Realmente um dos melhores projetos. JÁ criado fiz o meu á um tempo me ajudou MUITO nas noitrs sem energia por causa das fortes chuvas que causaram apagão. Obrigado ❤❤❤❤❤
@@Jerryjay3050 bro actual output is ac voltage high frequancy. but after using rectifire the output voltage is dc we run only sum aplinces like bulb,led bulb,tublight,mobile charging,etc & all aplinces wich use inbuilt rectifire for ac to dc the voltage
Hola, no se hasta donde anduvo, yo lo hice con mosfet 3205 con 13007 como vos pero no me anda, tira 380 volt continuos y en alterna no marca nada, quise hacer andar un electeificador que es de un consumo de 0,300 miliamper y no lo tiró jajaja, mire todo pero nada, se cae la tensión, ojalá me anduviera como decis que te anda jajajaa
I always wonder at 12 volts it will pull 8 amps from the power supply to give about 100 watts. The thin wire are not melting where as my project needed a rewinding of the atx transformer to give such performance with much thick wire with out the capacitor voltage doubling circuit. Did input wire became warm after few seconds?
Ohh one thing i forgot mention, i was using tl494 ic. May be thats why i needed thick wires at the input because the ic was adjusting the output voltage with feed back.
Welcome. Cool topic! I did the same, except that I didn't have 220 Ω resistors and I gave 230 Ω. I don't know if the power is the same as yours, I took them out of the 235W ATX. And when I connect a 25W / 230V bulb at the output, the voltage is 170V 😐only. A little bit because you have 4 times as much light bulb (100W) and measurement 224V👍 instead of IRF540 I had IRFP240, resistors instead of 220Ω I had 230Ω, a reactor about 50 turns and the rest is rather the same. Does it affect? I supplied this with a 15V / 4.5A power supply on trial and it only dropped to 13V. Have you run without a load (light bulb, laptop adapter)? I think this may be the fault of the transistors because the IRFP240 have RDSon - 180 mΩ, and the IRF540 have RDSon - 44 mΩ and thanks to that they run faster which translates into further parameters. IRFP240: 20A, 200V, RDSon 180mΩ, IRF540: 33A, 100V, RDSon 44mΩ. Perhaps the 10Ω difference on these 220Ω - 230Ω also does its job. I connected the laptop and it works. Regards.
1:15 On your circuit at the output of the transformer, it is a voltage doubling rectifier. That is, the voltage will be multiplied by 2 times. Moreover, through the rectifier, the voltage will be multiplied by 1.4. That is, in the end: 220v * 2 * 1.4 = 616v ?
When it is unloaded, I have about 380V output, and when I connect a 25W / 230V tospada bulb to about 165V. When I connect a laptop turned off so that the battery recharges itself, it drops to about 150V, and the current flowing at the input is about 4.5A and the supply voltage is about 13V - 14V. I will test it with a 4.5 A and 15 V laptop power adapter - media tech. You have a 100W light bulb and it shines nicely and the voltage is 220V. For me, the laptop xachilacz 90W and 19V output.
@@ElabIndustrial sir please help me. I need to make an inverter which can be used on a load like fridge, TV, bulbs, fan. I want it to be charged on solar. Am really stuck.
Seriously, thank you for this great work, but I am my friend. If I wanted it to output 500 watts, if I provided transistors, would it output more with the same resistors, and it would have a value that would increase?
Cleciano, no es necesario que le pongas los diodos y los filtros, esos componentes son para que el voltaje alterno se convierta en voltaje directo( + y -) pero, lo que interesa es poner los componentes que van en el primario👍👍
Realmente um dos melhores projetos. JÁ criado fiz o meu á um tempo me ajudou MUITO nas noitrs sem energia por causa das fortes chuvas que causaram apagão. Obrigado ❤❤❤❤❤
perfect ji...superp project.....i try ur project..100 % working..without any fault...
Thank you!
@@ElabIndustrial is it ac or dc as the output...?
@@Jerryjay3050 output dc voltage, Thanks
@@Jerryjay3050 bro actual output is ac voltage high frequancy. but after using rectifire the output voltage is dc we run only sum aplinces like bulb,led bulb,tublight,mobile charging,etc & all aplinces wich use inbuilt rectifire for ac to dc the voltage
@@vijaykumar-fb6yp also how do we convert to achieve so as to power a motor e.g fan
Um dos melhores videos que já assisti. Parabens!
