a high spot on the metal,,could you use a
steel pipe cut it in half then glue a piece of leather on end tap it
lightly would this work ,,or do you know another way how remove the
high ding,,thanks this will help a lot of people ,i' have ask a lot of people an they said that this was one reason they did not buy a bead roller, a few of them had try bead roller ,,they all had this problem
Excelentes trabajos sigo cada video que puedoa ver.. habría pisibilidad de los subtítulos sean en español??
could you explain how you keep the panel so flat? I have a continues problem with my work curving up on the edges.
Jamey makes many passes at incremental depths to slowly move the material. That really helps keep the panel flat and reduce warping.
Do you pre starch the metal.
What gage aluminum is for door panels and dash
I want to edge banding to 10mm. the 90 degree angles... My job is the round square, the maximum diameter is the 30 to 45 mm reduced. so how much bedroll wheel diameter required
The top roller die is metal or plastic? I have a metal tipping die (very sharp) and leave marks on the metal...
Thanks a lot for your message today! The dies featured in this video are part of our Art Roll Kit. This comes with the three lower dies, which are nylatron, and one top die that is steel.
Apreciado amigo deseo saber cómo adquirir estos troqueles o definitivamente hay que mandarlos a fabricar.
How is this machine? Is it good quality? This is my first time buying a bead roller and I'd like to know is this a good machine? Would you suggest it?
Our machines are all made in the usa and we stand behind everything!
Mittler Bros. Machine & Tool
what ever you do DO NOT BUY baileigh industrial cause its junk with 0 support
How to purchase im from Philippines?
Will these dies work on mild steel 16 gauge?
You'd want to make sure your bead roller has that matching capacity, but if that's squared away you should be just fine on 16Ga.
Can it use for galvanize sheets?
There shouldn't be any problem in using these with galvanized sheets. With the bottom rolls in the set being nylatron, mind your pressures as the texture in the those sheets could wear the bottom dies faster. Let us know of any other questions!
Q precio tiene esa maquina
Adónde la puedo encontrar
I'm from Algeria I hope to work with you
WHAT GAUGE SHEETMETAL IS BEING USED HERE? THANKS
Typically Jamey is rolling with .063 aluminum in these demos.
@@Mittlerbros THANK YOU
ممكن اسم ماكنه
Hi there mate just seen this video I like the idea behind them as I have been thinking on doing some bead roller art works for my RUclips Channel Wayne's Garage as well for something to sell but at the moment I don't have a lot of money as I'm studying at the moment and live in my workshop so I was wondering if you guys my like to sponsor my channel for these dies at all thanks for your time
Wshne
Me gustaría que fuera posible en español muchas gracias bendiciones
¡¡De nada!! ¡Muchas gracias por tu comentario!
লে
You should have shown us the back side of each one of those panels without the ink on them we could really see the difference clearly pretty difficult to see with all those sharpie lines from so far away