Hello friends 👋 Please support me with LIKE, SHARE and SUBSCRIBE 😊 Thanks for watching If you liked it, please support me with LIKE, SHARE and SUBSCRIBE #diy #howtomake #homemade
The maximum particle size must be 1/5 of the nozzle outlet hole. For example with a 3mm nozzle the granulometry or sand, at most 0.6mm. (3mm / 5 = 0.6)
Balkan handyman? More like Balkan Xzibit, "Yo I heard you like sandblasters, so i put a sandblaster on top of your air nozzle and turned it into a sandblaster"😂
I don't have all those things just laying around ready to be destroyed, so I guess buying the real deal would be cheaper for me. Thanks for the video anyway.
Hola tengo una duda LA ARENA es la comun de la pared...te doy like porque esta bueno el video (no conosco la arenadora y estoy pensando en mis rejas que estan destrozadas de pintura gracias.-
Isn't the starting gun already a sandblasting gun? it seems to me that the red container is used to put the abrasive which is then vacuumed by depression
That's a parafin gun but in all honesty if you was to take the nosel off the end I would have thought it could do the same job ... Never tested this theory so would be interesting
@W W this is wrong, I have a sandblasting gun which does not work by gravity but by depression, the tank is under the barrel :) (like the Metabo SSP 1000 for example)
Need a larger compressor. Most people use the 1/4 inch coupler. I see you used the larger one. You can all soak the rusty part in 1 part molasses to 9 parts water for 7 days, and the rust will wash off with running water.
Из пескоструя соорудил пескоструй, этож надо такой хрени в голову придти. Я им радиатор охлаждения масла АКПП промывал раз в год на RX 350, классная штука.
Link of time for 4 years in maritime college. Western thinking with soviet childhood monetize everything, if you wanna live in western world well, keep silence, boast and selfish is the answer.
Con el costo de las dos pistolas que desarmó para hacer una, se podia comprar dos pistolas arenadoras With the cost of the two guns that I disassemble to make one, you could buy two sandblasting guns haha
I tried it ... it works !!! thanks for the awesome video.
I can't get the small pipe out. Please advise
MARAVILLOSO EL INVENTO
Warum hast du es modifiziert????.... funktioniert die Pistole nicht in original Ausführung????
Making a sandblaster out of a sandblaster.
Didn't know that was something i could do at home. Thank you kind sir.
Thought it was a paint gun?
The legend say that 3000 years later he still removing rust from that piece
😜😜😜
legend says you still haven't figured it out how to make it 🤣
Yo iba a fijar el tiempo en 30 días más tarde ..... y fueron 3000 años !!!! Jajaja.
The most interesting part of this was the way to find the centre of a round object
🤣🤣🤣
except he didn't find the center. It was clearly off center.
@@jtltet bjj
The maximum particle size must be 1/5 of the nozzle outlet hole.
For example with a 3mm nozzle the granulometry or sand, at most 0.6mm. (3mm / 5 = 0.6)
Balkan handyman? More like Balkan Xzibit, "Yo I heard you like sandblasters, so i put a sandblaster on top of your air nozzle and turned it into a sandblaster"😂
Ako uzmes staru svjecicu i konektujes na crijevo s vodom dobit ces bolji efekat bez kompresora.
Not bad. With a little extra expense on some BSP nuts n fittings to replace the JB weld I'd say you could up the PSI to make it work even better.
😊😊😊
@@MakeStuffwithLittleDevil I want to buy, cost?
Nice DIY svaka cast za video!!
Hvala brate, svaka podrška znači 😊
this is the video of all time for homefixers!
0:40 you GLUED it ? was it too difficult to buy a simple screwable joint ?
really cool idea
😊😊😊
Этого аппарата хватит на 5 минут, потом все нахрен сотрется песком.
Great idea! Thanks for sharing my friend!
Thanks bro 😊
@@MakeStuffwithLittleDevil You are welcoe my friend
@@christofix 💪💪💪
Very very brilliant idea
I don't have all those things just laying around ready to be destroyed, so I guess buying the real deal would be cheaper for me. Thanks for the video anyway.
Hola tengo una duda LA ARENA es la comun de la pared...te doy like porque esta bueno el video (no conosco la arenadora y estoy pensando en mis rejas que estan destrozadas de pintura gracias.-
Nice DIY idea
Thanks 😊
awesome video
Thanks
Cool
Your calipers have seem better days. Nice trick, I have some spare parts I will try it...at last it is inexpensive. Congrats.
Комментарий не несет смысловой нагрузки, просто поддерживает видео и автора канала.
I am no expert but with pressure and glue . Better wear eye protection, just to be safe. Lot off effort to make vedios, thnaks
Это гениально,взять пескоструй и сделать из него пескоструй.
Хороший пескоструй,шарику яйца щекотать.😆😆😆😆😆
List of stuff that is used in the video would be great! Nice vid
Rickard Weed will cost you a fortune
great job man
thanks bro 😊
Nice idea keep up the good work , will try soon .
😁😁😁
How did it went
Perfect idea..good job bro
Thanks 😊
Isn't the starting gun already a sandblasting gun? it seems to me that the red container is used to put the abrasive which is then vacuumed by depression
That's a parafin gun but in all honesty if you was to take the nosel off the end I would have thought it could do the same job ... Never tested this theory so would be interesting
I thought the same thing .. did he just take apart a sandblast gun to make a more complicated sandblast gun?
@W W this is wrong, I have a sandblasting gun which does not work by gravity but by depression, the tank is under the barrel :)
(like the Metabo SSP 1000 for example)
@@anthonys4685 I presume with sand you need to blow air in from the bottom, unlike with liquids.