When i watched your video i feel like a thirsty person found sea 👍❤️
Muy bueno amigo ...garan idea ...13007 transistor me funcionó ... gracias éxitos ...desde Cuba un saludo
Please language English, Thanks
@@ElabIndustrial very good I do it whiths transistor 13007 thank you very much
Hola, no se hasta donde anduvo, yo lo hice con mosfet 3205 con 13007 como vos pero no me anda, tira 380 volt continuos y en alterna no marca nada, quise hacer andar un electeificador que es de un consumo de 0,300 miliamper y no lo tiró jajaja, mire todo pero nada, se cae la tensión, ojalá me anduviera como decis que te anda jajajaa
Nive Video Big Bro 👌👌👌
Hello very good video thank you
Welcome
I always wonder at 12 volts it will pull 8 amps from the power supply to give about 100 watts. The thin wire are not melting where as my project needed a rewinding of the atx transformer to give such performance with much thick wire with out the capacitor voltage doubling circuit. Did input wire became warm after few seconds?
Ohh one thing i forgot mention, i was using tl494 ic. May be thats why i needed thick wires at the input because the ic was adjusting the output voltage with feed back.
Seu projeto ficou top, parabéns amigo e bons projetos.
Please language English,Thanks
@@ElabIndustrial He said: "Nice project. Congratulations bro, show more good projects."
@@ElabIndustrial привет.а ето жолго служит?
Welcome. Cool topic! I did the same, except that I didn't have 220 Ω resistors and I gave 230 Ω. I don't know if the power is the same as yours, I took them out of the 235W ATX. And when I connect a 25W / 230V bulb at the output, the voltage is 170V 😐only. A little bit because you have 4 times as much light bulb (100W) and measurement 224V👍 instead of IRF540 I had IRFP240, resistors instead of 220Ω I had 230Ω, a reactor about 50 turns and the rest is rather the same. Does it affect? I supplied this with a 15V / 4.5A power supply on trial and it only dropped to 13V. Have you run without a load (light bulb, laptop adapter)? I think this may be the fault of the transistors because the IRFP240 have RDSon - 180 mΩ, and the IRF540 have RDSon - 44 mΩ and thanks to that they run faster which translates into further parameters. IRFP240: 20A, 200V, RDSon 180mΩ, IRF540: 33A, 100V, RDSon 44mΩ. Perhaps the 10Ω difference on these 220Ω - 230Ω also does its job. I connected the laptop and it works. Regards.
1:15 On your circuit at the output of the transformer, it is a voltage doubling rectifier. That is, the voltage will be multiplied by 2 times. Moreover, through the rectifier, the voltage will be multiplied by 1.4. That is, in the end: 220v * 2 * 1.4 = 616v ?
Mosfet IRF630 serve?
Can v use diode in4007 instead ofFR302??? Please kindly reply.??
UF107 RF107 FR302 is possible
Excellent! What sine wave we have at the output?
Square wave
I can put two mosfet 3205 and are they going to break ???
U can try, possible, Thanks.
Sir, i did it as you teach and it s working well, unless some sounds from the 2 capacsitor, i m so wonder!
Very nice sir ❤️
When it is unloaded, I have about 380V output, and when I connect a 25W / 230V tospada bulb to about 165V. When I connect a laptop turned off so that the battery recharges itself, it drops to about 150V, and the current flowing at the input is about 4.5A and the supply voltage is about 13V - 14V. I will test it with a 4.5 A and 15 V laptop power adapter - media tech. You have a 100W light bulb and it shines nicely and the voltage is 220V. For me, the laptop xachilacz 90W and 19V output.
Can i use 13007 transistors?Please reply 🙏
Can I use E13007-2 if possible, how much bra is used?
bro 13007 is a transistor c& irf is a mosfet
Yes you can
Olá elab industrial qual é a frequência deste tipo de conversor?
Can any other transformer do better apart from ATX transformer like E and I transformer
Can use another dioda ?
you must be use Ultra fast diode, thank you 💖
Hello sir
I just wanna know if this can be used for a regular purpose I.e mor than 5 hours continuous.
Bad performance, mosfet very high temperature, Thank you,
Comming soon perfect 12v to 230v step up inverter
@@ElabIndustrial thanks
You can always tropicalize it with a fan.👍
@@ElabIndustrial sir please help me. I need to make an inverter which can be used on a load like fridge, TV, bulbs, fan. I want it to be charged on solar. Am really stuck.
what is maximum output power to this circuit? is it 230vac or 230vdc?
Maximum power output
By rewinding primary to secondary and secondary to primary, can 12 0 12 be made out of 220 ???
Creative video, thanks :)
Amazing ,hi can i use transistor 13007?
Will table fan works in it
Amigo posso usar os mosfete irfz44n
Can we use 12012 transformr
GOOD VIDEO, BUT SIR HOW MUCH WATT RESISTANCE
Vai output a jakono diode use kora jabe ki ar resistor gulo koto watt
Kya ham irf z 44n ka use kar sakte hai plzz reply
I used it here irfz44n you can use irf540 if you want,Thanks
@@Harishbhardwaj000 please language English Thanks
Is this inverter 12v DC to 230High DC
Thx from POLAND :D
What's the maximum ammount of watts this transformer can provide?
Good project,,
If the electricity run on MOSFET MOSFET will be hot?
can i use irf3205?
Possible you can try
What are the parameters of the pulse transformer?
Can I use uf4007 diode in place of FR302 diode ??
Use Ultra fast diode
no bro 4007 is a silicon diode plese use a schotky diode
Yes
hello,this can use 6v baterry?
To use this circuit you must go to the 12 volt supply,Thanks.
Bro how many watt can use for this project?
Very nice sir
Thanks
@@ElabIndustrial sir hamare liye koi asan sa inverter tayar karen 500 watt ka please sir
@@Khankhan-oi2wu i will try Thanks,
@@ElabIndustrial thank you sir
التيار المطلوب للمبه هذه Ac بينما التيار الخارجDc مع الدايودات والمكثف المستقطب كيف؟؟؟؟
What should I modify so that at the output it delivers 120 volts?
Mega-Soft secondary wire number of turns
Good job....
Thanks
👍👍👍👍👍👍
شكراً لك جزيل الشكر على نفرتر
Fiz mas ai virou dc e não ac? Com dc não da para por fios mais longos.
the output is dc?
Yes output dc voltage
how much watt and hz can use for smart tv ?
Sir z44 use kar sakte he.????
Fantastic. Bro, does it work properly?
It works properly up to a maximum of 100 watts,Thanks
Seriously, thank you for this great work, but I am my friend. If I wanted it to output 500 watts, if I provided transistors, would it output more with the same resistors, and it would have a value that would increase?
Can i use 13007 transistor
CAn i ran a 80W ac fan ?
@@BastelPichi no it’s not possible(tested)
Can we charge the mobile
hohow mamany wawatt resistance use u?
Can I use it for 3055transistor amplifier circuit?
Can you use in4007 diode?
Use by500 or by550 or 1N5408
@@ElabIndustrial yes
Can you use 1n5844 or FR157
@@clonapp6654 you try 1N5408
@@ElabIndustrial Can you use FR302
Hi, I rode an inverter of this , however I have a question , how many wats does it support ?
Схема рабочая, но 100 ватт тут нет, на 15 ватт лампочка горит, и почему то перегорают резисторы на 220 ом, не пойму в чём причина
Kya ham ak hi capacitor 450v or 33uf ka le sakte hai
@Utkarsh Rana kya aap ak acha auto cutt off chargr bana sakte ho
@Utkarsh Rana ok bhai
inductor 47uh..??
🇮🇩🎀👍👍👍🎀🇮🇩🙏
Thank you so much.
why was"nt the bulb placed farther away from the circuit .
The current inside and outside please?
How much 220v dc volts can a 220v AC device operate?
Dc to Ac operates ruclips.net/video/T8RmVCc9UF4/видео.html
Amigo,se eu usar dois diodos 1n4007 e dois mosfete irfz44 fuciona
1N4007 not working high frequency switching, you use to by500 or by550, Thank you!
@@ElabIndustrial ok amigo obrigado
Cleciano, no es necesario que le pongas los diodos y los filtros, esos componentes son para que el voltaje alterno se convierta en voltaje directo( + y -) pero, lo que interesa es poner los componentes que van en el primario👍👍
Jaja 🤣 después de un año gracias, thanyou @Elab industrial
Sir
I have many transformer of 12 v single
Not 12+0+12
Only 12v
Give me the idea to make 220v inverter
Hola bom dia o amigo pode me dizer quanta horas é a duração da bateria nesse circuito com uma lâmpada de 9w?
He can work z tv ?
Working but 100w max, Thanks
kew re bbhaii eish trick kew kam nehi kora pura apke jasha kora thaa step to step.but kew nehi huiaa
Brother can use bulb 40W not
Yes You can less & More than 40w but 220v~v
Sorprendente!!
1:14 third wire nhi he output me
Total power output ?
Back up time?
Con cuanto hz trabaja? 50 Hz o 60 Hz
Frecuencias del orden de los khz a partir de 40khz
Registor koto watt use korsen
What is the transformer ratio?
Bhai circuit diagram bhejden
lifetime ???
Bhai yhe ban Sakta hai possible hai comments plz
100% true no fake.
yes bro
Durasi kuat berapa jam kah. Master
how many watt of resistor?
Excelente, gracias Elab
Thank you!
very good
Thank you!
its awesome
Welcome
Kuweelkone pirang vol bos
How for 110 vac ???
mosfet irf z44n use kora jabay ki
হ্যাঁ IRFZ44N ব্যবহার করা যাবে, ধন্যবাদ
Muito legal...👍👍
how many power consuption
Can i use 330 ohm rasistor i have not 220 ohm
Thanks bro
Using IC 13007 is not he taken from ATX source
Amigo e de quantos w
Nice