Holy cow just buy a sand blasting gun instead of ruining good tools.
Без керамического сопла на 10 минут работы хватит!
А сопло че не показал после эксперимента? Вангую что его хватит на 3-4 банки песка.
can you translate your comment on English?
@@MakeStuffwithLittleDevil 4minut anb dead point
🤔🤔🤔
Looks more expensive than the real thing
😊
what sort of sand is being used? if silica sand it should only be used in a cabinet or full face oxygen fed mask
Rumour has it he is still cleaning that rust off!
Через 5 мин будет сопло на всю ширину трубки...от свечи вставьте керамику хотя бы..😉
Wath is the reason for this complicated construction???
Don't look like it works that good😂
Готовый пескоструй стоит 3,5 копейки, а два пистолета угробил
?
@@MakeStuffwithLittleDevil Чего, по-русски не понимаешь?)))
Cut the bottom off of a pop bottle and tape it to the end of the tip to keep sand away from your face and everything else
Disculpe puedo ponerle agua al deposito
Yes 😁
Need a larger compressor. Most people use the 1/4 inch coupler. I see you used the larger one. You can all soak the rusty part in 1 part molasses to 9 parts water for 7 days, and the rust will wash off with running water.
I'll try and will report back the result. Sorry, skeptical, but love sweet ideas!🤣
Извините но неудачно и очень сложно.
Хуйня полная, если по-русски и своими словами. 🤔
Что за клей используете??
Salute
Из пескоструя соорудил пескоструй, этож надо такой хрени в голову придти. Я им радиатор охлаждения масла АКПП промывал раз в год на RX 350, классная штука.
Looks awesome
Очень намудрил с конструкцией,можно проще,и дешевле
Так этож забугорное видео, забогорные жители, вот и делают все через одно место. Крайне не удобная конструкция, все на эпоксидке. На пару раз...
Lokks nice but how you hold in your hands, looks wery uncomfortable
Сразу видно что не русский
Влага с компрессора идёт а это не для пескоструя!!!
Не говори. Тройник впендюрить не проще было . Чем уродовать пистолет для накачки шин . Не русский блин
😄😄😄😄😄 10 Years later!!!!
Best
Great job ! 👍🏻
What is the red canister please ?
Intelligent!
Проще готовый ( напорный принцип действия
) купить. И эффект будет
, более продуктивнее . А представленное здесь ( деньги на ветер ).
Why not just use the sandblaster you already had?
Where can i buy it? Anyone has information?
good
i Have A Few quession Please Reply Me Soon ?
ok
@@MakeStuffwithLittleDevil What kind of material is used for it?
Только инструметы испортил.
Maybe you need a stronger compressor? What Psi were you on?
I tried a couple diy sandblasters and ended up with a glorified confetti gun.
Как раз на время самоизоляции, убить это самое время и деньги. В качестве развлечения .
Why epoxy? Why not find the right fitting?
Too complicate idea, but works. There is a lot simple way.
give me link for something simple
Link of time for 4 years in maritime college. Western thinking with soviet childhood monetize everything, if you wanna live in western world well, keep silence, boast and selfish is the answer.
RUclipsr: how to make sand blaster!
Comments section: *utter gibberish about soviets and capitalist*
Con el costo de las dos pistolas que desarmó para hacer una, se podia comprar dos pistolas arenadoras
With the cost of the two guns that I disassemble to make one, you could buy two sandblasting guns haha
Exactamente eso pensé
Además necesita un pico cerámico en la salida porque al de metal en un rato lo desgasta por completo.
It sale or not
Это не пескоструй , это игрушка, которой хватит как раз. для видео
I need your copressor for sand blasting, where is ur direct address
Suitable for weak compressors👍
😊
Железной щеткой можно очистить гораздо быстрее
Say no to the jb weld and just get a piece of 1\4 inch fully threaded pipe instead of flipping the quick connect over its much safer
😊
Пистолет для пескоструйной обработки купить не пробовали гораздо проще чем городить не понятно что....
Respect!!!
🤔 interesting I say
takim piaskowaniem to mozesz pankocie swojej piaskowac .......
Three weeks later...
I wonder how the man threaded the hole just with thrusting the drill
I m struggling to remove centre pipe
Cheap sanblaster would probably cost same as these two hardware pieces minus human work...
this parts I got for free 😉
Пипец 700 р стоит мастичная пушка- ей можно пескоструить ,тянет хорошо и эффективнее работает
mis saludos desde venezuela....interesate muy bueno el proyecto
Thanks 😊
my friend. very nice. bravo.. thank you so much....
Thanks 😊
Конструкция чумовая но чистит как-то плохо
?
согласен.
От бусурманин шланг надо бы сверху вставить и трубку не снимать шо в бачке стоит
🤔
Yo quiero saber los de talles de la espuma como se ase i de que liquidos
?
glue on airline fittings i don't think so
чето я непонел в чем прикол?
Испортил инструмент, ради чего?
Nothing was destroyed 😉
павел никоноров он его не испортил а уебал
👏👏👏
Хайпануть хотел , не фартануло
Can i buy a vowel
yhea i would'nt say it's made fron lottel but nice creation of course you first need to buy all that stuff...
I got this parts for free 😉
on a vu plus simple pour sabler !
?
VALLAHİ SÜPER SELAM
🤔
Muy buena la idea ...pero...lastima q no explicas nada
A nozzle will go quickly
Пескоструй!👍☝обалденно задумано!
😉
I’ve never seen such a convoluted mess in my life. Go buy just one sand blasting gun from HF and give up trying to reinvent it for gods sake.
$21 at Harbor Frieght
Why does it have a lot of unlikes ?
I don't understand why people unlike this video?
Jealousy